The Innokin iTaste VV V3 owners group

[brookj1986]

Just completed my order from slowtech. Ordered an Atomizer resistance tester, Nemesis Style mod, kayfun 3.1 ES Kit, switch magnets(10 pack as they were out of stock on the 2 pack) for Nemesis mod, and the Variable wattage kick (only ordered this as a temporary until I can afford the Evolv Kick 2 as I just spent my next month's budget for e-stuff on this order). Most of the stuff isn't going to be ready to ship until 3/25, so I won't see if until around this time next month, but I'm happy about it.

Unfortunately, the cheap kick from FT doesn't allow sub 1.5 ohm coils, so it'll only be used on certain occasions. Figured for $8.33 I couldn't go wrong instead of the $45 for the kick 2.

 

[brookj1986]

The Aro head is the same as the PT/Evod, and will NOT go in the T3S. But the T3S will work in the others. The part at the base that looks like a thin flat washer is bigger diameter on the Aro and PT than it is on the T3S, which will keep it from fully seating in the T3S. But you really have to look close - and at one of each at the same time - to tell.



Have a SvoeMesto Kayfun clone that's really nice
And the KHPro KHMod, with it's bottom side button has some nice features for the "low" end of the mech spectrum.

Happy to spend your money

I just got the aros. The stock aro atty has a much smaller flat disk than the evod/protank/unitank coil. Evod coil still fits, but with over hang. I'm sure it's still usable. Still need to rebuild them.

Sent from my Galaxy Note 3 using Tapatalk. Excuse typos and stupid autocorrect errors.

 

[alisa1970]

I just got the aros. The stock aro atty has a much smaller flat disk than the evod/protank/unitank coil. Evod coil still fits, but with over hang. I'm sure it's still usable. Still need to rebuild them.

Sent from my Galaxy Note 3 using Tapatalk. Excuse typos and stupid autocorrect errors.

I have the "old" style evod heads with the short chimney. I tried them in my Aro II and they don't work--well they do, until they start leaking. I do have some Fasttech Tumbler clones that came with a longer chimney and those DO work fine in my PT2 and Aro II.

 

[brookj1986]

I have the "old" style evod heads with the short chimney. I tried them in my Aro II and they don't work--well they do, until they start leaking. I do have some Fasttech Tumbler clones that came with a longer chimney and those DO work fine in my PT2 and Aro II.

Yeah... Short chimney on mine too.

Sent from my Galaxy Note 3 using Tapatalk. Excuse typos and stupid autocorrect errors.

 

[DavidOck]

If the new ARO has gone to the smaller diameter head, you might not get a good seal with the PT heads, since it may not screw down enough to prevent leaks. In my experience, chimney height has little to do with leaking. If it doesn't leak when laid down flat, that part's probably ok. Of course, ymmv. But the base diameter can prevent a good seal. And leak to the battery.

Mine are both approaching a year old, and we all know how the makers like to change things up....

 

[chapeltown]

Can I say....I really love the look, feel and features of my VV v3's. What disappoints me is that they don't last me all day, being 800mah. I wish version 4 would be 1100 or 1300mah. That would be awesome!!

Sent from my SCH-I545 using Tapatalk

 

[PaulBHC]

My VV came today! My MVP quit working a couple of weeks ago and I really missed VV/VW. I wanted something smaller for work and bought a ego twist. Good item but no passthrough and even at 1300mah would run out when I didn't expect it.

 

[Downtownjeffbrown]

First off this is completely my fault. It fell out of my pocket at work and I ran it over with a bobcat on accident. Just wanted to show you guys how much this device can hold up too and still fire. Everything still worked including the screen. I didn't wanna vape on this as I have no clue what could go wrong while using it. So I sent it to a friend that is building her own mod and can use the parts in this. Cheers :beer:

>^·^< Sent From MEOW G2

 

[brookj1986]

If the new ARO has gone to the smaller diameter head, you might not get a good seal with the PT heads, since it may not screw down enough to prevent leaks. In my experience, chimney height has little to do with leaking. If it doesn't leak when laid down flat, that part's probably ok. Of course, ymmv. But the base diameter can prevent a good seal. And leak to the battery.

Mine are both approaching a year old, and we all know how the makers like to change things up....

Technically, I have the v1 Aro. I'm sure it could be changed and still be called a v1.

That being said, the first Aro that I rebuilt, the rubber washer that you put to separate the wires tore... The PT washer fits perfectly and is silicone not rubber so it is easier to work with. PT coil = replacement parts for the Aro. Chimneys are actually same height but the whole aro coil unit is slightly taller than the evod/PT coil setup.

Sent from my Galaxy Note 3 using Tapatalk. Excuse typos and stupid autocorrect errors.

 

[PaulBHC]

If you order another one online, you should send the vendor these pics to show how it arrived. Just for a laugh, not dishonesty.

 

[Downtownjeffbrown]

If you order another one online, you should send the vendor these pics to show how it arrived. Just for a laugh, not dishonesty.

Haha...

Well. Did order another but it was black not white this time lol. I'll remember that though for next time

>^·^< Sent From MEOW G2

 

[brookj1986]

Man, I've spent more in the past month than I've spent in the previous three on e stuff... I was in the positive with money saved since quitting during January and half of Feb... Not so much anymore.

Just received a few new juices from NicoTicket. Never tried from them before. Betlegeuse is outstanding, The Virus H1N1 -- wish this was the first tobacco based flavor I tried when I first quit analogs. Straight from the mailbox I taste a bit of caramel, some vanilla and a great deal more complex than my pallette can decipher, but it's great.

Haven't yet tried Custards last Stand, going to let it steep, but reviews were great.

Sent from my Galaxy Note 3 using Tapatalk. Excuse typos and stupid autocorrect errors.

 

[PaulBHC]

Simple fix for spending more than your banner shows saved is to do a new banner with a higher price for the cigs.

 

[chapeltown]

Simple fix for spending more than your banner shows saved is to do a new banner with a higher price for the cigs.

You are on fire tonight, Paul!! lol

Sent from my SCH-I545 using Tapatalk

 

[chapeltown]

Man, I've spent more in the past month than I've spent in the previous three on e stuff... I was in the positive with money saved since quitting during January and half of Feb... Not so much anymore.

Just received a few new juices from NicoTicket. Never tried from them before. Betlegeuse is outstanding, The Virus H1N1 -- wish this was the first tobacco based flavor I tried when I first quit analogs. Straight from the mailbox I taste a bit of caramel, some vanilla and a great deal more complex than my pallette can decipher, but it's great.

Haven't yet tried Custards last Stand, going to let it steep, but reviews were great.

Sent from my Galaxy Note 3 using Tapatalk. Excuse typos and stupid autocorrect errors.

Brook~ I have been looking at that vendor for a long time but haven't ordered yet.... it is funny, all the reviews for H1N1 look good, but every time I see it, it makes me think of my father in law... He calls it "the Heiney virus!

Sent from my SCH-I545 using Tapatalk

 

[brookj1986]

Simple fix for spending more than your banner shows saved is to do a new banner with a higher price for the cigs.

You make a valid point. Especially with the Dollar plus increase since January 1st.

But still, doesn't change my ridiculous spending in the past month.

Sent from my Galaxy Note 3 using Tapatalk. Excuse typos and stupid autocorrect errors.

 

[Storm52]

Brooke, you aren't alone with the spending. Somehow I now have 2 provari, 2 mech mods coming, a russian on a coop, two carto tanks and I don't even own any batteries or a charger.

 

[Storm52]

BTW, you are going to love NT CLS and pretty much anything in your flavor liking.

 

[bathomassr]

My first vv v3 bit the big one last week, so ordered 2 more (that'll make four). The battery just wouldn't hold a charge anymore. As far as tanks go, I'm back to mini PT2. I just haven't been able to find a tank that works as well and is as reliable as the mini pt2. Tried aspire nautilus, pt2, iclear, etc. Love the mini pt2 on the vv v3! Perfect vaping solution for me.

.....

 

[Capt.shay]

First off this is completely my fault. It fell out of my pocket at work and I ran it over with a bobcat on accident. Just wanted to show you guys how much this device can hold up too and still fire. Everything still worked including the screen. I didn't wanna vape on this as I have no clue what could go wrong while using it. So I sent it to a friend that is building her own mod and can use the parts in this. Cheers :beer:

Good job! I am a PV destroyer as well. This ego came flying out of the shoot from under my LawnBoy mower and still fired.