Congratulations!!just noticed that today is my 666th day without smoking ..."Woe to you o earth and sea.."
The Overlooked Tootle Puffer Gear Thread
- Thread starter roxynoodle
- Start date
- th_trl_thread_readers 0
- Status
I should hit my 6,666th day around June 1st 2034, when I'll be about 77 1/2 years old. And, I should still have nic!just noticed that today is my 666th day without smoking ..."Woe to you o earth and sea.."
I need a will.
"Let him who hath understanding, reckon the number..."just noticed that today is my 666th day without smoking ..."Woe to you o earth and sea.."
Up the Irons!
Came home to a little box sitting on my desk...received the $5 Proms and couldn't be happier! Love this atty! Set up all 5 and been switching them out on my Provaris - Now my atties outnumber my Varis lol
The draw is much tighter than my Prom v3 but thats ok - still excellent flavor. I may take one and try to drill the airhole/post out to 1.8/2mm. I'll need to wait till the middle of the week when I'm off to give it a try. Anyone else give this a go successfully?
The draw is much tighter than my Prom v3 but thats ok - still excellent flavor. I may take one and try to drill the airhole/post out to 1.8/2mm. I'll need to wait till the middle of the week when I'm off to give it a try. Anyone else give this a go successfully?
Ridiculously off topic so sorry in advance but I just bought my tix for Edmonton show woooot! Second time seeing them, first time was incredible!"Let him who hath understanding, reckon the number..."
Up the Irons!
Too Fine!
I have never seen them live, it would be quite excellent!
They are phenomenal my friend. Incredible performers who have honed their craft for a very long time. One of the best if not the best show's I've ever seen (and I've been to A LOT!). If you get a chance to see them this tour do it!
Always
Here is something to try Tamer, if you want to test out Ni200 wire as well.
I just did a build on the Rose V2 using 28g Tempered Nickel for a change from Ti. A 7/6 wrap on 2.5mm comes out to 0.08 ohms and fits quite nicely. Wrap tight but very wide spaced on a 2.5mm screwdriver, then push all the coils up to one end and let go, you will end up with perfect spacing. Trim and mount the coil. I wicked this with part of a dm Viskose ball from the EU, as you unroll them they are perfect width to fit a 2.5mm coil after rolling. The Tempered Ni200 makes it quite easy to pull wick through the coil from one side.
Vaping very nicely at 35J/451F with Song's Blend #7 in 50/50 from Vaporus out of Montreal.
Didn't get any wick pictures as the HTC wouldn't focus on it with that much white, here is the coil though.
I use this height.
Did those of you who got the Prom v2s adjust the air screw? If not, that might help. It uses the allen key in the box. There's an airflow adjustment screw on the bottom of the base. I brought mine out to be flush withtne base so it didn't get stuck on my mod (air channels) or scratch my mods.
While not that particular topper, I generally use a tiny dab of rubber cement on that type screw. Back it out so you can see the threads, use a toothpick dab on them, then adjust to where you want. Makes a good thread lock so they don't back out in use, but easy to undo if desired.
I will say, unlike some Kayfuns, the air screw never backed out on me . But, that's a good idea, David.
. But, that's a good idea, David.
Yep, some of the KFs are a bit loose... and while some folk take the screw out, I prefer it in, but flush. Had one back out from vibration, not enough to jam, but noticeable when I removed it... and didn't want to use a permanent thread lock compound.
- Status
Similar threads
