- Status
... and his longer brother:
Anyone know how to clean this Satin SS? Will the SS Cleaner works on the Satin surface?
MM told me today that there is a delay in shipping because of an issue with the engraving in the back cap...any one else have this issue?
Full brass edition Poldiac just released, and got another Poldiac 
... If anyone has the satin uma edition, I'm interested. Hard to find because it was a limited edition. I'm wondering if this edition will be limited as well.
... If anyone has the satin uma edition, I'm interested. Hard to find because it was a limited edition. I'm wondering if this edition will be limited as well.Full brass edition Poldiac just released, and got another Poldiac
I just ordered one yesterday as well. My first Poldiac. I'll be stalking the UPS site for delivery!!
My Poldiac (all brass) should be coming on Friday (yay!) and now I just need to find an rba to put on it. I am considering these right now:
1. Steam Turbine (only issue is availability - waiting to get on VW where I hope I can snag one)
2. DID and Short DID (only issue is that they won't be back in stock for a few weeks)
3. Z-atty U (already quite familiar with Zen devices, but have concerns about voltage drop)
With regard to #3, do any of you use a Poldiac/ZAU combo? I would be interested to hear what kind of results you are getting. I have no interest in sub-ohm coils (usually go for 1.5-ish ohms) but I want to make sure that these two devices play well together before placing an order. Thanks in advance!
1. Steam Turbine (only issue is availability - waiting to get on VW where I hope I can snag one)
2. DID and Short DID (only issue is that they won't be back in stock for a few weeks)
3. Z-atty U (already quite familiar with Zen devices, but have concerns about voltage drop)
With regard to #3, do any of you use a Poldiac/ZAU combo? I would be interested to hear what kind of results you are getting. I have no interest in sub-ohm coils (usually go for 1.5-ish ohms) but I want to make sure that these two devices play well together before placing an order. Thanks in advance!
Well I am a little bit bias as I'm not a huge fan of Zen~'s stuff.
But I have to say there is no denying the look of a Poldiac in 350 mode w/ short did or 490 mode with standard did. When you line up the dual MMV logos w/ wick over the botton... man that looks sexy.
Not to mention I vapes incredible w/ a sub-one coil and brass centerpost. 350 and short did = My all day/ carry.
I ended up ordering a ZAU yesterday (if it doesn't work out I can always throw it on my Provari) and I ordered a standard DID this morning. I would have preferred a short DID but I couldn't pass the standard up. Thanks for the feedback!
All you need to run a short is a second tank, centerpost and inner tube. MMV's Pyrex is nicer than IBtanked, flame polished...
short-did-converter
Short did = 2 mil capacity but man, love it on my Poldiac in 350 mode.
I'll probably do that somewhere down the line but I have spent far too much money lately, and I still have a couple expensive things on my list to pick up.
I missed it. Wish i kept up with updates. I hope they do one more run.Full brass edition Poldiac just released, and got another Poldiac
Just cleaned all my brass contacts and wrapped a 3/4 28g coil on ceramic (first time running ceramic). I am seriously blown away! I'm not even at sub-one and I can honestly say this the best vape I've had.
I slammed some Good Life melon boba in the tank, not knowing what to expect. Kinda wish I had filled w/ Pluid or Maha Ras...
Anyways, had to brag a bit. If you are going to run a brass positive/centerpost and nut, these (Pro-Grade Abrasive Fiberglass Pen : Fiberglass Pens | RadioShack.com) are handy for cleaning contacts.
I prob dissembler and clean my did once ~ a week. I'm running around 40 - 50 mils through it between a complete disassemble. It is kinda a pain but if there is any voltage drop at all (from batt to did's ground and centerpost) my meter isn't picking it up.
My only criticism of the did is there are so many tiny parts and you have to completely break it down to clean the contacts, or to give the tank a really good rinse. I mean I did have threading issues w/ the did on a P+ (hence the poldiac) but that is a easy fix w/ a 7 x .5mm adjustable die.
Haha, I know what you mean, these thing are not light on the pocket book. I have an ELA, Nimbus, SS Hornet and some Filipino drip tips coming, and that's just hardware. Maybe it's time to sell something...
hi,
I am thinking of getting this mod. one question regarding to UPS shipping. Does anyone get charge for brokerage fee or any other ridiculous fee by UPS?
I am thinking of getting this mod. one question regarding to UPS shipping. Does anyone get charge for brokerage fee or any other ridiculous fee by UPS?
Is that FC-2000 ceramic or another kind? I have some coming in the mail tomorrow that I am anxious to try but I am not 100% certain how to prep it. I have heard that people are soaking them in PG/VG for a couple days and even microwaving them. Given that you had good results, what did you do?
I want to get my hands on a Nimbus, too, but I can't seem to find it anywhere.
The new Poldiac should be showing up within the next few hours - can't wait!
- Status
Similar threads
