The Roller SS-P telescopic battery mod from atmizoo
- Thread starter outadadark
- Start date
- th_trl_thread_readers 0
- Status
Man I dunno what I am doing wrong. I've followed all the suggestions on the roller website and most followed in this thread. Changed out the spring, cleaned the switch, cleaned it again, took the spring out completely. I have several mods and just for comparison sake I took a battery(second charging cycle) and put it on the roller with a DID on top. 1.8ohm coil. The vape was anemic. I put the same battery and same atty on top of my GG and my gus tele and they just produce a insane amount of vapor and flavor in comparison. Dunno what else to try.
Hey guys, been looking into the Roller and stumbled upon a used Roller SS-P. It has been dropped, and looks like it was dropped on the bottom cap, which produced scuffs. He is willing to let it go for $115. Should I go for it? Or wait till the local B&M gets them back in stock at $160+tax.
Sadly the bottom cap is the only thing Atmizoo does not make. If the rest of the body parts are practically flawless, i'd say go for it. Most of the time you're not even looking at the bottom cap, but personally that would bug me and i'd ask Atmizoo if they'd be willing to make a bottom cap.
With that said, if you can order a bottom cap, i'd order a couple other things and you'd still come up on the deal.
Your call.
With that said, if you can order a bottom cap, i'd order a couple other things and you'd still come up on the deal.
Your call.
Did you put a silver bullet copper spring in? Also make sure you have unscrewed the pin in the 510 connector so you are getting a solid connection with your atty other wise you get weak power.How did the plated silver look in the switch , where there any dark marks? How did you clean it? Give me a bit more info and I will try and help , I had the same issue with mine for a while and nearly sold it but I have it working really well now.
Same here. I haven't changed out the spring, as it's working quite nicely for me as is, but I did have problems firing the atty until the pin was raised just right. That was all on me. The Roller worked flawlessly. (still does!) I hope your (the poster AB is replying to) situation is likewise. Try raising the connection higher than you think it should be, then attach your atty, see how it works. Adjust as needed. Good luck! And if it still doesn't work, make arrangements with Manos to send it in for repair. They have great CS!!!!
Thanks for the replies guys. I actually had a copper spring from another mod laying around that fit perfect. In the tradition of being obsessive about my mods working the way I want them too I havnt given up. I actually took the spring out again this morning and set her up. I screwed the positive post all the way down and messed with the center pin of the atty I got for the device(bliss). Turns out it must have been the connection being a bit weak becuase it seems like a whole different mod. The thing is hitting a lot more like I expected it too. Turns out no matter how many mods you have owned or played with every one is different and they all have their learning curve. I feel like a noob. Lol thanks again guys
Fantastic!! Now you'll have the battle of trying to let go of it for a minute, like the rest of us. Good luck with that, I can't help you there. lol.
I setup a 0.8Ω twisted wire coil on my RBA lastnight and the difference is night and day, I might have to pocket carry the Roller with a IGO-L instead of the Provari lol... Just scared to mar up the polished finish 
Maybe a customized leather cigar tube like pouch would work for your pocket? Twould be a shame to have your keys and whatnot mess it up like you said. I've been carrying a torn off slice of cell foam sheet in my pocket. Works great for now.
I always separate my keys from my mods in my pockets. Not going to mar up a $200 setup over some house/car keys lol.
Cigar tube or a tiny telescope tube sounds like a great idea, but might look weird in the pocket........ LOL
Cigar tube or a tiny telescope tube sounds like a great idea, but might look weird in the pocket........ LOL
I already had the problem trying to decide what to use before this showed up and now I have to have three mods on my desk at work and three more at home waiting to be vaped. I went a little crazy this month but at least now I can have 6-7 juices in rotation but the roller might start going with me out and about just cuz of its design and size. Sigh 1st world problems ;-)
Starting to wish I got a full matte or even ice matte roller for on the go, looks like a very sturdy finish. Maybe i'll ditch the ProVari and pick up another Roller... But I wanted to pick up a Chi-You... Aish, first world problems for sure...
LOL, I hear ya. Last year, I was able to buy one mod, one genny, due to Hubby's health issues. This year even he's splurging for me! I love living in the 1st world, the 3rd world sucks. Get it while the funds can be juggled, that's my new motto.
Received a SS-M Roller yesterday and promptly tried to attach my AGA-T into the recessed brass connector. Not a good idea! Threads on the AGA bound as I tried to cinch it down. Sorry if this has already been covered in previous posts, but what is the secret to getting this dog to set? Noalox? Machine shop? Pi??ed off, so yesterday I ordered an AC9. Hopefully that screws into the connector. Would a SS recessed be a better solution?
Roller is a COOL little mod! In short 18350 mode I can't believe how tiny it is. Hope the AC9 works!
Roller is a COOL little mod! In short 18350 mode I can't believe how tiny it is. Hope the AC9 works!
- Status
Similar threads
- Locked
