Thanks for all the replies. Looks like a rose it is! Just have to clear some other gear out before moving forward. [emoji6]
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
The Rose v2 Rebuildable Atomizer
- Thread starter SINphul
- Start date
- th_trl_thread_readers 0
- Status
I'm waffling here...so many choices! Any thoughts on the ubertoot compared to the rose?
Sent from my iPhone using Tapatalk
The ubertoot seems to have a problem with condensation and juice getting in the base and causing gurgling , according to what I've read both the authentic and the clones are susceptible to this . That's enough to put me off of ordering one . However my third Rose should be in my hands tomorrow . I've gone through a crapload of atty's and nothing else delivers the flavor of a Rose V2 with the bulletproof reliability of a Rose IMO . Best rta out there IMO .
My fourth Rose V. 2 is here 
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
My Snapdragon has Shipped!
Looks like FT has translucent bell tanks in for the Rose V2 Stumpy...
They have mislabeled them as Snapdragon Bell Caps...
$10.02 Replacement PC Bell Cap for Snapdragon RDA Atomizer (4 Pieces) 4-pack - ships one of each color at FastTech - Worldwide Free Shipping
Looks like I'm going to have to get a stumpy.
They have mislabeled them as Snapdragon Bell Caps...
$10.02 Replacement PC Bell Cap for Snapdragon RDA Atomizer (4 Pieces) 4-pack - ships one of each color at FastTech - Worldwide Free Shipping
Looks like I'm going to have to get a stumpy.
Take the tank off and check to see which post your exterior air-hole is in line with (more or less), the positive or the negative. If negative, it's obstructed by the insulator, and you'll need to cut off a piece of it. If positive, then the Rose just may not suit you.
Got a rose v2 through the classifieds, and now I understand what everyone here has been raving about! Well made atty with amazing flavor!
The draw is pretty tight so it's more of a chill out and enjoy the vape kind of device...not as good when you're needing a vape fix because the draw requires some patience. But I'm enjoying it so far!
Sent from my iPhone using Tapatalk
The draw is pretty tight so it's more of a chill out and enjoy the vape kind of device...not as good when you're needing a vape fix because the draw requires some patience. But I'm enjoying it so far!
Sent from my iPhone using Tapatalk
You can always go to a vertical coil if you want more airflow .
I have three Rose atomizers. Some time ago on this thread, I described a problem I had noticed on the second one, namely that the airhole was obstructed by the upper insulator resulting in a less-than-optimal draw. After a small alteration, the problem was resolved. Now I am performing the same alteration on my third Rose. Since I doubt that I'm unlucky enough as to have received the only two Roses like this in existence, I thought I would take some pictures along the way to illustrate exactly what the problem is and how to fix it.
This is the upper insulator:
The screw on the left side transfers current to the positive post. On the other side, there is a semicircular projection that hangs down well past the rim of the upper base. The upper base is screwed onto the lower base to form a single unit. The lower base has the exterior airhole. When the two are screwed together, the airhole may end up on the positive side of the upper base or the negative side (this varies between atomizers, not on a single atomizer). If it winds up on the positive side, all is well. This one, however, winds up on the negative side:
As a result, the airhole is obstructed by the insulator. If I turn on the flash, you can clearly see it:
I asked the guys at Eden Mods about this, and they said their CNC machines were not programmed to avoid this, since there’s space between the airhole and insulator and therefore air can still get around it. That’s true, but having experienced it both ways, I can tell you that the difference is significant. The draw on this Rose, pre-alteration and fully open, is about the same as it will be nearly closed post-alteration.
To fix the problem, insert a sharp pin against the right rim of the airhole and dig it into the insulator. This will mark where you need to cut:
Now use Mr. Razorblade to cut down through the projection. Do it at such an angle as to make sure both the exterior and interior airholes are unobstructed (the interior airhole is in the center of the insulator disc). Just beneath the blade you can see the beginning of an incorrect cut:
Now flip the insulator on its side, grip it with padded pliers, and cut the offending part of the insulator off. This has already been done in the following picture:
Your insulator should end up like this:
Now you can enjoy the Rose with the draw it was meant to have.
This is the upper insulator:
The screw on the left side transfers current to the positive post. On the other side, there is a semicircular projection that hangs down well past the rim of the upper base. The upper base is screwed onto the lower base to form a single unit. The lower base has the exterior airhole. When the two are screwed together, the airhole may end up on the positive side of the upper base or the negative side (this varies between atomizers, not on a single atomizer). If it winds up on the positive side, all is well. This one, however, winds up on the negative side:
As a result, the airhole is obstructed by the insulator. If I turn on the flash, you can clearly see it:
I asked the guys at Eden Mods about this, and they said their CNC machines were not programmed to avoid this, since there’s space between the airhole and insulator and therefore air can still get around it. That’s true, but having experienced it both ways, I can tell you that the difference is significant. The draw on this Rose, pre-alteration and fully open, is about the same as it will be nearly closed post-alteration.
To fix the problem, insert a sharp pin against the right rim of the airhole and dig it into the insulator. This will mark where you need to cut:
Now use Mr. Razorblade to cut down through the projection. Do it at such an angle as to make sure both the exterior and interior airholes are unobstructed (the interior airhole is in the center of the insulator disc). Just beneath the blade you can see the beginning of an incorrect cut:
Now flip the insulator on its side, grip it with padded pliers, and cut the offending part of the insulator off. This has already been done in the following picture:
Your insulator should end up like this:
Now you can enjoy the Rose with the draw it was meant to have.
very clever...but also very unlucky...I don't recall reading about this problem elsewhere ..but thanks ..this is very useful indeed!
I'm going to check mine. My authentic has a tighter draw than my clones so I'm wondering if this is why.
Just shy of one year ago I posted about putting that notch in the Rose, also open the center hole just a tad, it really did help a lot.There are two posts here with pics, 2nd and 3rd post on this page. Rayon wick, better flow, flavor, saturation and Nic Hit!
Last edited:
Sorry that I never saw those posts as I don't use Rayon...good to know I'm not the only one however.
Got a Rose V2 s clone. Really like it, still seeking out the best flavor builds.
The drip tip though does get very hot. Does anyone else experience this?
The drip tip though does get very hot. Does anyone else experience this?
No, but maybe you're asking for more power than the airflow can give? I chain vape these babies and it only gets hot in the sun.
What's your build? And it could be that you're placing the coil a tad bit higher than should be. Can you show us a pic?
Sent from my iPhone using Tapatalk
- Status
Similar threads
- Locked
- Locked
