- Status
Skate board grip tape... comes in all sort of colors... could cut thin strips and do stripes or polka dots... would take minutes to apply gives grip wet or dry....
Just had another thought, non-slip bath tub decals....
No sanding, spraying, or drying required for my ideas... Just cut, peal, and apply......
Just had another thought, non-slip bath tub decals....
No sanding, spraying, or drying required for my ideas... Just cut, peal, and apply......
I'm in LOOOOVE I followed AMG's directions and so far no leakage and vapor euphoria!! Thank you everyone for your posts and help! And since this is my 1st mod, it will always be the most special to me!!
Wanna sell it?
I got my 1.8 BF attys today. Can someone point me to the priming instructions please? I seem to recall something about a soak.
Since these atty's don't have stale icky primer in them to get rid of, some have opted to put several drops in the atty & let it sit for a bit---vertical!!
This primes the atty & some kind of magic science stuff--- Guru's will have to explain more!
This primes the atty & some kind of magic science stuff--- Guru's will have to explain more!
Capt., prime the atty well with lots of juice (put the atty in a condom cover) and let it sit to soak into the mesh. How long? See if you can hold out for 1/2 hour, LOL. (Good luck. I had to physically remove myself from the room.) Then don't forget to prime from the top and bottom when you have it on the VMOD. (per AG )
)
Capt., prime the atty well with lots of juice (put the atty in a condom cover) and let it sit to soak into the mesh. How long? See if you can hold out for 1/2 hour, LOL. (Good luck. I had to physically remove myself from the room.) Then don't forget to prime from the top and bottom when you have it on the VMOD. (per AG
I can see with this one where self-control issues come into play. Thanks for the info. I'll put them in the kitchen while the ballgame is on.
Also, I've been running Boba's & Gorilla Juice with no issues through the cartos. I'm not going to run into any with the attys am I?
Hey everyone! I need a new carrying around mod, my Old Goat 3.7volt just isn't holding up to the abuse it takes in my pockets. I really like the Vmod, I especially like the cone that protects the atty/carto at the connection. I have read that a new chassis is coming out for the vmod, will it represent a major improvment? Should I wait to order until the new chassis comes in? Also, for those of you that use it as your main carrying around mod, how well does it hold up? Thanks!
I received an email this morning and the new chassis will be available next week...
@Capt L you will have no probs vaping Bobas in the Vmod using a bf hybrid atty...thats what I've been vaping nonstop
since I got my Vmod and since the hybrids first came out...still using same 1.5 hybrid atty....
@Capt L you will have no probs vaping Bobas in the Vmod using a bf hybrid atty...thats what I've been vaping nonstop
since I got my Vmod and since the hybrids first came out...still using same 1.5 hybrid atty....
I have to say, I'm impressed. The attys make a huge difference. I actually like it better at 3.7V. Very good flavor. It definitely has a place in my arsenal. I may need to get it a silver companion.
I haven't had either of mine crack.
Brian said it was a hit & miss thing.
If yours does crack, it'll be replaced.
I've been carrying one around for over a month & it's great. I've dropped it & no problems. It's been in & out of my pocket hundreds of times. I have a pet care service & drive at least a hundred miles per day & am in & out of the car at least 25 times a day. It's perfect for my busy day.
- Status
Similar threads
