- Status
@chopdoc I may have bribed the prize bot with a case of Royal Purple 
I learned something tonight. Was working and grabbed my Snow Wolf with the TFV4 on it and took a couple drags off it then put it in my shirt pocket. Kept on working and finally reached a stopping point where I could take a couple minutes break. Pulled that Snow Wolf out of my pocket and took a few hits off it, sipped some water, took a few more drags and was relaxing a bit. Took a few more and noticed the Snow Wolf was pulsing when I was vaping on it. Vaped it some more and sure enough, its pulsing. Looked at it and im vaping at 200 watts!!! WOW. Flavor was good and the vape wasnt bad at all. I was tired because its been a long night but I couldnt believe I was vaping the tri coils in the TFV4 at 200 watts and it was vaping just fine. I turned it back down to where I usually keep it, around 90 watts but I am amazed it will handle that much power.
Hit my "Vape in the Fort" event yesterday. MUCH better layout than the one earlier this year - held outdoors at our downtown Headwaters Park. Still a touch disappointed that there weren't more hardware options. I'd guess 70% of the vendors were juice-only, and those vendors who had hardware didn't have the things I was looking for.
I walked up to one vendor and spotted a Velocity (I have two coming from an online order) and asked if it had the bottom-feed pin. The guy looked at it and said, "it has an adjustable pin". He looked bumpuzzled when I told him I had a bottom-feed mod and wanted the juice to flow from the bottom into the RDA.
However, I met a few guys, all sporting Velocities (using as regular RDAs), but they were more than happy to show me how they were coiled up and let me take some hits. I'M SO EXCITED!!!!!! Now I REALLY can't wait for mine to show up.
I walked up to one vendor and spotted a Velocity (I have two coming from an online order) and asked if it had the bottom-feed pin. The guy looked at it and said, "it has an adjustable pin". He looked bumpuzzled when I told him I had a bottom-feed mod and wanted the juice to flow from the bottom into the RDA.
However, I met a few guys, all sporting Velocities (using as regular RDAs), but they were more than happy to show me how they were coiled up and let me take some hits. I'M SO EXCITED!!!!!! Now I REALLY can't wait for mine to show up.
I finally found my ideal setup: a Kbox set at 20W or a mech mod, with either an RDA with a .8 ohm (single or dual) coil or a Kayfun 3.1 set up at 1.1 ohms. An Orchid v4 with a .7 ohm coil build (the lowest I'll go) is OK with high VG juice if I want to blow a few extra clouds.
I tried building my coils at .5-.6 ohms and found the vape was too warm and the juice tasted a bit burnt.
I tried building my coils at .5-.6 ohms and found the vape was too warm and the juice tasted a bit burnt.
I have an Orchid V4 and never could get it to not leak. I think my last build on it was .4 and I had it on a Tesla Invader II and the flavor was great yet it got hot fast (unregulated mod with dual 18650's) and I burnt my hand a few times as soon as the juice started pouring out of it. I bought the Orchid V7 thinking they finally fixed the leaking problem but nope, it also leaked.
KBox with Kayfun 3.1 (Top Fill Cap) 1.2 ohms and 20W. The KBox is an excellent APV that does the job perfectly.
I like the Sig Mini setup!!KBox with Kayfun 3.1 (Top Fill Cap) 1.2 ohms and 20W. The KBox is an excellent APV that does the job perfectly.
I have a couple Orchid V4 and a couple V5 and don't have leaks. The way I build and test them is to turn it upside-down and hold my fingers over the air-holes, take a long, strong pull on the drip tip and absolutely no air or juice should come through. This will also give the proper vacuum to the tank to prevent dripping.
Last edited:
The Sig mini is an excellent little mod as you know.I like the Sig Mini setup!!
It works with everything I throw at it, flawlessly.The Kayfun V4 is amazing as well, if you don't have one yet pick one up for $20, you can't go wrong.
Kayfun V4 Clone by Tobeco
- Status
Similar threads
- Locked
