Tips Needed For Making Coils

[kkiet]

Purchase a ohm meter, Do just a easy basic coil first. I learned by watching many youtube videos, If I can do it, you can. good luck. Keep us posted.

 

[MzLuscious]

I bet you did!

Haha

 

[Ou2mame]

Haha

Why does it sound so dirty when things are done at night lol

 

[MzLuscious]

Why does it sound so dirty when things are done at night lol

Not sure but its funny lol

 

[Jake287]

When installing and adjuting your coils use the same sized bit or screwdriver you wrapped them on to hold your coil in place while tightening the contact screws. If you've watched any videos, you'll see a lot of people doing that; makes life easer. I a gree with everything else said so far, ohm meter, coil master, etc. Good luck and have fun

 

[MzLuscious]

When installing and adjuting your coils use the same sized bit or screwdriver you wrapped them on to hold your coil in place while tightening the contact screws. If you've watched any videos, you'll see a lot of people doing that; makes life easer. I a gree with everything else said so far, ohm meter, coil master, etc. Good luck and have fun

Thank you! So far so good!

 

[Tmebs]

Best tip would be to use a tool ( coil master/kuro) and steam engine for correct wrap info....
Then wrap 2 additional wraps... With needle nose pliers pull 1 wrap off from each leg.
Tightens and kinda straightens that first and last wrap if that makes sense.

 

[Ou2mame]

I use micro screw drivers because they have that edge on the handle and it makes it easier to make bends in the lead to position it towards the air holes... At night.

 

[Aceman12]

They mostly come at night ... Mostly

 

[MzLuscious]

They mostly come at night ... Mostly

LOL!

 

[MzLuscious]

I use micro screw drivers because they have that edge on the handle and it makes it easier to make bends in the lead to position it towards the air holes... At night.

Night time is the best time!

 

[Ou2mame]

Night time is the best time!

I'm pretty sure it's the only time

 

[MzLuscious]

I'm pretty sure it's the only time

I think so too.

 

[MzLuscious]

Best tip would be to use a tool ( coil master/kuro) and steam engine for correct wrap info....
Then wrap 2 additional wraps... With needle nose pliers pull 1 wrap off from each leg.
Tightens and kinda straightens that first and last wrap if that makes sense.

I ordered a coil master a day ago and I can't wait to get it!

 

[Aceman12]

That was an ALIENS reference in case I look like weirdo. Wicking is the biggest performance variable especially if you get the coiler. Get some Japanese organic cotton. Also I vote for 26 gauge kanthal. It sounds scarier then it actually is.

 

[Ou2mame]

26g is my go to, unless I'm bored and feel experimental then I play with the 24g. 28g i leave for my flavor drippers for dual micro coils.

 

[MzLuscious]

That was an ALIENS reference in case I look like weirdo. Wicking is the biggest performance variable especially if you get the coiler. Get some Japanese organic cotton. Also I vote for 26 gauge kanthal. It sounds scarier then it actually is.

So far I have everything just waiting for the coiler.

 

[Maurice Pudlo]

Don't coil drunk or w/o glasses if you require such things!

Serious advice right there.

 

[MzLuscious]

26g is my go to, unless I'm bored and feel experimental then I play with the 24g. 28g i leave for my flavor drippers for dual micro coils.

What are your fav drippers?

 

[MzLuscious]

Don't coil drunk or w/o glasses if you require such things!

Serious advice right there.

LOL!