Zenesis Informational/Help thread. Please Post questions and answers here.
- Thread starter applefr3ak
- Start date
- th_trl_thread_readers 0
- Status
How is the flavor? If it's good, I wouldn't mess with it. Sounds like your juice is pretty thin so opening it up like a straw may flood and cause problems.
Ok.... so I'm still going nuts trying to figure out what's wrong with my standard. Ever since getting it I have been having problems with misfires. I did most of the suggestions from the posts, like sanding the screw, spring. When I take the switch apart I five the screw a light sanding. I stretch out the spring, a tiny bit, then reattach.
The unit fires up great! I get a bunch of vapes out of it all very consistent. Then it starts misfiring. At first, ts like 1 or of 3. Then, it goes to 1 out of 2. Next thing I know, it won't fire at all, until I take the switch apart and repeat step 1.
From the previous suggestions, i f/u with Jason who kindly sent me a new spring but I'm having the same issues so it can't be it.
Has anyone experience this and/or knows how to fix it.
Thanks!
The unit fires up great! I get a bunch of vapes out of it all very consistent. Then it starts misfiring. At first, ts like 1 or of 3. Then, it goes to 1 out of 2. Next thing I know, it won't fire at all, until I take the switch apart and repeat step 1.
From the previous suggestions, i f/u with Jason who kindly sent me a new spring but I'm having the same issues so it can't be it.
Has anyone experience this and/or knows how to fix it.
Thanks!
I would try putting an extra washer under the switch screw, see if that helps any.
The flavor is very good. I'm still getting occasional dry hits, after going through 3 tanks of juice on a new wick and coil.
Do you know the size/dimensions of the washer? While working on it in my garage I dropped it and it's lost : (
vMason, I have an email in for the dimensions for you however if anyone has the spec's feel free to chime-in
No, I sure don't. What I would do is go to a hardware store and find one that will sit inside of the switch body where it's supposed to go. If you had that washer and lost it, that would explain your problem, though.
Dear Andy,
How long is the average time a mod spends in Mike's hands waiting for repair?
Thanks,
Forgotten Hippie on the Plains
How long is the average time a mod spends in Mike's hands waiting for repair?
Thanks,
Forgotten Hippie on the Plains
What repairs were being done? And i know he was out of town most of last week.
Unfortunately, I was having problems before losing the washer. I haven't used it since.
Just picked up my Zen Mini today def too airy of a draw for me as of now but nonetheless it's tasting .....en!...is there anyplace I can get a top cap with a smaller air hole?
Orion 2.1, 69 Mod with Cobra Atty, 28ga Kanthal, 5/6 wrap.
def too airy of a draw for me as of now but nonetheless it's tasting .....en!...is there anyplace I can get a top cap with a smaller air hole? Orion 2.1, 69 Mod with Cobra Atty, 28ga Kanthal, 5/6 wrap.
Just picked up my Zen Mini today
Orion 2.1, 69 Mod with Cobra Atty, 28ga Kanthal, 5/6 wrap.
There were a few, but they have been discontinued. Most people decided they preferred the open draw after a few days. You could put a piece of stainless steel tape over the air hole and poke a smaller hole in it with a 20 or 18g needle to test out a tighter draw if you want. There is a tutorial around by Lorderos on how to carefully superglue a piece of blunt 18g needle in the airhole - but I remember it was tricky and easy to screw up . . . .
Oh, and CONGRATS on the Zen mini!!!
There were a few, but they have been discontinued. Most people decided they preferred the open draw after a few days. You could put a piece of stainless steel tape over the air hole and poke a smaller hole in it with a 20 or 18g needle to test out a tighter draw if you want. There is a tutorial around by Lorderos on how to carefully superglue a piece of blunt 18g needle in the airhole - but I remember it was tricky and easy to screw up . . . .
Oh, and CONGRATS on the Zen mini!!!
Thanks! Very interesting! I'll have to search that up
Another question if I may...I thought the switch was magnetic? Mine has a spring? I just found this out 5 min ago...not sure how I feel about this...Orion 2.1, 69 Mod with Cobra Atty, 28ga Kanthal, 5/6 wrap.
Or am I thinking of the Macaveli?!
Orion 2.1, 69 Mod with Cobra Atty, 28ga Kanthal, 5/6 wrap.
Orion 2.1, 69 Mod with Cobra Atty, 28ga Kanthal, 5/6 wrap.
The Zenesis use to have magnets but many many people complained of misfires cuz with the magnets the switch needed to be pressed in and to the side, many couldn't master this technique. All Zens ship with springs now dayz and there is no need to push in and to the side....it will fire everytime with the spring. I believe you can still get the magnets at houseofhybrids.com when in stock.
Ah ok! I don't feel so weird now haha I thought some parts may have been left out or something...I want it to operate at its maximum potential. I'm sure you guys know where I'm coming from.
Orion 2.1, 69 Mod with Cobra Atty, 28ga Kanthal, 5/6 wrap.
Cool deal
I am very familiar with them...used to order my DSE 901 & Yeti 510s from them. Orion 2.1, 69 Mod with Cobra Atty, 28ga Kanthal, 5/6 wrap.
- Status
Similar threads
- Locked
- Locked
