These tests below only note my personal ESTIMATED ratings for the batteries I tested at the time I tested them. Any battery that is not a genuine Samsung, Sony, Murata, LG, Panasonic, Molicel, or Sanyo can change at any time! This can be one of the hazards of using “rewrapped” or batteries from other manufacturers so carefully research any battery you are considering using before purchasing.

Misusing or mishandling lithium-ion batteries can pose a SERIOUS RISK of property damage, personal injury, or even death. Never use them outside of a fully protected battery pack and you use them at your own risk. Never exceed the battery’s true continuous discharge rating (CDR), never let it get colder than 0°C or hotter than 60°C, and keep the plastic wrap and top insulating ring in perfect condition. Never use a battery that is physically damaged in any way.

Testing batteries at their limits is dangerous and should never be attempted by anyone who has not thoroughly studied the dangers involved, understands the risks, has the proper equipment, and takes all appropriate safety precautions.

If the battery has only one current rating number, or if it only says "max", then I have to assume the battery is rated at that current level for any type of discharge, including continuous.




Test Results
It’s been 4-1/2 years since I last tested this cell so I thought it was worth seeing if the performance has changed over the years. This version of the 30Q has a “6” in the lower left corner of the printing on the wrap. If there is no “6” then it is not a 30Q6.

The 30Q6’s I tested performed a little better than the 30Q’s I tested in 2018. You probably won’t notice the difference but it’s good to see.

The datasheet and presentation document mentions operation at 20A (not a rating!) and a maximum cell temperature of 75°C but I recommend not using it at over 15A. This is an “energy” cell and not a “power” cell and you start getting a lot of voltage sag when running near its 15A rating or higher. The cell already reaches over 70°C when run at 15A continuous so 20A operation would have to be non-continuous.

Two cells tested out to 3075mAh and 3089mAh, which is good consistency. As expected for cells from a major manufacturer both cells easily exceeded their 3000mAh rating. I have not tested the cycle life of these cells.

These were purchased for testing by me from 18650BatteryStore (18650 Battery Store - Lithium Ion Batteries, Chargers and Accessories).


18650 Ratings and E-Scores Table:
https://www.e-cigarette-forum.com/blog-entry/18650-battery-ratings-table.7447/


20700/21700 Ratings and E-Scores Table:
https://www.e-cigarette-forum.com/blog-entry/20700-21700-battery-ratings.7827/


Continuous Current Discharge Graphs



Ratings and Performance Specs Graphic


I want to work for the community full time! If you feel what I do is worth a couple dollars a month and you would like early access to battery availability, battery testing and news, and a say in what I test, then please consider becoming a patron and supporting my testing efforts: Battery Mooch is creating battery and device tests | Patreon.

To see how other cells have tested check out this link: https://www.e-cigarette-forum.com/forum/blog-entry/list-of-battery-tests.7436/

Try the all new Beco Pro Disposable Vape at vape shop. The Beco Pro Disposable Vape is a box style pod device that requires no maintenance due to it's simple and disposable nature. The Beco pro features no buttons and is automatically activated when you inhale. Estimated to last up to 6000 puffs the Beco Pro is pre-filled with 12ml of TFN-based e-liquid in a 50mg nicotine level and is available in variety of flavors. Each Beco Pro is designed with a 650mAh rechargeable built-in battery. Perfectly designed for the best vaping experience on the go the Beco Pro Disposable Vape is also equipped with a 1.2ohm Mesh Coil and 2 and airflow control options for the best vapor and flavor satisfaction.

Specifications:
Dimensions: 76.5mm x 45.8mm x 20.9mm
Built-in Battery Capacity: 650mAh
E-Liquid Capacity: 12ml

Beco Pro Features:
1.2ohm Mesh Coil Design
Disposable Design
(2) Airflow Control Options
No Maintenance Required
Classic Automatic Style
Vape Pen Design
Ultra Lightweight and Compact Design
Non-Refillable Design
50mg Tobacco-Free Nicotine E-Liquid
Flavors by Beco



You can get more information about nicotine free vape at: https://www.bbb.org/us/ca/tustin/profile/ecigarette-liquid/vapesourcing-1126-1000099548

Illuminate any room with the brand new Hyde Retro RAVE Edition. The Retro RAVE is a rechargeable disposable device that features an LED Light that can be turned on or off with the quick click of the button, discreetly located on the bottom of the device.


FLAVORS:

• Aloe Grape – Aloe | Grape
• Bananas & Cream – Banana | Cream
• Blue Razz Ice – Blue Raspberry | Menthol
• Brazmallows – Blue Raspberry | Marshmallow
• Cola Ice – Cola | Menthol
• Energize – Energy Drink
• Loops – Fruit Cereal | Milk
• Minty O’s – Sweet Mint | Menthol
• Morning Brew – Coffee | Cream
• Peach Mango Watermelon – Peach | Mango | Watermelon
• Philippine Mango – Yellow Mango
• Pina Colada – Pineapple | Coconut
• Power – Green Energy Drink
• Sour Apple Ice – Green Apple | Menthol
• Strawberry Banana – Strawberry | Banana
• Strawberry Kiwi – Strawberry | Kiwi
• Summer LUV – Fruit Medley
• Tropical – Tropical | Gummy
• Blue Razz Clouds (NEW)
• Dragon Fruit Lemonade (NEW)
• Mango Peaches & Cream (NEW)
• Peach Lemon (NEW)
• Rainbow (NEW)
• Strawberry Lemon Lime (NEW)
• Watermelon Ice Cream (NEW)

FEATURES:

• 5% Nicotine
• Liquid – 12mL
• Battery – 400mAh (Rechargeable)
• Rechargeable via Micro USB (Not Included)
• 5000 Puffs Per Device

Wotofo Zetta 5000 Disposables Review



Wotofo are back again with a new disposable vapes line: the Zetta 5000!

These devices were sent to me by Wotofo for review purposes (thank you, Cara!).

In the past year or so, it has seemed like that new disposable e-cigarettes or even new manufacturers of it crop up on a daily basis. There’s sooooo many of them now, and “old school” vape hardware producers have gotten in on the action too. Some have even formed subsidiaries or sister companies that appear to be dedicated to the design the product of disposable vapes.

Wotofo have released a fair few, and I have had the privilege of reviewing some of them. The Zetta 5000 though is a bit different from their other disposable vape offerings and indeed from its competition too, and we shall dive down into what the Zetta 5000 is all about in this review.

My review will be from my own experience of using these devices in everyday life as a regular vaper.

Quick specs:

- 108 x 29 mm. It’s a short and fat cylinder, basically resembling a sausage!

- 550 mAh battery

- Made from aluminium alloy and food-grade PC.

- Having a 1.2 ohms mesh coil with nexMESH Tech.

- A generous 13mL of e-liquid volume, and claims to have a 5000 puff-life (hence the “5000” in the name).

- Has a USB-C port for charging at its bottom.

- Available in 12 flavours and in various nicotine levels.

Kidding aside with the sausage likeness, its form factor is actually very comfortable in the hand. All surfaces are smooth, from the mainly plastic shell to the metal bottom. There is a unique, almost splashed, design printed all the transparent shell, and underneath this outer shell you will find the branding in the usual big Wotofo font plus the flavour name on the side.



The transparent shell also serves to enhance the LED lighting effects that feature on the Zetta 5000. These LED lights illuminate when vaping and also when charging. The LED pattern is that of flashes of changing colours all around the device, with the flashing speed not too fast or too slow. It is also not too bright to call out unwanted attention; so all in all, quite a quirky addition to an already pleasing-to-the-eye device.

The mouthpiece is of a flat shape that is very comfortable on the lips. And the charging port at the base of the device does mean that you cannot charge this upright, but it does charge quickly enough so that it won’t be on its side for too long.



With the battery size, e-liquid capacity, and having actual metal components to it, it is quite understandable that the Zetta 5000 weighs a tad heavier than your run-of-the-mill disposable vapes. But that’s not to say it’s heavy- you won’t really notice its weight when pocketed.

It’s a simple pull and puff type of device which is very responsive. It doesn’t have any airflow control or other extra features for customisation which makes for easy operation. The draw from it is a medium MTL draw in my opinion, giving a surprisingly warm-ish vape despite the high resistance coil installed.



Of the available flavours of the Zetta 5000, I have been sent these: Watermelon Ice Cream, Watermelon Cantaloupe Honeydew, Grape Ice, Mango Ice Cream, and Blueberry Raspberry Ice. They all taste quite nice, with punchy flavour and strong sweetness. One thing I did notice, particularly with the Watermelon Cantaloupe Honeydew, is that in some puffs, the vape can feel a little “dry”. Maybe that’s just me, but it’s not really a con for me as it doesn’t happen consistently enough.

Otherwise, the fruit-based flavours taste of fresh fruits, intensified by the added juiciness and sweetness. The Ice Cream flavours really do have a milky base to the taste which mixes nicely with the fruit component.

All in all, the Wotofo Zetta 5000 is a decent disposable e-cigarette which gives a very satisfying vape. It offers a good selection of flavours and is very easy to use, especially on-the-go. With its relatively high e-liquid capacity and recharging capabilities, it makes for a cost-effective solution for avid users of disposable vapes (but please always dispose of your used vapes responsibly!).

My sincerest thanks again to Wotofo for allowing me to review these products!

Kumiho V (5) // Review by HyDrOpOnIc1987

Hello and thank you for stopping by to read another review by, well uh, me of course! Today's device is the Kumiho V or 5 and was sent to my by Health Cabin for the purpose of a fair and honest review. I'm hoping to showcase just that in today's review. First I'll show some promotional images and then tell you about the features and specifications of this device. Lastly, I will unbox, assemble and use this device and tell you the highlights of my time with this device. So without further adieu, let's get to it.

Promotional Images, Features, Specifications and Contents of Box













Features:
1. Build-in 600mAh battery
2. 2ml refillable empty transparent pods: 0.6ohm & 1.0ohm
3. Patented coil cotton design for 0.6ohm pod for quick eliquid transmission
4. Innovative vibration interaction when the pod connected
5. Super easy to use with auto draw
6. Adjustable airflow for accurate RDL & MTL vaping
7. Pre-filled pods are also available, sold separately
8. USB C charging port

Specifications:
Brand: Kumiho
Unit: 1 Set
Materials: Aluminium Alloy, PCTG
Size: 119mm*22mm*11.5mm
Color: Black, Blue, Red, Gunmetal, Pink Gold
Battery capacity: 600mAh
Output wattage: 18W max
Pod capacity: 2ml
Pod resistance: Meshed 0.6ohm(14-18W), Dual Coil 1.0ohm(11-13W)
Package: Box

Contents of Box:
1pc Kumiho Model V Device
1pc Model V Empty Pod 0.6ohm (14-18W)
1pc Model V Empty Pod 1.0ohm (11-13W)
1pc User Manual

Unboxing, Assembly and Usage Highlights:





The packaging for this device is actually pretty nice. It’s a box, obviously, but has a paper sleeve over it which is red and stylized. Kumiho, the branding, is embossed in gold. There’s the picture of the device, but also the model name in a glossed font along the right side. Pretty stunning, but red is my favourite colour.

On the left side of the sleeve it says Model V in the same glossy font. The back of the sleeve has all the pertinent information: a description of the device and is use, 6 “icons” and their explanations describing the features of the device, the package contents, the contact information for the brand and last but not least is a warning to “KEEP OUT OF REACH OF CHILDREN”. Oh, and also that it’s made in China.

The box itself is pretty plain. White with the brand and model name in beige font. Tada.
Inside the box is where everything lives. There’s a sleeve that houses the manual, a spot to write down your purchasing information for warranty purposes, as well as more of the same information about the device itself. Then in the box you have the device and 2 pods, one 1.0 ohm and one 0.6 ohm.

Because it’s a pod device, I didn’t have to go wash it with soap and water and a tooth brush, I just used a sanitizer wipe and then wiped it off with a moist paper towel. Now that the mouthpiece is clean, I put my eliquid in the pod. The pods have a silicone plug that you have to pull out, and its on the side but near the bottom of the pod. In the 2 weeks I’ve had this device though, it hasn’t had a leak an the plug has held strong after multiple refills. Also, the hole is big enough that air can pass by the side of the nipple thing on my 60ml and 120ml chubby gorilla bottles, so that’s a definite plus. Zero issues when filling. I let the pod sit for about 20 minutes, just to be safe.



When i put the pod in, there was a vibration. Haptic feedback. And the pod clicks into place pretty satisfyingly. It has 2 magnets, but there are also a couple notches that link into place and clicks along with the vibration to let you know it’s seated properly.



On the side of the device is a little switch or lever and it controls the airflow. To be honest, I didn’t feel too much of a difference between it full open and full closed. It is not really a MTL device. I guess it can be, but its VERY airy. The draw was almost the same from both pods as well. The only difference I really noticed was in the way the liquid flowed through the pod. Weirdly enough, I found that my 50/50 10mg salt nicotine liquid would flood the 1.0 ohm pod very quickly, while when I used 70/30 6mg freebase liquid in the 0.6ohm pod, it couldn't keep up. I emptied and put the same flavour of salt nicotine liquid in the 0.6 ohm pod and it still had a hard time keeping up. I had to make sure to take at least 20 second breaks between toots, sometimes more. The way these pods behaved made me wonder if they were perhaps mislabeled and should have been reversed? I don't know lol. But I did get the 1.0 ohm pod to work well with freebase nicotine liquid. The flavour and vapour production was amazing and on point. I just wish they behaved properly and that the 0.6ohm coil would work right at all.
The restriction on the draw is identical between the pods. If you set the airflow and switch between the two, it will seem the same unless you have different liquids in them. The battery on the device lasts quite a while though, it took me 3 full days of use to kill it. So that is DEFINITELY a plus. The device is fairly nice looking but it also can't stand up right, the bottom, which it where the charge port is, is rounded (probably to protect the port) and wont let it stand up. It will fall to either side when you try to stand it up right.

The device is pretty awesome when the pods work as they should. I hope that they work on the 0.6 ohm pod some more and perhaps check to see if the pods were mislabled and reversed.

I would like to thank Health Cabin for sending me this device to review. It’s a very nice device if you stick to the 1.0 ohm pods. I would recommend this device to those who like a restricted DTL pod with minimal airflow control.
Here is a link to pick it up from Health Cabin.

Kumiho Model V Pod Kit

Thank you for reading this review, I hope you found it informative and somewhat pleasant to read. Hope you all have a good one, and try to stay out of trouble if you can. But a little trouble is fun! 

Cheers!

I'm looking for a black ASMODUS Colossal 80w mod.

I dropped mine and a few days later it wouldn't turn on. I took the batt out and checked it's voltage. It was .6 volts. I thought the batt just went bad and put in another fully charged one. After 3 or 4 puffs an error message appeared on the screen ... something like "temperature too high". Yep it was. In that short a time I could feel the bottom of the mod become very warm.

Popped the batt out and retried ... same result. So I'm hoping to find a replacement.

If this is the wrong place to ask please let me know where to post. Thanks

Currently Using

XL Smileomizer
6 ml capacity
single vertical coil
2.5 ohms
5 volts
V4L Zeus 1300 mAh battery
KR808 thread

Have a supply of XL Smileomizers that I would like to be able to use.

I need to find a replacement system since Vapor 4 Life is gone.

Hi All,

Getting the closet of vape gear cleaned out. Bought this as a backup and barely used for about a day before it went back into the box.

Excellent box mod, with a great reputation. Works flawlessly.

$200 + free shipping to the US only.

Please see the pics attached below.

Hi, today let's take a look at the Freemax Maxus Solo 100W Kit. I will examine each of the characteristics that distinguish this item in this Test. I hope that by the end of this reading you may have understood this product, and therefore decide whether to invest in it or not. As always, my opinions are free and based on my personal experience.
• Enjoy the reading.

► Freemax Maxus Solo 100W Kit; Before starting let's see together some special features indicated by the manufacturer:
• FM Chip 3.0
• Fullspectrum LED lights
• Slide Switch to lock / unlock the device
• Output 5-100W
• Multiple Battery Compatibility
• Choice of various output modes
• Tank with child safety system
• Top Filling
• Adjustable airflow
• New Double Mesh Coils FL



► Freemax Maxus Solo 100W Kit; Packaging:
The cardboard has a black background on the front and rear. The remaining sides create a broad spectrum multicolored effect. On the front we find a stylized image of the kit, the color of the sample, the Freemax brand, the name of the product, some main features in the form of icons and the general warnings on Nic. On the back of the package are exposed; specifications, content and more warnings on Nic.



On the long sides of the box you can see; the scartch & Check, and a barcode containing also a small image of this kit. Also you can read; the name of this device, and various warnings. You can also see the social networks where FreeMaxtech carries out its sales promotion, and also the legal logos & trademarks.



► Freemax Maxus Solo 100W Kit; Packing List:
• 1 * Freemax Maxus Solo 100 W Mod
• 1 * Freemax Fireluke Solo Atomizer
• 1 * pre-installed 0.15Ω FL1-D Mesh Coil
• 1 * 0.2Ω FL2 Mesh Coil
• 1 * 5ml glass tube
• 1 * USB Type-C Charger
• 1 * 18650 Battery Adapter
• 1 * Extra Silicone Oring
• 1 * Warning Card
• 1 * Warranty Card
• 1 * User Manual
• 1 * Desiccant sachet


► Freemax Maxus Solo 100W Kit; Specifications:
• Size: 28.8 * 42.8 * 90mm
• Weight: 123g
• Output voltage: 0.7-7.5V
• Input voltage: 3.3-4.2V
• Output power: 5-100W
• Output mode: Watt (Normal, Sport, ECO) / VPC / Bypass / TC-NI / TC-TI / TC-SS316 / TCR
• Resistance range: 0.1-3Ω
• Battery: Single external 18650/20700/21700
• Charging specification: 5V / 2A

● Fireluke Solo Atomizer (Coils Platform FL):
• Size: φ28 * 50.35mm
• Capacity: 5ml (2ml TPD)
• Thread: 510
• Drip Tip: 810



► Freemax Maxus Solo 100W Kit; Available colours:
• Cobalt Blue
• Black
• Sea Blue
• Golden
• Gun Metal
• Red

I received the Cobalt Blue version from FreeMax which is really my favorite if I had to buy it. However, I must say that all the other colors are also interesting, in particular I like the black and red versions.



► Freemax Maxus Solo 100W Kit; First Impressions:
Maxus Solo is a recent Mod by Freemax with a strong and sturdy zinc alloy frame, overall though, Maxus Solo turns out to be quite light. It's not a big mod, but it's not super small either as it can accommodate a single battery (21700, 20700 or 18650) and can deliver up to 100W. Maxus Solo also features VPC, Bypass, TC and TCR modes. The Maxus Solo Boost circuit is indispensable and necessary for the proper functioning of the Mod when the battery level is low. The Mod features LED lighting on the front and back of the device. These LEDs can be set in a variety of ways with an incredibly broad spectrum of colors and choreography. Of course, the lighting can be completely deactivated by making only the display visible.

The new Fireluke Solo tank (paired with the Maxus Solo Mod) uses Freemax's new FM COILTECH 5.0 with dual mesh SS904L and tea fiber cotton, and remains compatible with the excellent Coils FM COILTECH 4.0 platform.
The Fireluke Solo tank has a tank capacity of 5ml (2ml TPD) with the dual slot adjustable airflow. When it comes to DL vaping performance, Freemax is the gold standard for their amazing coils, both for flavor and durability. You can't go wrong choosing Freemax coils and tanks as they are consistently on top. I am currently having a lot of fun with both the updated Fireluke Tank and the Marvos CRC Pod Tank which is installed on the Marvos X 100W Mod which I will talk about very soon in an upcoming review.



► Freemax Maxus Solo 100W Kit; Screen and control keys:
The screen surrounded by LEDs extends over the entire front profile of the Mod. The transparency of the screen allows you to see the chip. Of course, if you are not a fan of the LED and its many settings, you have the option to turn it off and you can only view the background of the display with one of the six basic colors. Also on the Display you can rely on a complete set of information. The FIRE key is located at the top, slightly protruding and rectangular in shape with a longitudinal dividing line in the center, the same design is reserved for the "+ and -" adjustment keys which are located at the bottom and above the Type-C charging port .



Maxus Solo also implements the Mod lock function through a sliding button positioned on the side, this button may seem trivial, because you can lock the keys while continuing to vape, or you can turn off the Mod with five clicks before putting it back in your pocket. Actually the Mod lock slide button can come in handy when you want to quickly turn off the LED lights to show them when you decide to vape to you and all your nerdy friends. It seems to me an intelligent management to be able to turn off the lighting both momentarily and quickly using the button, or totally through the setting. Deactivating the LED certainly saves battery energy, for a longer vaping autonomy.



► Freemax Maxus Solo 100W Kit; The menu offers the following options:
● These are the main operations you can perform with this device. I hope the following pointers can help you understand how this product works.
• Key lock / unlock: Press and hold the “+” and * - ”buttons for 1 second simultaneously
• Device lock: Slide the side switch down to lock. At this point, regardless of the key pressed, the message "DEVICE LOCK" will always appear on the screen. Move the switch up to unlock and access the main interface
• Output mode selection: Press Fire 3 times to enter setting status and click Fire again to enter mode setting; press the "+/-" buttons to choose Power (Normal, Sport, ECO) / VPC / Bypass / TC (SS316, NI, TI) / TCR, (TCR 1, TCR2, TCR 3);
• VPC Power Setting: Switch to VPC in the mode state, Press Fire to confirm and press "+/-" buttons to choose. Press and hold Fire for 2 seconds to exit. After setting, the real-time curve output will be shown on the screen when vaping
• TCR Setting: Switch to TRC on the mode status, press "+/-" buttons to choose TCR 1, TCR 2 or TCR 3. After confirming the secondary mode, move the cursor to the TCR value option and press Fire to enter the adjustment interface
• Firing Wattage Setting: In TC mode, move the cursor to the wattage option and press Fire to confirm the selection, then press the "+/-" buttons to adjust
• TC mode resistance lock: In TC / TCR mode, press "+/-" buttons to choose resistance option in the upper right corner, then press Fire to enter and use "+/-" buttons to choose LOCK / UNLOCK
• Activation / deactivation of the automatic coil test: press and hold fire and the "-" button at the same time for 1 second to access the SETTING menu, or press Fire 3 times to access the setting status, then select the SETTING option to access ; Select COILTEST option in SETTING menu, press "+/-" buttons to turn on / off.
• Timeout setting: Select TIMEOUT option in SETTING menu, press "+/-" buttons to set from 5s to 15s (default timeout limit is 10s)
• Theme Color: Select THEMECOLOR option in SETTING menu, press "+/-" buttons to change theme color.
• Turn on / off the LED light: Select the LED ON / OFF option in the SETTING menu, press the "+/-" buttons to turn on / off
• Change LED color and effect: Select LED CONTROL option in SETTING menu, press "+/-" buttons to choose LED color and effect.
• Switch Temp Unit (° C / "F): Select the ° C / ° F option in the SETTING menu, use the" +/- "buttons to choose
• Puff Reset / Time Reset: Select the PUFF RESET / TIME RESET option in the SETTING menu, press Fire to reset the counter
• Factory data reset: Select the RESET option in the SETTING menu, press Fire to restore factory settings; Or press and hold Fire and the "+/-" buttons at the same time for 3 seconds.



► Freemax Maxus Solo 100W Kit; Side and rear profile:
The frame entirely surrounds the Mod, the metal is thick and sturdy and looks like it can withstand everyday wear and tear. The clear part surrounded by the LED lights extends from panel to panel, so the back is also clear with a design that allows the LED lights to shine incredibly powerfully. My mon photographs do justice to these super bright highly scenic LEDs.





► Freemax Maxus Solo 100W Kit; 510 thread and bottom base:
The gold plated pin is spring loaded and is positioned in the center at the top of the Mod. The Tank Fireluke with its 28.5mm diameter is perfectly housed on the Mod. In the lower part of Maxus there is an arrow indicating the opening direction of the door to insert or remove the external battery.



► Freemax Maxus Solo 100W Kit; Battery compartment:
By opening the flap you can insert a 20700, 21700 or 18650 battery with the adapter included in the kit. The indications for the battery polarity are found on the inside of the flap. This system is my favorite for inserting a battery, this is flawless, closes securely and meets my expectations.



► Freemax Maxus Solo 100W Kit; Tank Fireluke Solo:
For this test (TPD version) Freemax was kind enough to send me a 5ml convex Pyrex glass for my Fireluke Solo. Refueling is child-proof and this system is great for their safety. The top cap opens after lifting it and sliding it following the arrow indicating the opening direction.



The Fireluke Solo Tank adopts a replaceable 810 Drip Tip, moreover the tank is completely removable to facilitate cleaning operations. The coils are inserted from the bottom and after having unscrewed the base. The base houses an adjustable AFC system with a rotating ring with end stops. The two opposing slots are wide to allow a deep DL vape. If you turn the ring and close the buttonholes you can instead get a tighter and very precise adjustment for your RDL vape.



► Freemax Maxus Solo 100W Kit; Coils and Vaping Test:
Fireluke Solo is compatible with Freemax's FM COILTECH 4.0 platform but of course also with the new pre-installed FL-D COILTECH 5.0 with double Mesh.
The composition of both Coils included with the Maxus Solo 100W kit is of military grade Mesh SS904L with tea fiber cotton.

• Pre-installed 0.15Ω Mesh Coil FL1-D Range 50-80W:
Lately i triggered my new Coils (only the big ones for DL) with a rather original method, tying them with a thread and immersing them completely in the liquid bottle for 10 seconds. I must say that with this method I feel good and I don't waste time. Then I slightly dry the outside of the coils and put it in the tank, then I fill the tank with e-liquid and wait about 10 minutes. Starting to use the FL1-D Coil I start at 40W and slowly increase the power up to 50W, then I start making longer puffs with my strawberry 70/30 e-liquid. The first Puffs (50W) are clean and free of weird flavors, but the results in terms of flavor and vapor are already impressive. I decide to try all the powers up to reach 80W with the airflow completely open and the results are more monstrous. I must say that at 80W the heat begins to be felt even if it is not excessive, so I find my weak point at 65W and I continue to enjoy my strawberry with enormous satisfaction. Testing the RDL style it seems that even at low wattages from 40 to 50W the coils work well, are responsive and taste great in combination with an open AFC setting of 50% or even less.

• Mesh Coil FL2 0.2Ω Range 50-80W:
As before I used the same strawberry e-liquid and started vaping the same way as before: Starting at 40W and reaching 50W to start taking longer hits. At 50W the flavor and vapor start to be nice and without weird flavors. So I try all powers up to 80W. The test produced results very similar to the previous FL1-D resistance, but with slightly less intense and full-bodied flavor and vapor (for the same Watt). With this Coil I found my weak point by setting 55W of power with the AFC ring open for 40/50%.





► Freemax Maxus Solo 100W Kit; Final conclusions:
The Mod Maxus Solo with the many advanced functions it possesses might seem difficult to set up, in reality it is simple and it does not take much time to learn. The display offers a complete overview of information and settings. Some people might argue that all those lights are annoying and useless, others will love them and be impressed. In any case, you can always turn off the LED.

The flavor and vapor of FL Coils are really hard to beat! Freemax continues to produce high-level innovative products with evident results for all to see. I don't think you will be disappointed if you buy one of these kits.

Thanks to Freemax for sending me this sample for review.
Maxus Solo 100W Kit | FREE MAX. FLAVOR MAX.

Thanks for reading.

CLICK HERE TO SALT BAE 50 DRIP PRO DISPOSABLE DEVICE (6500 PUFFS)

Specifications:

• Tear Drop Shape Design
• Rubber Finish Grip
• E-liquid Capacity: 13ml
• 6500 Puffs Approx
• Draw Activated Firing Mechanism
• Mesh Coil Heating
• Integrated Rechargeable Battery - Type C Port
• 50mg (5%) Strength

LABOR SALE IS LIVE NOW!!!!!!!!!!!
USE COUPON CODE (LABOR15) TO GRAB 15% DISCOUNT STOREWIDE

Hi ECF,

Hope you had a lovely weekend! It's Monday and hope this giveaway of Innokin Klypse Gradient colors can bring you Monday energy

As the most popular product of Innokin recently, Klypse has been received large compliments so we bring the new colors of Klypse for you!

Come & Enter this giveaway to get your favorite color of Klypse!



How to enter:
1. Visit Klypse - Vape Kit | INNOKIN® for more information about new colors of Klypse.
2. Comment what is your favorite color below to win one of 6 New colors of Innokin Klypse vape kits. The colors from left to right are:

• Sunset
• Violet
• Chartreuse
• Gold
• Peach
• Phantom

We will randomly choose the winners on August 29th.

Thank you so much for your support for all these time and wish you all the best lusk

Best regards,
Innokin Team

Dear wholesale customers,

The August is coming to an end. So here comes Healthcabin new round of brand discount – August brand discount round 2 for you to save more on different vape-brand products.

Take the chance to join us while offer lasts~

Promotion Details

• Discount: 1.5%-3% OFF for selected 10 hot brands
• Date: 22nd – 28th Aug, 2022(-0600 GMT)
• Wholesale ONLY
• No coupon code required, total discount amount can be found at your shopping cart.

Promotion Brands



With any questions, please feel free to contact your account manager.

Please view the August Brand Discount – Round 2 here.

The best mag 18 mod has received a lot of attention from various users since its launch, and I believe that it is not only noted for its great looks, but also for its powerful performance. Here we have to mention the MAG 18 mod.


Powered by dual 18650 batteries and with a maximum power of 230W, this is the best vape mod kit in terms of output which features a capacity that cannot be ignored.

And the built-in advanced IQ-X Chip provides Bypass, TC and Power Modes for the unit. The Power Mode allows you to adjust between 5 and 230W.

Paired with a 0.96-inch TFT Display on the side allows you to view the data more clearly. With the 510 thread, a tight connection to the smok uk TFV 18 Tank is also possible.

If you want a product that will last and give you a great vaping experience, the mag 18 mod is an absolute must.

You can also choose your favourite from them:
best rpm5 smok
best voopoo gt 2

Uwell Caliburn KOKO Prime 15W Pod System Kit equipped with the same compact size as the original Caliburn KOKO, made of lightweight and durable PC+ABS materials. Powered by a built-in 690mAh battery with a larger capacity and uses a faster and more convenient Type-C port, which can be fully charged in less than an hour with a 1.6A charging current. Uwell Caliburn KOKO Prime refillable pod cartridge has a 2ml capacity with a top filling design.


Parameters:
Size:68mm x 45.6mm x 16mm
MaterialCTG, PC+ABS
Capacity: 2ml
Wattage Output:15W Max
Battery :690mAh Built-in
Coil Resistance:UN2 Meshed-H 0.8 Ω (Sold Separately) / 1 Ω(Pre-installed)


Features:
-Draw-Activated Firing Mechanism
-LED Indicator Light
-Interchangeable Decorative Panels
-USB Type-C Port with 1.6A Fast Charging
-Compatible with Caliburn G Pod & Coils
-Fashionable Lanyard to Free Your Hands
-1.6A Type-C Fast Charging
-Ingenious Dual Airway Design

You May Also Like The Following Items:
Candy King Air Disposable Vape - 6000 Puffs
Flum Vapor Float Disposable Vape - 3000 Puffs
SWFT Mod Disposable Vape - 5000 Puffs

Smok Rainbowbar disposable pod.
Has an LED light that will light up when puffed.

VOOPOO Argus MT Kit

Argus MT Kit comes with 3000mAh built-in battery, 6.5ml capacity and 5V/3A type-c fast charging. Designed with IP68 rating tri-proof function (water-proof, dust-proof, drop-proof), it is loyal accompany fearless of any extreme environment or scenario. And the unique volcano crater structure is added for leakage proof and airflow improvement. The two-way airflow will bring you an easy deep DL vping by reducing 60% airflow loss. Powered by GENE.TT 2.0 chip, Argus MT can provide multiple modes, such as Smart, RBA, Turbo and TC. There are no needs for you to worry about accidental igniting or switching in your pocket with QS lock button. VOOPOO Argus MT Kit is equipped with Maat Tank New that is compatible with all TPP coils, features top filling system.

Details:
1. 100W max power, 6.5ml capacity
2. IP68 rating tri-proof function: water-proof, dust-proof, drop-proof
3. Ingenious crater leakage proof structure
4. GENE.TT 2.0 chip, QS lock
5. Built-in 3000mAh battery
6. 3A Type-C fast charging port with dust-proof cover design
7. Holeless appearance, lanyard ring design
8. Two-way airflow brings easy deep DL vaping
9. Easy top filling design
10. Multiple modes: Smart, RBA, Turbo and TC
11. Compatible with all TPP coils
12. BMS real-time battery protection
13. Safety protections: Overtime/Low Battery/Overcharge/Output Over-current/Short-circuit/Over-heating Protection




VOOPOO Argus MT Mod

Argus MT Mod comes with 3000mAh built-in battery, 5V/3A type-c fast charging. Designed with IP68 rating tri-proof function (water-proof, dust-proof, drop-proof), it is loyal accompany fearless of any extreme environment or scenario. Powered by GENE.TT 2.0 chip, Argus MT can provide multiple modes, such as Smart, RBA, Turbo and TC. There are no needs for you to worry about accidental igniting or switching in your pocket with QS lock button.

Details:
1. 100W max power
2. IP68 rating tri-proof function: water-proof, dust-proof, drop-proof
3. GENE.TT 2.0 chip, QS lock
4. Built-in 3000mAh battery
5. 3A Type-C fast charging port with dust-proof cover design
6. Multiple modes: Smart, RBA, Turbo and TC
7. BMS real-time battery protection
8. Safety protections: Overtime/Low Battery/Overcharge/Output Over-current/Short-circuit/Over-heating Protection

Here we introduce a new mod member of Lost Vape QUEST – URSA NANO PRO pod system kit.Lost Vape Ursa Nano Pro is a GAME CHANGER, a Top-tier level Pod System featuring 25W max output.The first to bundle both integrated coil & changeable coil system in one kit set.

Features

• Glossy Anodized Pastel Gradient Dual-tone coating

• 2.5ml Vape Juice Capacity

• Compatible With Both Integrated Coil and Replaceable Coil

• Step-less Adjustable Airflow

• For MTL, Loose MTL, and RL Vaping

• Fit For Nic Salt and Freebase E-juice

• Internal 900mAh Battery

• 9-25W Output Range

• LOST VAPE QUEST Chip

• 0.42” OLED Screen

• Triggered by Both Auto Draw and Manual Fire

• Short-Circuit Protection / Weak Battery Protection / Over Heat Protection

Newcomer friendly yet not forgetting user experience for advanced vapers.The bundled 0.8Ω (changeable system) is designed for MTL & Salt Nic users, and the 0.6Ω (integrated system) supports Loose MTL ~ RL range for the freebase community.You can now experience two systems in one device. Be sure to check out the fascinating Glossy Anodized Pastel Gradient Dual-tone CMF and it's Breath-Pulse Trigger LED.

Please go to vape store near me to make an order.

You may also like:

dotmod revo
smok nord 2 kit price

VOOPOO will invite 10 friends to be VOOPOO Product Reviewer and VOOPOO Brand Promoter! If you want to spark your life with VOOPOO, just join us !


You will get

1. The newest products of VOOPOO for free

2. Birthday and festival gifts


We need you

1. Post your review of VOOPOO product and information of VOOPOO activities on this forum and other social media.

2. Actively reply to the posts of VOOPOO official posts.


If you wanna join us or get more details, please DM me or email freya@voopootech.com.


Just join us and make your vaping more wonderful with VOOPOO!

What is Naked 100 Menthol Berry vape juice at vapesourcing.com? Berry by Naked 100 Menthol is a mix of sweet and tart berry flavors that'll be sure to leave you craving more and more of this vape juice. With every puff of Naked 100 Menthol Berry, you'll taste the flavors of a blend of sweet and ripe blueberries, raspberries, blackberries, and ice-cold menthol, making for an incredible mixture you'll love to add to your collection. Berry by Naked 100 Menthol comes inside of a large 60mL bottle and comes in multiple nicotine strengths, including 0mg, 3mg, 6mg, and 12mg, assuring you'll have enough choices for a smooth and enjoyable vape every time.

best vape juice Very Cool by Naked 100 Menthol takes freshly picked blueberries, blackberries, and raspberries, flash freezes them, blends them, and drizzles a little bit of honey on top. Very Cool is as amazing as it sounds, with a sweet and tangy profile layered with refreshing notes of ice.

Specifications:
Primary Flavors: Menthol, Blueberry, Blackberry, Raspberry
Manufacture: USA Vape Lab
Brand: Naked 100 Menthol
Nicotine Level: 0mg, 3mg, 6mg, 12mg
VG/PG Ratio: 70/30

naked very cool Features:
60mL Glass Bottle
Dropper In Bottle
65% VG
35% PG
Made in USA
Available nicotine: 0mg, 3mg, 6mg, 12mg



Recommended products:
best tobacco e juice
fruit vape juice

Zovoo Cubebar 600 Disposables Review



With thanks to Zovoo/Voopoo (thanks Fiona!), I am pleased to present to you, lovely lot, the CubeBar 600!

Yes, it is another iteration of a vape disposable, but having tested so many by now, I can tell you that not all of them are made equal. And we shall have a look at what the Zovoo CubeBar600 brings to the table in this review, after my use of them these past weeks.

Quick specs and features:

- Dimensions at 96 x 18 x 18 mm. It’s small and shaped kind of like an olive oil bottle with a very short neck!

- 400 mAh battery.

- Appears to be made from PC and PCTG.

- Having a 1.5 ohms coil.

- 2 mL of e-liquid capacity and I suppose the “600” in the model name hints towards a 600-puff life, which is typical of a 2mL capacity disposable vape device.

- Available in 10 flavours per Zovoo’s website.

The device comes in stylish and colourful packaging with loads of information printed around the outer box including device specs, manufacturer information, and of course the flavour! Surprisingly, this device comes with a user manual inside the box- something I rarely see with disposables.

It is mainly made of plastic which makes it very lightweight. The brand and flavour are printed in front, and its bottom has an LED light that activates when vaping and lights up when battery becomes low. It’s simple and straightforward, free from extra features such as airflow control or ability to recharge the battery.

The device shell itself has a vertical stripe design going on that appears to be underneath the outermost plastic coating, and this adds a little more flair to its looks. The mouthpiece is fixed but is quite comfortable, as it narrows a little from the device body but then flares out towards the tapered top.

It’s comfortable in the hand, easy to slip inside one’s pocket, and is very portable making it an ideal carry device.



From a performance point of view, I have to say that the CubeBar 600 actually surprised me a little! The auto draw is very responsive, delivering a smooth and quiet vape. But there were two things that really stood out for me with the CubeBar 600 against most disposables I have reviewed, and that is draw tightness and draw warmth. In terms of tightness, it’s akin to almost a tight MTL that is amazingly close to that from a cigarette. I’m really impressed by that!

Now, most TPD (read: 2 mL capacity) disposables I’ve tried are often cool on the vape, perhaps to maximise puff life whilst preserving the battery as much as possible. Not the CubeBar 600, as this one actually gives a decent and warmish MTL vape. And for someone like me, that warmth just adds a little extra to the satisfaction I want to achieve when vaping. The vape just really hits the spot for me!



I was sent five flavours to try, namely: Cola Ice, Blood Orange Ice, Honeydew Ice, Pineapple Mango, and the quite unique Ginger Lemonade. These were pleasant to vape, with dense flavour and actually not dry-tasting unlike some disposable on the market. Although they all have a touch of cooling in them, the “ice” feeling doesn’t overwhelm the taste or main favour notes which is always a pro. They all tasted as I expected, but truth be told I wasn’t sure what to expect of the Ginger Lemonade having never vaped this type of flavour before. Well, surprisingly it was actually quite nice and refreshing! It kind of tastes like a sweet soothing lozenge you might pop in when you’ve got a sore throat. Don’t get me wrong, it doesn’t taste like medicine, rather a strong lemonade sprinkled with mild ginger taste. I quite liked it!

Final Thoughts:

I would happily recommend the Zovoo CubeBar 600, no question about it! For those that use disposable vapes, or vapers wanting an easy back-up device, and most of all for smokers wanting to switch to vaping, you can’t really go wrong in choosing the CubeBar 600. It will satiate your nicotine and MTL draw cravings (regarding the draw cravings, ex-smokers will know what I’m talking about).

My sincerest thanks again to Zovoo/Voopoo for allowing me to review these products!

Hello,

I have the Smok P3, and I read it was updatable, but I haven't found a way to check and/or do this. Can someone point me in the right direction?

Also, I've noticed a few issues. It's supposed to be dust/water etc proof, except I've had to tighten down my 510 pin at least 3 times. I know juice has gotten into the battery compartment a few times. Plus the rubberized sleeve has actually separated from itself in places. Are these common issues? I love the form factor of this mod, since I have carpal tunnel and get the dropsies often.