Sourcemore sent me the Uwell Whirl T1 Pod Mod Kit for the purpose of this review.






The Whirl T1 is a draw activated pod mod that is so small and simple, it’s almost perfect for anyone who is trying to quit smoking via vaping. Charge it, fill it, vape it. It doesn’t get any easier than that.



All you get in the box is the pod mod with the UN2 meshed-H .75 ohm refillable pod already installed, a warning card, and a user manual. There is no charging cable in the box, so I checked Sourcemore’s description, and it says one will be provided separately. I didn’t receive one – not a problem for me, as I have a couple of them – but it could be a problem for a new vaper. I can imagine how easily these could be mailed out or sold at shops without the cords, and someone would be opening the box at home with no way to charge their new gear. I have a lot of nice things to say about this pod, but this needs to be addressed before I’ll recommend it.



The pod holds 3 mls of liquid, and is filled through a tiny port in the bottom – see the red silicon. I’m not a fan of the bottom fill, especially when there is plenty of room on top of the pod for a port. But so far it hasn’t leaked. On the back, there’s an air flow adjuster, and it closes down to a nice MTL, opens to a decent restricted DL. It’s better than I expected, really. It clips into the mod securely with a tiny ridge around the inside of the mod and minuscule tabs on the pod. Tabs is perhaps not the right word, more like little nubs. Put it this way, they don’t stick out enough to break off, and I’m sure they’ll hold up just fine over the life of the pod. I’ve been pulling the pod repeatedly and so far they’re not even phased.

The air flow adjuster - slide to the right for open, left for closed.


Why am I pulling the pod so much, you ask? Of course to fill it, to see how those nubs hold up, and to adjust the air. But also because that’s how you adjust the power setting. Both the mod and pod are triangular in shape, and the power output is changed by spinning the pod. On the screen, one arrow lights up for 14 watts, two arrows for 15 watts, and three arrows for 16 watts. I love this. There’s no way to accidentally change your power output.



Before use, pull that blue safety tape off. The fill port is visible in this picture, but sorry, I could not get a good shot of the numbers. If the fill port aligns with the screen, the device is on its lowest setting. If II, it's on medium, III is for high.



The mod has a plastic bottom and screen, with an aluminum wrap around the body for durability. The battery is 1300 mAh, and charges on the bottom with a C type charger. That’s another thing I’m not a fan of. The shape of this mod means it stands up nicely, why would you want to lay it down to charge it?



The .70 ohm pod gives good flavor and reasonable vapor. The kit is small, light, and comfortable to hold, perfect for pocket or purse. Nice looking, too. It comes in red, light blue, grey, camo, dark blue and black.



Shown here in light blue.

With a few tweaks, this could be a really great kit. It works well, the flavor is quite good, it charges fast, it's durable and conveniently sized. Not a fan of the bottom fill, bottom charge, and no cable in the box, and for those reasons I likely won't be investing in any replacement pods.


You can buy this kit at Sourcemore for $17.10 with code WHIRK.



Thanks, Sourcemore for the opportunity to review the Whirl T1!

have three of the same,and gunk up one then rotate more evenly.the flavor will give up different notes. WHAT YOU GOT?

Is this raspberry doughnut eliquid from Amatorium any good?


Login to view embedded media

Dear Vape Friends,

Good day!

Here comes Healthcabin new round of giveaway in this brand new August, we’ve prepared something different. We are now partnering with both Wotofo & Hellvape to giveaway the SRPNT RDA & Fat Rabbit RTA, with 15 winners in total. Ends on 10th Aug. Are you ready to join us and test them for free? Take the chance!

*Prizes will be shipped out randomly if you are lucky to win!

About Wotofo SRPNT RDA
Meet the Wotofo SRPNT RDA, the upgraded new member in Wotofo Serpent family! Bold innovation in deck design that guarantees an excellent vape using 5mm ID Claptons. Besides 5mm ID coils, the deck is also structured to support 3mm ID coils for dual build. Accurate airflow control that offers just the right amount of airflow across the deck.



About Hellvape Fat Rabbit RTA
Fat Rabbit RTA is the newest RTA in Hellvape RTA series. It is fit for 510 Pin Device. Hellvape Fat Rabbit Vape RTA features 28.4mm diameter and 5.5ml capacity for beast vaping quality and massive cloud. The anti-condensation design with changeable 810 drip tip would improve your vape puff after puff. Dual airflow system offers various air intakes and flavors. Hellvape Fat Rabbit RTA adopts postless building deck to provide generous space for installing coil with ease. With quarter turn deck and top cap, you can install and fill e-liquid easily.



Join & Win
Finish the tasks below and win Wotofo SRPNT RDA & Hellvape Fat Rabbit RTA home easily. Good luck to you all!!

Please click here to join: HealthCabin Giveaway or August Giveaway | HealthCabin

Sourcemore 2021 Summer Sale

5 Rounds Mystery Box Flash Sale from $0.01
(Includes Fortis Kit, LUXE 80 Kit, Vinci Kit, Crown 5 Kit, and so on)

[/url]

10% OFF SITEWIDE Coupon: SUMMER
(Sale page, clearance and weekly deal items excluded)

Bronze Level Exclusive 5% OFF Coupon: SUMMER5
(Must log in, sale page, clearance and special discounted items excluded)

Sale Time: Aug. 2nd~Aug. 11th

Enter here<<<Sourcemore 2021 Summer Sale

Imbued with XROS DNA , the Vaporesso XROS MINI Pod Kit is the newest member of XROS Family. Vaporesso XROS MINI provides the best MTL vaping experience. With its compact size and 1000mAh built-in battery, the XROS MINI allows you to be on the go for nearly 2 days without recharging.
• Updated 1.2Ω pod
• 1000 mAh Built-in Battery
• Diamond Pattern Design
• SSS Leak-Resistant Technology
• Top Filling System


Quick Links:
Vaporesso XROS Mini Replacement Pod Cartridge 2ml
Vaporesso XROS Replacement Pods 2pcs

Updated XROS Pod
The 1.29ohm pod delivers MTL vaping experience.
The XROS pods are compatible with the whole XROS family.

Long Lasting Battery
The 1000mAh built- in battery provides a significant improvement for the XROS MINI and can support nearly two days of vaping.

Sss Leak- Resistant Technology
The SSS Leak Resistant Technology has been proven to work effectively in previous VAPORESSO pods.
Lock the e-liquid inside firmly and prevent from messy leakage.

Diamond Pattern Design
The luxury diamond pattern surface gives it a prestigious look.
Great non-slip and overall feeling in-hand.

Refined Curve Base
The 150° refined curved surface made by diamond high-gloss cutting process.
More comfortable, smoother to hold.

Convenient Top Fill
Extremely easy to refill your e-juice with the top filling style, only one hand required

Draw Activation
Auto draw to start a vape, totally easy to use

Battery indicator
Triple colors for 3 power levels, know your battery enough well

TYPE-C Charging
1A Type-C quick charging，fully charge in less than 60mins

Yachtvape Eclipse RTA is a collaboration between Mike Vapes and YachtVape. Single coil RTA was designed to be a small stealthy RTA that creates great flavor. Here are some of the key features.
Recurve style build deck with smooth honeycomb airflow.
Liquid capacity with straight glass is 2ml and 3.5ml with bubble glass.
24mm diameter RTA.
Color choices: Stainless Steel, Matte Black, Gunmetal, Matte Stainless Steel, Gold and Rainbow.


4 SLOTS POSTLESS DECK EASY BUIDING
Eclipse RTA is perfect for both counterclockwise and clockwise coils, without coil adjustment, prevent coil out of shape and spit back
HIDDEN HORIZONTAL HEXAGON SOCKET SCREWS, SUPER EASY TO SCREW

SUPER DEEP HONEYCOMB INTAKE STRUCTURE
THE STRUCTURE WILL PROVIDE SUPERIOR FLAVOR

FAST JUICE FEEDING
SHORT WICKING TUNNEL PROVIDE FAST JUICE FEEDING AND GOOD FLAVOR,PREVENT DRY HIT

As we all know, pen-style vape kits pair a tank or pod cartridge with a battery, which has a tube shape, look similar to a pen, making the vape device simple, portable and versatile. Freemax has released four types of vape pen style kits so far - Marvos T 80W, Twister 30W, Gemm 80W, and Twister 80W. As for you, which one do you like best?



Here is some information about these four vape pen kits produced by Freemax:
Freemax Marvos 80W Pod Mod Kit = Marvos DTL Pod 4.5ml + Marvos T 80W 3000mAh Built-in Battery
Freemax Twister 30W Vape Pen Kit = Fireluke 22 Sub Ohm Tank + Twister 30W 1400mAh Twist-style Battery
Freemax Gemm 80W Vape Pen Kit = GEMM Disposable Mesh Tank + 3-Level Adjustable Wattage 2900mAh Built-in Tube Mod
Freemax Twister 80W Vape Pen Kit = Fireluke 2 Sub Ohm Tank + Twister 80W 2300mAh Built-in Battery VW Tube Mod

Hey guys. This time let's look at the Aspire Cloudflask S Kit. It is an update to the original Cloudflask Kit. So what have Aspire changed for the new version? Read on to find out!

The first big change is the material the mod is actually made of. The original was made of Stainless Steel whereas the "S" version is now Aluminium. Also, the size has changed with the height of the S being greater but the rest of the dimensions are smaller. As with the original, there is a 2000mAh internal battery and this is charged via the USB Type-C port at up to 2A charge rate. Output wise this still uses a By-pass output – basically, the output depends on the battery charge and will be higher with a fully charged battery and will drop as the battery charge decreases.

An LED indicator surrounds the fire button and this changes color to display the battery charge remaining. The ASP chipset provides plenty of user protections. There is a new coil added to the kit, this still has the original 0.25ohm Mesh coil but a 0.6ohm Mesh coil has also been added. Although the airflow of Cloudflask S is not adjustable the 0.25ohm coil offers a DTL vaping experience and the 0.6ohm coil is more of a restricted DTL. The pod is refillable by removing it from the mod and opening the fill port cover located on the pod base. For great vape Hot Summer Sale, you can check vapeourcing online shop.

Check for more details here: Aspire Cloudflask S Pod System Kit 2000mAh

You may also like:
bantam butterscotch
buy vaporesso xros

Dear Customers,

Hope you are doing well these days!

A brand new August is here. So Healthcabin is here to bring our new round August brand discount promotion for wholesale only, with 3% off for selected 10 brands. Take the chance to join us and save more on your favorite vape-brand products!

3% OFF Selected Hot Brands

• Discount: 3% OFF for selected 10 hot brands
• Date: 2nd – 9th Aug, 2021 (-0600 GMT)
• Wholesale ONLY
• No coupon code required, total discount amount can be found at your shopping cart

10 of our best selling brands listed below:

• VOOPOO
• UWELL
• INNOKIN
• VANDYVAPE
• DOVPO
• WOTOFO
• Horizon
• Eleaf
• HELLVAPE
• Yumi

With any questions, please feel free to contact your account manager.

Please view the August Brand Discount here.

Updated 2021 New Coupons on Vapesourcing

Coupon Code: Luxe2M
Coupon Price: $39.59
Discount: 25.29% off
Link: Vaporesso LUXE II Box Mod 220W

Coupon Code: GALK
Coupon Price: $38.99
Discount: 30.36% off
Link: Geekvape Aegis Legend Kit 200W with Zeus Sub Ohm Tank

Coupon Code: JObliK
Coupon Price: $31.99
Discount: 15.79% off
Link: Joyetech ObliQ Pod Kit 60W 1800mAh

Coupon Code: ArgusX
Coupon Price: $22.99
Discount: 32.36% off
Link: VOOPOO Argus X Pod Mod Kit 80W Single 18650 Battery

Coupon Code: KKPK
Coupon Price: $23.99
Discount: 17.25% off
Link: Kamry K1000 Plus ePipe Kit 1000mAh

Coupon Code: RZROK
Coupon Price: $6.59
Discount: 44.85% off
Link: Vaporesso Renova Zero Pod System Kit 650mAh

Coupon Code: ARCFOXM
Coupon Price: $33.49
Discount: 27.18% off
Link: SMOK ARCFOX TC Box Mod 230W

Coupon Code: ARCFOXK
Coupon Price: $48.99
Discount: 18.34% off
Link: SMOK ARCFOX Kit 230W with TFV18 Sub Ohm Tank

Coupon Code: AeglosK
Coupon Price: $23.99
Discount: 40.01% off
Link: Uwell Aeglos H2 Pod Mod Kit 60W

Coupon Code: Trident
Coupon Price: $28.99
Discount: 25.65% off
Link: Suorin Trident Pod Mod Kit 85W

Maybe it's just my lack of knowledge on the matter, due to the fact that I don't care enough to look it up, but based off of the emails that I've received from JUUL over the past few years, it just seems like they don't have an ounce of fight in them.

First it was the banning of all flavored pods, meaning 85% of their product line is just out the window. I was actually surprised they survived as a company after that happened, but I guess the buckets of money they were making before the ban helped out a lot. I know the law is the law, and it's not like they could just continue selling flavored pods, but I just didn't see any push back from them at all on the matter. From my point of view, they just folded and accepted the loss.

I know they've taken other hits after the pod ban, but again, specifics elude me. So, what sparked my interest in making this post was an email they sent out on April 20th of this year that I just now read...

"Final call - order before our online sales pause on April 22nd."

It basically reads something about federal regulatory changes...blah blah blah. So ALL online sales are just gone now. So does JUUL have people in the trenches actually fighting for the vaping community? I just haven't come across much proof, or rumblings in the media about them actually fighting for the many, many, many millions of dollars they have lost out on due to them taking huge L's left and right. I don't even use JUUL products anymore, so if you're wondering why I care so much about the matter, I'm wondering the same myself. It's just odd. I guess the parts of big tobacco who didn't own any shares in the vape industry finally got tired of losing money to it. Anyway. That's a rant.

Today,I wanna introduce you the Lostvape Ursa Mini Pod Kit uk.It has many variaties for you choose from.The appearence design of the kit is gorgeous and high-level.Let's check it out.

Lost Vape Ursa Mini Pod Kit SPECIFICATION
Body Material:Zinc Alloy & Stainless Steel
Dimension:30.7*26*107.22mm
Screen Pixel:0.69"
Power Range:5-30W
Pod Capacity:3mL
Battery: 1200 mAh Built-in Lithium Battery
Battery Voltage:3.0V-4.2V

Buy cheap Lostvape uk Ursa Mini Pod System Kit is a compact pod kit with all key features. Lost Vape Ursa Mini Pod Kit works with 1200mAh Battery with max 30W output and type-C charging. Ursa Mini Pod Kit is equipped with 0.69 inch OLED screen to show vaping data clearly. Lostvape Ursa Mini cartridge has 3ml capacity with bottom fill design. Ursa Mini Pod is compatible with UB Lite coils and supports airflow adjustment.

Don't miss it,please buy from best online vape store.

Quick Link:Lost Vape Ursa Mini Pod Kit 1200mAh 30W

I just tried the newest product from vaporesso, this is the successor to the previous vaporesso xros, smaller, bigger battery and new color
has 1000mah battery, automatic draw activation, pure mtl experience, 1.2ohm resistance
in my opinion this product is very small, compact and easy to carry anywhere
very tasty and long lasting flavour
used for more than 1 week no leaks at all
have many color choices
and most importantly battery life that can be up to two days without having to worry about running out of battery while on the go

I think this is the best product for pod system in 2021.. a must try product

I’m selling all ecig stuff I have, this Walnut Blok is also up for sale. I’ll ship it out total $30. Thanks!
paypal

Up for sale is a very lightly used Kayfun Lite 2019 version. I ran a couple of tanks of unflavored juice and decided it just isn't for me.

This buy includes one 22mm Kayfun Lite 2019 in standard silver, with the complete spares packs unused. I will also include the clear bell cap that changes the look of the Kayfun while retaining the 2ml liquid capacity, which is brand new and never used. Also included is the Dome conversion kit in Fire that doubles the capacity to 4ml and the matching Fire drip tip.

Package will ship Priority Mail to your USA location for free.

To make this quick and easy, I am willing to let this go for a great price of $60 total. Great deal for a great product.

Greetings everyone and welcome back for today's review of the LUXE 80 Kit from Vaporesso. These kits were provided to me from Vaporesso for the purpose of this review. Giving you a brief rundown of the LUXE 80 Kit prior to my review, the LUXE 80 has a internal 2500mAh battery with a wattage range of 5-80 watts and comes in 5 colors with the 5ml GTX Pod 26 and obviously uses tried and true GTX coils. I think when reading this review you will as surprised as I was with the LUXE 80's size, so without further ado let's get to know the LUXE 80 Kit features and some details on it prior to my review.


COLOR CHOICES









INCLUDED WITH THE KIT







SPECIFICATIONS





MAIN FEATURES


* Ergonomic Body Shape With Compact Design

* Long-Lasting Built-In 2500mAh Battery

* 0.96 Inch TFT Screen Integrated Aesthetic, User-Friendly Interface

* Sss Leak-Resistant Technology

* Compatible With The Triple-Silicone Version Of GTX Coils.

* Quick Snap-Top Filling System

* Airflow Adjustment

* Axon Chip with 0.001s Insta-Fire


COMPACT DESIGN





PERFECTLY SIZED







AXON CHIP





EIGHT SAFETY PROTECTIONS





TYPE-C 2A FAST CHARGING





EASY MENU SYSTEM WITH SMART WATTAGE FEATURE





FULLY ADJUSTABLE AIRFLOW





QUICK SNAP TOP FILL





SSS LEAK RESISTANT





COMPATIBLE GTX COILS INCLUDING ( RBA COIL )





ARRAY OF DAPPER COLORS





LUXE 80 KIT BREAKDOWN







FIRST IMPRESSIONS


The LUXE 80's came as most Vaporesso devices do in a box that slides out of a outer wrapper box showing the kit and having all the specifications and what's inside printed on the front and back. Inside you find the LUXE 80, 0.2Ω and 0.3Ω mesh coils along with a nice braided type-c charge cable all compartmentalized in their own section under a cardboard open envelope containing all your paper information. At first glance the size of the LUXE 80 pleasantly surprised me because I really thought it was going to be larger than it is. As you can see the LUXE 80 has 2 attractive sides to it, one being it's color side and the other being it's leather side with LUXE stamped diagonally across the top as shown below. I was sent the beautiful red and carbon fiber colors, both give off the appearance of them being 3D and when the light hits the red one a mosaic of colors just seem to come to life and sparkle.






Vaporesso used the Pod 26 from the Go 80 Kit on the LUXE 80 and I'm glad they did because it works very well and the top fill system used in it performs equally as well.

For those of you not familiar with the Pod 26 I'll explain it's method of top fill, opening the top cap is done with just a minute turn of the top cap, you must grasp the tank or it will just spin.

Once open and off you will notice a hole with a membrane on one side, that is your fill port that acts like a one way valve letting liquid in but sealing back up when the juice bottle tip is pulled out. On the other side is a very tiny hole that allows air to escape when filling keeping everything mess free.

The four magnets on the Pod 26 are some of the strongest if not the strongest for a pod connection, I really have to apply some force to remove the pod, the pod will not come off unintentionally. To adjust airflow simply line up the slots with the slots on the device and turn the pod in either direction.







Supplied in the kit are a GTX 0.2Ω and a 0.3Ω mesh coil, both coils are clearly marked and each one's mesh netting is slightly different with the 0.2Ω coil having just a bit more. Both coils produce a impressive amount of vapor and have great flavor, I think the 0.2Ω coil edges out the 0.3Ω coil in the flavor department but just barely, both are great coils. Using the 0.2Ω coil I was able to get 180 vapes at 48 watts, using the 0.3Ω coil I was able to get 231 vapes at 40 watts of power.





Vaporesso kept branding down to a minimum on the LUXE 80 with branding being on the leather portion I mentioned earlier and on one of the sides of the device leaving the LUXE 80 with a very clean look. The matt gunmetal finish of all the buttons blends and matches the body of the the Luxe 80 very well. The Pod 26 clear tank with black colored top cap bring the look all together. There's even a silver colored accent ring at the base of the proprietary drip tip.






The device sits flush on any flat surface without worry of it being knocked over with a bump into a table or desk. The only other spot of any other writing is the bottom that nobody see anyway. There are three battery ventilation holes on the bottom as well.





I will tell you another very nice asset the LUXE 80 has besides it's small size and attractive appearance is how lightweight the device is. Weighing only 136g makes carrying out and about a no problem task, it's not light enough for shirt pocket carry but in a pants pocket you barley notice it's there.

The business end of the device shows a bright and sharply defined color display screen that is easy to read, I do however wish the wattage number size could have been made just a bit smaller to allow the other information that's displayed to be just a bit easier to read at a fast glance.

The color display screen and layout used in the LUXE 80 is the same one used in the Swag PX 80, information is laid out very well and is from the top down and left to right.


DISPLAY SCREEN LAYOUT

* Battery bar

* Power mode - ( Wattage, Voltage, Smart Wattage )

* Wattage/Voltage ( depending on your power mod )

* Vaping animation graph

* Best wattage recommendation for coil

* Coil ohms

* Volts / Wattage ( depending on your power mode )

* Puff counter

* Seconds of last vape





The LUXE 80 provides a 2A fast charge utilizing a type-c charge port and has a very nice bonus that I really love and I hope continues on future Vaporesso devices, when charging the LUXW 80 you get a battery bar and percentage displayed on the screen showing it's state of charge but you also have a time until fully charged also displayed on the screen. Charging time from a completely dead battery takes about 1 hour and 35 minutes, mine always stopped vaping at about 13% and took under 1 hour to charge.





Having a internal 2500mAh battery in such a small package is really impressive, I've done so many reviews of devices in this size class category and most have 1500 to 2000mAh internal batteries and are larger in size, I just grabbed a couple of recent reviews devices I reviewed to show a comparison of size next to the LUXE 80. Although larger in size both devices on each side of the 2 LUXES have smaller capacity internal batteries.





I think this kit is a perfect starter for someone beginning their journey into vaping because of it simplicity to use and a menu system that's also easy to navigate. I also think the LUXE 80 Kit will be a popular choice for veteran vapers as well because of sharp looks, size, weight and performance.

You get a choice of 3 power modes but having a smart wattage mode that saves the user from inadvertently applying to much power to the coil that's installed is the preferred choice for me, also having a recommended wattage setting ( BEST ) really helps new vapers.

The LUXE 80 offers 3 color display choices ( THEMES ) that are blue, green and pink. I'll list the functions of the simple and easy menu system down below.


MENU


* 5 Presses of the fire/ power button turns the device on/off

* 3 Presses of the fire/power button locks adjustment buttons

* Hold both adjustment buttons down simultaneously to enter into the menu

* Once in the menu scroll using either adjustment buttons to your desired location then press the fire/power button to activate that selected menu item


LUXE 80 PROS

* Attractive

* Lightweight

* Compact size

* Bright color display

* 3 Color theme choices

* 3 Power modes

* 2500mAh internal battery - ( PRO & CON )

* Instant fire

* Strong pod magnets

* Great ergonomic hand fit

* Type-c

* Battery percentage & time until fully charged displayed

* Light branding

* GTX coils

* Great flavor & vapor

* Clear 5ml pod


LUXE 80 CONS

* 2500mAh internal battery ( CON & PRO )

* Wattage number could be smaller allowing other display numbers size to be increased


FINAL IMPRESSIONS


Well folks as you can tell I'm really loving the LUXE 80 in a very big way because of all the reasons posted above. One thing I really like with the red colored one that I received is how much it sparkles in direct sunlight, I was hoping for the blue colored one because blue is my favorite color but the red emits so many colors that have a sort of 3D effect I love it.

The hand fit is great as well as the feel of being a quality built device with no button rattle. With compact devices I always worry about the pod coming off while in my pocket or when I'm pulling it out of my pocket but the magnets on the Pod 26 are so strong some real force is needed to pull the pod off the mod so no worry there.

The top fill method of the Pod 26 works like a charm also being a mess free one as well. Looking at the Pod 26 you would not think that it could hold 5ml on the standard version because it's a shorter styled tank but yes it does which is another pro going for it.

I'm so glad that Vaporesso decided to use the GTX coils and Pod 26 in this kit because the performance proven GTX coils perform wonderfully giving a great flavorful vape with more than enough vapor.

As you can see in my pros and cons section of the review I listed the internal 2500mAh battery in both because some people prefer to use replaceable batteries while others like the simplicity of a built in battery. The 2500mAh internal battery will get you through the day using the 0.3Ω mesh coil but it falls just a bit short using the 0.2Ω mesh coil, that's where a replaceable battery would shine, but charging only takes 1 hour and 35 minutes on a fully depleted battery, under 1 hour was the norm for me. I'm hoping to receive the replaceable 18650 version ( LUXE 80S ) for comparison soon.

Vaporesso has another winner with the creation of the LUXE 80 Kit and I would recommend it as a great starter kit and not just a on the go device for veteran vapers but one that can be used as a all day device.

I would like to thank Milo and Vaporesso for providing the LUXE 80 Kit for the purpose of this review and I also hope this review helped anyone looking to purchase the LUXE 80 Kit.

THANK YOU
BIGBOB2322

Just got back into vaping. Haven't smoked cigarettes in 4 days. Looking to get into testing products and vape juices. Just got a new set-up. Will take pictures and put it in the comments. Please give me comments and recommendations. Thank you!

Proverbs 25:21-22
If thine enemy be hungry, give him bread to eat; and if he be thirsty, give him water to drink: For thou shalt heap coals of fire upon his head, and the Lord shall reward thee.


Sent from my iPhone using Tapatalk

I’m glad to be back yet again with another review for you. This go round I’ll be taking a look at the Digiflavor Siren MTL RTA V4 that was sent to me by Geekvape in order to provide a fair and honest review. I am somewhat familiar with the Siren series of rtas. I have used and still to this day use the Siren V1. I bought two of the Siren V2 when they came out but honestly didn’t care much for them. I also have a couple of the Siren V3 that were included with the Z1 SBS kits. I like the V3 well enough although felt like the flavor production was a little lacking. So here we are now with the V4. It’s really different looking compared to past versions and I have high hopes for this one despite it only having a 2ml liquid capacity. Let’s see how it goes.






WHAT’S IN THE BOX?

1* Siren MTL RTA V4

4* Feather Cotton

1* 510 Drip Tip

4* DIY MTL Coil

1* Spare Parts Pack






SPECIFICATIONS:

Size

22 x 51mm

Capacity

2ml PEI chamber

Thread

510

Filling

Top fill

Coil

Braided Coil(0.65Ω); MTL Fused Clapton(1.0Ω); MTL Fused Clapton(1.2Ω); MTL Clapton(1.4Ω)

Color

Gunmetal, Rainbow, SS, Black



FEATURES:

· 1. 2ml PEI chamber, leak-proof top filling design

· 2. GTA design deck, easy to build and trim

· 3. 22mm diameter, fit for 510 thread device

· 4. Semi-hidden AFC structure, precise airflow

· 5. Long/Short drip tip options, MTL vaping

· 6. 4 kinds of MTL coils for DIY fun













INITIAL THOUGHTS:

The packaging of the Siren V4 has an outer white outer sleeve with a red two part box underneath. The one that I received is the gunmetal version. Like I mentioned earlier, I have some experience with all three prior versions of the Siren RTA. I knew from seeing pictures before receiving the sample that it looked quite a bit different from prior versions with an almost invisible tank section and what appeared to be a very long drip tip installed on it. I tried both of the included tips but really didn’t care for either that much as you can see in the picture below that I have installed one of my own 510 tips.



The Siren V4 is 22mm in diameter and about 51mm in total length. It is an MTL tank like previous versions but is quite different in design. It has a PEI 2ml tank section and includes a spare glass tank. It has center located honeycomb airflow holes and allows the airflow to come up directly under the coil. It has a leak proof bottom airflow system and a semi hidden airflow control system. It really is quite different from other rtas in the Siren line.

What I’m going to call the front of the tank has the Digiflavor logo on the top section of the tank with the barely visible tank section below that and the airflow control below that. There are multiple holes and a red mark that allows you to keep track of where you have the airflow set. It’s a rather nice feature in my opinion. The top cap of the Siren V4 takes about two and a half complete rotations to screw or unscrew when filling. I’m not sure why they didn’t go with the usual ¼ turn opening especially with a 2ml tank. There are no seals attached to the top cap underneath. There are two seals on the inside of the tank opening. One in the center that seals around the center airflow tube and a second around the outside perimeter of the opening. The bottom of the tank has the usual branding on it and says DIGIFLAVOR on it.







The kit comes with four coils and four cotton threads which I thought was nice compared to the normal two coils that are included in most tanks. I chose to build with the 316 2.5mm coil since I’m not a big fan of Ni and always prefer 316 coils. I’m sure others will enjoy the included coils.

The build deck is a two post single coil GTA style deck. Once the screws are loosened, it allows you to insert the coil legs in the slots below and then tighten the screws down while holding the coil in place. I’m not going to lie. I struggled a little bit trying to install the coil with just my hands at first and then grabbed my coiling tool which made it much easier to hold the coil in place. I did push the coil legs inward while tightening each one just to make sure they were trapped in place. The cotton threads that were included were a perfect fit. I thinned the tails out quite a bit to make sure I wasn’t over stuffing the holes so it would wick well.




Yes the wicking above is a little messy but I cleaned it up before putting the tank together.


FINAL THOUGHTS:

I have to say that I was rather pleased with the Siren V4 MTL RTA. The redesign was a success in my opinion. I felt like the flavor production was much better than the previous two versions.

Although I didn’t much care for the included drip tips, I could see where the long one would come in handy if you wanted to use it on a side by side device like the Digiflavor Z1 SBS.

I felt like the Siren V4 is a quality designed and built tank that provided good flavor and with all of the different airflow options can fit most vapers whether they want a really tight draw or a loose MTL. I found myself running it about ¾ open since I like a fairly loose MTL draw. I really like the red dot indicator that lets you keep track of where you have the airflow set. The airflow control was tight enough to not let it move accidentally but loose enough to where it isn’t too hard to adjust.

One thing I didn’t really care for was the small tank section that makes it very hard to see the liquid level in the tank. I just got in a habit of removing the top cap to check the liquid level and that seemed to work well enough for me. So, would I recommend the Digiflavor Siren V4 MTL RTA for you? If you don’t mind a 2ml liquid capacity and want a small 22mm rta that provides pretty good flavor and has a versatile airflow control then yes I would.

I’d like to thank Geekvape and Allison for sending the Digiflavor Siren V4 MTL tank for this review and thanks to the readers that keep me doing reviews. Below is a link to the Digiflavor website if you’d like to investigate this product yourself.


S MTL RTA V4 - Digiflavor

Hi folks! I’m back today with the Geekvape Obelisk C tank that was sent to me by Geekvape for the purpose of providing a fair and honest review. The Obelisk C is a revision of a tank that you might remember called the Cerberus. I liked the Cerberus and have a few of them but haven’t used one in a while. I even went as far as to find an rba for the original Cerberus. The Obelisk C is a bit different and does not use the same coils as the original unit. I’ll talk more about that a little later but for now let’s take a look at the Geekvape Obelisk C sub ohm tank.





WHAT’S IN THE BOX?

1* GeekVape Obelisk C Tank
1* GeekVape S 0.25ohm Dual Coil (pre-installed)
1* GeekVape S 0.15ohm Coil (spare)
1* Spare Glass Tube 4ml
1* Spare Parts Pack



SPECIFICATIONS:

Capacity

5.5ml(bubble glass) or 4ml (regular glass)

Filling Type

Top filling

Coil

Single mesh 0.15ohm coil(80-90W), dual mesh 0.25ohm coil(45-55W)

Color

SS, Gunmetal, Black, Gold, Blue, Rainbow



FEATURES:

· 1. Tri-boosting flavor

· 2. 25mm base diameter tank

· 3. Tri-slotted bottom AFC ring

· 4. Adjustable airflow, top filling system

· 5. 5.5ml/4ml e-juice capacity

· 6. Adopts new GeekVape S series coil











INITIAL THOUGHTS:

The packaging of the Obelisk C tank was the familiar review sample with the outer sleeve that slides off with the two part box underneath that once separated exposed the Obelisk C tank and the spare glass sitting in a foam insert. Underneath the foam was a box which contained a second S series coil, and an accessory pack with a spare 810 drip tip, some o rings, and a 510 drip tip adapter.

The Obelisk C comes with two coils. There is a single mesh .15 ohm coil rated for 80-90 watts. The other coil included is a .25 ohm dual mesh coil rated at 45-55 watts. Both coils thread into the base of the tank and thread onto the airflow tube connected to the top portion of the tank rather than being a push in coil like we’re used to seeing. If you’ve read other reviews I’ve done then you won’t be surprised that I liked the .25 coil better. It is much closer to my normal vaping range. I liked it at 41.5 watts when running it on my shiny blue Legend 2. The flavor production was fantastic in my opinion. It took me a while to work up the courage to run the .15 coil. With as many devices as I’ve tested, I’ve never vaped at 80-90 watts. I got up to about 62 watts and that was it for me. It did produce a really thick and flavorful vapor but is just too warm and strong for me even using a 3mg liquid. I just don’t see myself vaping at this range in the future but know that some people do.










The tank comes with two low profile 810 drip tips that normally I would immediately change out for a longer one but decided to give this one a chance and it has worked out fairly well. The top cap has the Geekvape name on it and is a ¼ turn to open or close like many of the Geekvape tanks I’ve tried. On the bottom side of the top cap is a different kind of seal than what I remember being used on past tanks. It’s a fairly skinny seal that is near the edge of the cap to make a leak proof seal. Inside the top are two very large fill ports that can used to easily fill the tank with just about any bottle without having any kind of mess. The 5.5ml bubble glass comes pre-installed on the tank but there is also a 4ml straight glass included in the package. The base of the tank is 25mm and the total length of the Obelisk C tank is 43mm. The bottom of the tank has the Obelisk C name etched in it and the center pin on the 510 appears to be gold plated. On the side of the base are three 10mm airflow openings that allow a generous amount of airflow to the tank. With coils rated at 80-90 watts you’re going to need quite a bit of airflow.










FINAL THOUGHTS:

The Geekvape Obelisk is a great flavor producing tank using the new S series of coils. There may be some similarity to the original Cerberus tank but honestly it’s been so long since I’ve used one that I don’t really remember except that both were bottom airflow tanks. I was a little surprised that Geekvape made a new bottom airflow tank after releasing so many top airflow tanks.

I feel like Geekvape did a good job of covering the bases by including what I would call a mid-range coil at 45-55 watts that can be run a little lower if necessary and also a high wattage coil for those that like that 80-90 watt range. That’s just not for me. Nothing wrong with it but it’s just too much vapor and too warm for me.

It’s nice that it comes with the bubble glass already installed. I’m not really sure why there is a straight glass included. I’d much rather have a spare bubble glass. With the coils that this tank uses I feel like the extra 1.5ml capacity is needed unless you like refilling your tank fairly often. I guess that depends on how much you vape or how often.

I’d like to thank Geekvape and Allison for sending the Obelisk C tank with Tri-Boosting flavor for this review. A big thanks to you the readers also. Below is a link to the Geekvape website if you’d like to take a look around.

Obelisk C Tank | Obelisk | Geekvape – Pursue a Healthy Vaping Experience. Official Partner of Paris Saint-German

Hi, today with pleasure I present to you URSA MINI KIT which kindly Lost Vape sent me for free in exchange for my honest opinion.
So I will tell you about the small-scale version of the spectacular Ursa Multikit. But let's see first of all and based on the Presentation By Lost Vape what we can expect from this new Pod device ...

Vibrant Choices available:
• Choose the color combinations you prefer and that inspire you. Refuse to remain anonymous, your new kit can be more colorful and energetic, or sober and elegant.

Tiny, Lightweight and discreet:
• An extremely compact device that can be easily inserted into your purse / handbag, allowing you to enjoy vaping on the go or in your daily routine.

Fully adjustable airflow control:
• By having the choice of URSA MINI's (fully adjustable) airflow, you can appreciate your own custom setup for maximum indulgence.

Maximum Power 30W output:
• Find your ideal wattage and chase the perfect flavor when vaping with URSA MINI between 5 and 30W.

Ultrasensitive magnet connection:
• By adopting the simple bottom fill system on the 3ml magnetic cartridge, we have achieved the best aesthetics for the URSA MINI.

Built-in 1200mAh Battery:
• By equipping the device with the integrated 1200 mAh battery, we have done our best to combine compactness and practicality, URSA MINI is able to support a whole day of vaping.

Type-C Fast Charging :
• The URSA MINI Pod Kit has a built-in DC 5V Type-C port. Plug the Type-C cable into a power source, the battery icon will start animating and stop animating once charging is complete.

Enjoy the reading.



Ursa Mini Pod Kit; Packaging for reviewers:
When the courier handed me this package I thought; "it's big enough so it will be a big and heavy device", I was wrong! I noticed it immediately when I picked up the package and it was very light in my hand. Once unwrapped, I understood what it was, I really enjoyed receiving a new device from the prestigious Lost Vape company.
For obvious reasons I will not describe the outer packaging which is the one for reviewers.



Ursa Mini Pod Kit; Official Packaging:
The white box shows the image of this item on the front and there is a green "V" in the background.
Writings remind us; the name of the product (Ursa Mini Pod Kit), the name of the brand (Lost Vape), the chipset used (Quest). "Quest" is also represented by a round icon.

There is a lot of information on the back of the box; the packing list, the warnings, some social icons, a serial number, the coloring of this sample (Phantom Green), the scratch & check and various international approvals.

On the edges of the box we find; the main features in the form of icons, and the motto "The Modern Demarcation".





Ursa Mini Pod Kit; Packing List:
• 1 × Ursa Mini Kit
• 1 × Mesh-Coil UB Lite L1 of 0.4Ω Range 20-30W
• 1 × Mesh-Coil UB Lite L6 1.0Ω Range 10-15W
• 1 × Type-C Charging Cable
• 1 × User Manual
• 1 × Warranty Card



Ursa Mini Pod Kit; Accessories:
• 1 × Necklace
• 1 × Suede bag
• 1 × Rubber Bracelet
* Inside to the box (for reviewers) were the items mentioned, I used the bracelet for some images to be included in the review and I'm not sure if I will use the necklace. However, I like the suede bag with laces. Thanks Lost Vape for your thought.



Ursa Mini Pod Kit; Parameters:
• Chipset: Quest
• Body material: Zinc alloy and stainless steel
• Size: 30.7 * 26 * 107.22mm
• Weight: 100g
• Battery: 1200 mAh built-in lithium
• Charging: Fast type C
• Power range: 5-30W adjustable
• Battery voltage: 3.0V-4.2V
• Screen: 0.69 "OLED
• Pod capacity: 3ml
• Refil: From the bottom with silicone plug
• Compatibility: Lost Vape UB Lite Coil Series
• Pod Connection: Magnetic
• AFC: Adjustable



Ursa Mini Pod Kit; Available colors:
• Mist Rose, Crystal Cream, Dark Knight, Glitter Ocean, Phantom Red, Phantom Blue, Phantom Green, Phantom Purple.
* Now I understand what Lost Vape meant by the term "vibrant choices" ... Available colors span different styles. In practice, there are variants for all tastes, some are of sober extraction and others are more or less flashy.



Ursa Mini Pod Kit; Ursa Family:
I received the Phantom Green coloring for this test, I really like the bright green color with a bronze gradient downwards.
As I had anticipated, Ursa Mini maintains the same type of design that we saw previously on the valuable Ursa Multi Kit (I talked about it here): Lost Vape Ursa Quest Kit 100W