The OXVA Vativ super mod breaks the boundaries of mod technologies, The Oxva Vativ Kit included OXVA Vativ mod, Unione PnM Tank & Vativ Pod.

OXVA Vativ mod is the first slide pod mod all over the world, lossless switching between pod mod and 510 mod by the unique slideway design. Vativ mod features Buck-boost chipset with super fast fire (<0.002s) and advanced VPC mode (set the percentage increasement or decreasement of each 0.5s within the first 2.5s).

OXVA Vativ Super Mod is powered by single 18650 battery with real 100W output.

OXVA Unione PnM Tank has 4ml/5ml Pyrex Glass tube for purer flavor and is compatible with Uniplus coils. Unione PnM Tank adopts magnetic connection to change coils in seconds and bottom adjustable airflow system for top flavor.

Features:
Material: Zinc Alloy + PCTG + SS + Glass
Battery: single 18650 battery (not included)
Output: 5~100W
Output Voltage: 0.5~8V
Screen: 0.96 Inch Display
Resistance Range: 0.1ohm~2.5ohm
Charger: Type-C, DC 5V / 2A
Vativ Pod capacity: 4.5ml
Unione PnM tank capacity: 4ml / 5ml
Resistance: 0.15ohm mesh coil (70~80W) / 0.3ohm mesh coil (35~40W)
Lossless switch between pod mod and 510 mod
World first slide pod mod. unique slideway design
Powered by single 18650 battery (not included), real 100W output
Buck-boost chipset, super fast fire (<0.002s)
4 modes: Smart & Power & Volt & VPC, advanced VPC mode
Easy C-frame magnetic battery door
Pyrex N' magnetic
Replace coil / fill in seconds
New Uniplus coils, more clouds and better flavor
Compatible with Uniplus coils

More details for OXVA Vativ 100W Full Mod Kit with Unione PnM Tank, please check >> https://www.3fvape.com/53148-oxva-vativ-100w-full-mod-kit-with-unione-pnm-tank.html

The Timesvape Heavy Hitter Mechanical mod is a made-in-heaven collaboration, designed by Heavy Metal Vapor and TenaciousTXVapes and made by Timesvape, features a gold-plated copper contact and floating battery setting. The Heavy Hitter Mod is a sure win for Mech heads.Three great minds have joined forces to create what could arguably be the toughest affordable mech mod on the market today.

The Heavy Hitter mechanical mod has excellent features including a 28mm body tapered to 26mm at 510 level to accommodate 26mm atomizers, however, a 28mm top section is easily switched by simply unscrewing the underside contacts is a cup and ball type system which reduces the chance of hot buttons caused by arching as the surface area is greatly increased, all contacts are solid copper with gold plating to not only create greater conductivity but low maintenance.

As with all mechanical mods the protections are very minimal, the creators have done what they can to create a safer job with this mod, Delrin lined inserts and a 1/4 turn lock knob come with the risk of short circuit due to un- noticed battery tears (please check all batteries before use) and auto-ignition much less achievable.

Heavy Hitter mechanical tube mod is designed to accommodate 20700 and 21700 batteries (not included), no need to tune for different batteries, battery tuning is self-adjusting to accommodate tolerances in batteries between each brand.

Features:
28mm body tapered to 26mm in diameter
Powered by 1 x 21700 / 20700 (not included)
Internal Delrin battery protection
Floating battery setting and 510 hybrid connection
28mm and 26mm Threaded Top Hat
Full copper gold plated contacts
Removing the Quick Release Battery
Locking the 1/4 turn button
Cup and Ball contact system

More details for this Heavy Hitter, please check >> https://www.3fvape.com/53150-timesvape-heavy-hitter-mechanical-mod.html

I can't decide which one is better. Has anyone tried both of these and which one do you recommend? Thanks a lot.

Vaporesso launched the Vaporesso Target 100 kit & Taget 200 Kit at the same time.There doesn't seem to be much difference between the two from the name, but Vaporesso is certainly not stupid enough to design two identical products. So what exactly is the difference between them, let's take a look.

The Authentic Vaporesso Target 100 Mod Vape Kit near me contains Target 100 VW Vape box mod and TANK Atomizer.The Vaporesso Target 100 Vape box Mod is powered by 1 x 18650 / 21700 battery (not included) and supports wattage adjustable from 5W to 100W.The TANK Atomizer holds 5ml capacity and with 0.2ohm / 0.4ohm mesh coil.

The Authentic Vaporesso Target 200 Mod Kit contains Target 200 VW Vape box mod and TANK Atomizer.The Vaporesso Target 200 Vape box Mod is powered by 2 x 18650 batteries (not included) and supports wattage adjustable from 5W to 220W.The TANK Atomizer holds 8ml capacity and with 0.2ohm / 0.4ohm mesh coil.

Now,do you know which one to choose?Click vape store near me to attend our Halloween Sale.

Quick Link:

Vaporesso TARGET 100 & 200 Kit
Vaporesso TARGET 100 & 200 Box Mod

Have you already got one Freemax Maxus 200W Box Mod Kit? What do you think of this box mod kit? Do you think which features are the main factors to attract you to buy one? As we all know, Freemax Maxus 200W Kit consists of M Pro 2 Sub Ohm Tank and Maxus 200W Battery Mod, and M Pro 2 tank is the brand new updated version of the legend M Pro tank.



Main Features of Freemax M Pro 2 Sub Ohm Tank:
1. There are two editions of M available: Metal Edition & Resin Edition
2. M Pro 2 Resin Editon comes with three steel balls into the top cap to increase friction, while the Metal Edition features the Child Resistant Top Fill Design.
3. The M Pro 2 is equipped with military-grade SS904L mesh and Tea Fiber Cotton formula (95% Tea Fiber Cotton plus 5% Organic Cotton).
4. There are multiple mesh coils compatible: SS904L M Mesh Coils Series, M Pro Mesh Coils Series, and M Pro RBA Coil.

Main Features of Freemax Maxus 200W Battery Mod:
1. Maxus 200W applies patented SmartLoad Tech for loading the batteries without distinguishing positive and negative poles.
2. Maxus 200W supports multiple output modes, including Power, VPC, Bypass, TC-TI, TC-SS, TC-NI, and TCR.
3. Maxus 200W is powered by the dual external 18650 batteries with Type-C and 2A Fast Charging function, which can be fired up to 200W.
4. FM CHIP Maxus 1.0 also provides complete chip protection functions such as short circuit, high temperature, low voltage, timeout protection, etc

Please click here to know more information about Freemax Maxus 200W Kit>> https://www.freemaxvape.com/maxus-200w-kit

So it came up in a conversation I was having the other day, and I'm not entirely sure what they are nor can I find anything online as of late pertaining to this particular law. I know that anyone 18-20 in Oregon can possess/use nicotine products but can't purchase them. But what about someone being of legal age to buy purchasing something for someone who is between the ages of 18-20? Is that illegal or is it not?

You’ve been enjoying puffing on your favorite device then suddenly it is not working anymore. It was procured just a week ago. What could possibly go wrong?


Make cleaning your e-cigarette periodically a habit.

Vaping devices are like any other item you might use in your daily life, eventually and inevitably it will become dirty from dust, pocket lint and other tiny particles.


Check safety precautions such as wattage and battery compatibility, this is not only for the protection of the device but most importantly to avoid accidents for your security.


For pre-built OCC coil and pod cartridge users, always check for e-liquid leakage that can cause flooding on devices which lead to malfunctions.


Caring for e-cigarette devices will make it more durable to use for a longer span of time.


Do you have any additional suggestions? Please feel free to share it with us.


Have a nice day.


-Univapo
For Unique You




In Frame: MISO Pro

All UNIVAPO products are available @ UNIVAPO.com

Hellvape Dead Rabbit 3 RDA is the latest member of Hellvape Dead Rabbit series. Hellvape Dead Rabbit 3 features two different adjustable airflow with honeycomb & slotted airflow to provide different vaping experience. Dead Rabbit 3 RDA has 24mm deck to build dual coils, huge leap to cutting coil legs easily. Dead Rabbit 3 comes with 5mm deep and ample e-juice well without leakage.




Features:
1. Huge leap in coil building and flavor
2. Adjustable airflow with honeycomb & slotted airflow
3. 5mm deep and ample e-juice well without leakage
4. Side feeding design for quick e-juice transferring to cotton by BF pin
...

Click here for more:

Dead Rabbit 3 RDA: Hellvape Dead Rabbit 3 RDA | Healthcabin

The #TARGET80 not only has the original several cool materials, but also adds a new water resistant braid version, which allows you to choose the scene according to your own life tendencies, which one do you prefer?

Feast your eyes on a rare Stabilized Wood YiHi SXmini SL class Mod. This is one of the original batch of "1-Off Custom" Stab Woods sold by Varitube when the SL 1st hit the market. If I'm not mistaken, the Stab Wood SL's aren't even available in the standard "Red-Green-Blue" versions anymore (or VERY rarely if at all) and I know the 1-Offs have been sold out and unavailable for a longgggg time. Matter of fact, don;t think I've ever seen one come up FS on here.... A "Unicorn" one might say truthfully.
This one in the highly detailed and wonderfully grained green custom scheme performs and operates without flaw or glitch (on all its functions & options) and has been relegated to occasional home-only use and normally just a Vape-Stand King for over a couple years now. In great pre-owned condition with just the typical bottom Cap wear marks and very very minor top 510 Cap Atty swirling (can't hardly see without Col. Steve Austin's bionic eye ) Vapes in Power or TC awesomely and the 21700 Batts hold all-day power regardless of your vape Prefs.
Link for Specs & capabilities of the SXmini SL in general:
YiHi SXmini SL Class SX485J 100W Box Mod

Love the SLs (owned 4 at one time) and am keeping my last one (the Copper Gear version) which I'll vape till the "wheels fall off". Truly are great Mods aesthetically, form-factor, ergonomically, and is outstanding in their performance.

Comes as pictured with OEM Box & Books and has the 18650 Adaptor as well. The OEM Charging/Data Cable is AWOL/MIA and not included. But who doesn't already have one, two, too many of these . Batts were NEVER charged inside the Mod.

The standard (non-Stab Wood) SX Sl's normally go for @ $140 On Sale when you can find one. So,,,, I believe $85 plus $12 for USPS Priority Shipping to be not only fair but probably way below current Market Value.

Payment via PayPal ONLY and sell/ship to lower U.S. 48 States (in-CONUS) please. Nothing against my Brothers & Sisters elsewhere just too many hoops & unknowns these days.

Questions welcomed and thanks much for looking & considering

***BONUS BUNDLE OFFER***
Bundle this Amazing Stab Wood Mod with my other Listing's Items (a Brunhilde, a Kylin II, & a Core RTA): For Sale - Brunhilde, Kylin II, & Core RDA Bundle
All for a mere scant $125 plus $12 shipping

Some time ago, on an impulse I bought some tubes of UD wire shots - a tube of wire lengths cut to 6" lengths. This had to be more expensive than a spool, but they were on sale. They've been sitting in my box for a while and today I decided to give them a try.

These are Kanthal A1, 28ga X2 twisted. The coils in a Goon RDA on a single 18650 mech mod were overdue for replacement. I targeted a resistance of 0.55 ohms each, with 3mm dia coils, to end up at about 15 amps. the calculator came up with a 5/4 wrap. So I did. These coils looked tiny on the Goon, but I spread the wraps out to get them to fit on the wide clamp plates. Upon testing, they came out to 0.66 ohms each. This works out to 12.4 amps and 51 Watts. Close enough, plenty of safety factor.

This doesn't produce a cloud machine, but with the air flow turned down about halfway, the hit is slower and longer with good flavor and good satisfaction.

The best part is that I was able to make two coils with a single 6" length of wire!

So this is duly entered into my journal and will serve for future reference.

I have stacked slam piece and it is not fire when I put 2mm spacer with 2 Samsung 30t batteries and also it is not fire when I put the 30t without spacer it is fire only with I joy 20700 5 legs without spacer

Hi all,

I'm looking for a a place to buy more cartomizers from. These are Boge, 510 threaded, 1-2 small hole prepunched, single coil, about 2ohm, about 49mm long, and flanged but the flange has two edges cut off. I don't think Boge makes them anymore but there are some after market ones out there somewhere. Does anyone know where I can get some?

Followup question, why are cartomizers no longer being sold? I like the way the hit better and it seems like my carto tank holds more liquid by mass than the new stuff out there.

"Rather than make cannabis a Main Street fixture, California’s strict regulations have led most industry operators to close shop, flee the state or sell in the state’s illegal market that approaches $8 billion annually, twice the volume of legal sales.

Local government opposition, high taxes and competition from unlicensed businesses are complicating California’s push to build a thriving legal market."

California’s legal weed industry can’t compete with illicit market

Funny How CA Legislators/Regulators Ignore this. But are doing Everything to Ensure the Same Thing happens to the e-Cigarette Nicotine Market.

I have a beta Provari P3 I'm looking to sell. It has a unique diamond design, extremely rare. It is new in the box, but the display is not working. Most of the betas I have seen have had this issue. I have spare displays, if the buyer would like to repair it themselves. asking $160 shipped

Hello everyone. I’m here this time with a review for a company that you may not know much about. To be honest, I really wasn’t very familiar with them until they contacted me and asked me to do a review for them. I’m sure the suspense is killing you by now so I’ll go ahead and tell you that the company I’m speaking of is Univapo. I’ve heard a little talk here and there on the forum about some of their pod devices but not a lot. They are looking to grow and get their name out. I was sent their Miso Pro pod device in order to provide a fair and honest review for you the readers and perhaps help you decide if you’d like to purchase one to try. The Miso Pro is a fairly simple device but has a couple of nice features that I’ll discuss later in this review.






WHAT’S IN THE BOX?

*1xMiso Pro pod kit

*1xUNC 0.8 ohm coil

*1xUNC 1.2 ohm coil

*1xUser manual

*1xType-C charging cable






SPECIFICATIONS:




FEATURES:

Portable

Yet robust, the UNIVAPO Miso Pro is designed for optimal portability.

Its 22mm bright fire button and smooth outlook appearance give it an ultra-modern premium look and feel. A powerfully elegant vaping device.

Convenient Side Refilling

Fill From the E-liquid Filling Hole.

Strong Magnetic Connection

Connect battery and pod firmly.

Airflow Adjustable

You can easily adjust airflow by turning the pod in other directions.

UNC Coil Technology

Taking you to flavor journey

Massive 1000mAh Battery

Weather you go out or at work, we need a long-lasting battery. With 1000mAh ultra high capacity battery, you can use Miso Pro all day long without worrying about running out of battery. And once the battery is low, you can power it up with 5V/2A fast charging.






















INITIAL THOUGHTS:

I thought the packaging on the Miso Pro was nice. The front of the box shows a nice color picture of the device inside and there is a tab on one end that makes it easy to slide out the tray that holds the Miso Pro and accessory pack. The envelope containing the user manual was on top and underneath was the device with a pod already installed and a coil pre-installed. There was a sticker with the Univapo logo on the bottom of the coil to keep it from being fired before it is filled.

Included in the kit was the device with the single pod and one coil pre-installed and in the accessory box was a USB-C charging cord and a second coil. The UNC coils included are a .8 mesh and a 1.2 ohm standard coil. I know it’s not common practice but it would be nice if there was a second pod included. I also received an extra package of .8 ohm coils for the review but it’s not included in the kit when you purchase it. You’ll just get the two included coils.





On the front of the Miso Pro is the large fire button and a single indicator light that illuminates when the device is activated. It can be activated by pressing the fire button or can be used as an auto draw device. The indicator light indicates the battery level. The color of the light shows three different battery levels. Green=High, Blue=Medium, and Red=Low. There are not different output levels on this device and it is determined by the coil resistance. As far as I know there are only the two available coils which are .8 and 1.2 ohm resistance. Also on the front near the bottom is the MISO PRO name etched.

There are only two button operations for the Miso Pro. Five presses of the fire button turns it on or off and three presses of the fire button will lock out the fire button so it will only work in auto draw mode.



On the left side of the battery is the USB-C charging port which is rated for 5V/2A which if this holds true then should charge the battery in about 30 minutes or so. Also you can see on the left side since that’s the way I inserted the pod, is the side fill plug which means you can fill the pod without removing the pod which is a very nice feature in my opinion. The fill plug is pulled from the top but does not rotate so you may have to hold it out of the way while filling. It goes back in place very securely without any mess as long as you don’t over fill the pod.





On the side opposite of the fire button side is the Univapo name etched near the bottom and there is no other branding on the unit.



On the right side is a single airflow hole and there is a viewing window with horizontal lines molded into the side of the pod. The pod can be inserted either way so you can have the fill port and viewing window on either side. Rotating the pod does slightly affect the airflow.



The bottom of the Miso Pro has the 1000mah battery rating on it with the words Made in China and the CE electrical insignia. It is rubberized and can be stood up on a table. It’s a fairly small device like most pod devices like this so it can be fairly easily tipped over.



The pod opening on the Miso Pro has two magnets and two gold plated contacts inside as well as the airflow sensor opening in the left corner of my picture. It seems to be a very secure connection and I have had no issue with the pod coming out accidentally. The sensor does sit a little higher than the base of the inside to help protect should a liquid spill happen. There is a notch in one side of the pod and the way it’s supposed to work is that if you put the pod in with that notch closer to the airflow sensor then it’s supposed to be for RDL and if you rotate the pod with the notch further away it’s supposed to be for MTL. I honestly could tell very little difference between inserting the pod either way.



The pod for the Miso Pro is just slightly tinted which makes it fairly easy to see the liquid level while filling.




The coils are threaded on the back end and there is a knurled nut that screws onto them then the entire assembly is threaded into the pod. I’ve seen this type of design before and honestly am not thrilled about it because if you lose that nut then you can’t use the device. The nut has small airflow holes in it to allow the airflow in through the body of the device and then up to the coil.





FINAL THOUGHTS:

The Miso Pro is a very simplistic pod device but sometimes simple is better. Do you really need different power levels, screen display, or ten button combinations? Sometimes you just want a good vape and don’t want to mess with all that stuff. Especially if you just want something to throw in a pocket that just works when you need it to. That’s what the Miso Pro is in my opinion.

The flavor production was very good in my opinion for a small pod device. I used some dinner lady lemon tart in it during testing and thought the flavor came through nicely and it delivers plenty of vapor. I did prefer the .8 ohm pod which is rated 13-18 watts but there is the 1.2 ohm pod for those that like a lower output coil at 9-12 watts.

I do wish that the Miso Pro had a real airflow control like some other pod devices I’ve tested before. This being said, I do tend to like an airy MTL and the Miso Pro does have that. I can get an RDL from it with the .8 pod but it’s a bit tight. In my opinion it is just better as a loose MTL device with either coil. I can tell a very small difference depending on which way I insert the pod but never got that tight MTL like some people might look for.

So, would I recommend it for you? If you’re looking for what seems to be a well-built small pod device for out and about that delivers very good flavor with a loose MTL then yes I would. I’d like to thank Univapo for sending the Miso Pro Pod kit for this review and a great big thank you to the readers. Below is a link to the Univapo website if you would like to see the entire line of Univapo products.

Miso Pro Kit – Univapo

The subject of today’s review is the Aspire Mixx mod which was sent to me by Sourcemore for the purpose of providing this review. I’ve only started to get into SBS (side by side) mods over the last few months and have three or four. The Mixx has quickly become one of my favorites. The shape and hand feel remind me of the Aspire Boxx which I very much like. The Mixx can be used with most tanks up to 24mm in diameter and a height of at least 30mm is desirable so that the drip tip extends past the top of the mod. As far as operations, it only does VV, VW, and Bypass which honestly will be fine for most vapers. I know there are some out there that still use temperature control but it seems to me like that number is dwindling over time. The Mixx is a really nice unit and is CNC machined which takes 30 minutes per unit to make.






WHAT’S IN THE BOX?

1 x MIXX Mod

1 x 18350 Battery Metal Sleeve

2 x Spare Fixing Screw (For 18350 Battery)

1 x User Manual





SPECIFICATIONS:

Battery Single 18350/18650(Not Included)

Output Wattage 1-60W

Resistance Range 0.1-3.5Ω

Output Mode VW, VV and Bypass

Color Tuxedo, Quick Silver, Jet Black, Amethyst, Sapphire, Orchid, Toffee, Clear Frosted, Smoke Frosted, Yellow Frosted



FEATURES:

1. Made of full metal with CNC process
2. Designed by Sunbox, made by Aspire
3. Single 18650/18350 battery with 60W max output
4. 3 output modes available: VW, VV and Bypass

INITIAL THOUGHTS:

The packaging for the Mixx is what I would consider somewhat nice and reminded me of the packaging on the Boxx. The color picture on the front outer sleeve shows the tuxedo version but I received the quicksilver edition. I don’t know if the outer cover shows the same picture no matter what color you order but mine did not match.

The back side of the package shows the contents of the kit and contains a warning and the address for the parent company.

Once the outer sleeve is removed, you see the mod with a black paper around the outer edge that says Designed by Sunbox on the top. Underneath sits the optional tube that allows you to use an 18350 battery and decrease the height of the mod. In order to do this though you must remove the two screws on the top of the battery tube top plate and use the included extra screws for the shorter tube. I haven’t had any 18350 batteries in years so was only able to test the Mixx with a single 18650 battery.

On what I’m going to call the front of the mod in order to describe the aesthetics is the nice sized fire button that sits inside the cut out in the front. The button is a bit clicky with no rattle and has a nice quality feel to it. Below the button is the Aspire name etched into the body vertically. I find it interesting that they decided to put their name here since it will most likely always be covered by the hand when holding the unit. I have found that I like to wrap my hand around from the back side and fire with my middle finger while resting my lower two fingers over the Aspire name.

On the left side are the + and – buttons to adjust wattage or voltage. They do protrude a little but I find them just a little on the small side. The way I like to hold the mod, my hand covers the buttons so I can’t really adjust the settings while holding the mod normally. This isn’t a huge deal but I guess could bother some people. Under the buttons are a couple of grooves cut into the body of the Mixx horizontally. I guess they are just for looks since they really don’t add anything to the hand feel for me. The battery tube also has three horizontal grooves that match the grooves on the base so they must just be for aesthetics.

On the right side of the mod is the MIXX name etched into the body and once again the three horizontal notches in the side of the mod. The notches are on both sides but do not run all the way around.

On the back side of the mod there is no branding and you just see the back of the battery tube. I do kind of wish I had an 18350 battery so I could try the Mixx in the shorter configuration.

Looking at the MIxx from the top side you can see that the inside of the battery tube is marked with a large red + to mark the battery polarity and the battery cap also has a – sign carved into the underside of it.

On the bottom of the Mixx is the star of the show. The display screen on the Mixx seems rather old school to me. It reminds me of displays of days past. It does however show all the important information. The screen displays battery level, coil resistance, output voltage, output amperage, and of course the set wattage in larger font. They also put the Designed By Sunbox information on the bottom. I found the display to be large enough to see easily and the mod fires quickly despite the old school display. I kind of laughed inside when I saw the lock/unlock symbol when you lock the adjustment buttons on the device. It reminded me of an old Atari game.

The screen adjusts in .1 watt increments but if you hold one of the adjustment buttons down then it will fast scroll in 1 watt increments. Also it will round robin if you hit the high or low setting.

The button operation is fairly straight forward and its operation is as follows.

- Press the fire button five times to lock the device

- While locked, hold the fire button down to turn it off

- Once off, press the fire button five times to turn it back on

- Press the fire button three times to go into stealth mode

- Press the + and – buttons to flip the screen

- Press the + and fire button to switch between VW,VV, and Bypass

- Press the – and fire button to lock the adjustment buttons

FINAL THOUGHTS:

The Aspire Mixx is really a very well designed and well- built device in my opinion. It’s fairly lightweight being CNC machined mostly from aluminum. It has a maximum output of 60 watts which may not be enough for some people but I run a lot of tanks in the mid 20’s range so it’s really plenty for most rtas that I use normally.

I felt like the firing response time was very good and I didn’t notice any output drop as the battery level got lower. The Mixx does not have a USB charging port so you have to charge your batteries externally. This could be a pro or a con depending on the person using it. I do kind of wish it had a port but wouldn’t keep me from purchasing it. One thing I don’t really love is the battery cap. It’s very similar to the one on the Boxx and is just a little hard to control when screwing the cap on after changing batteries.

One other thing I noticed was if I hold the mod and put my pinky underneath the mod then it irritates my pinky a little bit on the edges of the bottom plate. I think that could be solved by rounding the edges of the bottom plate a little more. It could just be me or the sample I received as I know a lot of people love this mod and I haven’t heard any complaints on the hand feel of it.

So, would I recommend the Aspire Mixx for others to purchase and enjoy? Yes, no questions asked. I think it’s a really great mod and fairly inexpensive for such a quality built device. I’d like to thank Sourcemore and Joyi for sending the Aspire Mixx for this review and thanks to the readers that always show up to read my reviews. Below is a link to the Sourcemore website if you’d like to take a look. Don’t forget to log into your account for best pricing.


Aspire MIXX Mod VW VV Box Mod 60W single 18650/18350 (sourcemore.com)

Hi everyone, new member from England UK, needing advice, I use T20 coils with a I stick power pack, I was burning coils every couple of days, so I messed about with the settings and now it's worse, but I can't remember what the original settings were, does anyone know what settings I should be using for a T20 coil? It's 13-14w, so I have the I stick on 13.5, but don't have a clue about the other settings.

Hello fellow ECF members.
I'd like to discuss the Aspire Vilter Kit that was sent to me by Aspire for the purpose of providing a fair and honest review.

Most experience vapers (ex-smokers) will probably agree that switching from smoking to vaping was not easy for most of them and it is still very tough for a good part of smokers, especially the older ones.

Even considering the fact that a smoker knows how bad is smoking for his health and wants to quit, when he/she tries to quit cold turkey, more than 90-95% fail to do that as medical researches show. It's not only because of the addiction, for many, the main problem is that the feel/process they are used to is pretty different if we'll compare smoking and vaping. That is also a reason why for example HNB devices are really popular in many countries all around the world because they imitate the smoking process pretty good and it's making the job of switching for the healthier alternative much easier for smokers.

When I first saw the Aspire Vilter ads I immediately thought about these current smokers who don't want to switch to vaping because of the difference in process - they may not like the plastic/metal drip tips or the absence of the cigarette filter feel when you slightly bite on it. If you used to smoke you probably know it's important at least in the beginning of the switching process. People in general are pretty conservative and it's hard to switch for something totally new even when the health issue is on the map.

Btw, when I was switching from smoking to vaping, there was still a 1st gen. of cig-a-likes on the market. They imitate the cig form factor well but it was the only pro I guess because they were so bad in general: a 100-200 mAh battery that wasn't enough to serve you even for the few hours and the charging time was ridiculous btw, the "juice" back then was the worst blend of tobacco flavour you can imagine, vapour amount was very small and so on but even then it was helping us smokers to switch thanks to the form factor and a similar process.

It's great that the vape industry is moving forward and today we have any types of e-juices and something like Aspire Vilter on the market to help smokers switch with ease. Let's check what is all about:

Vilter Kit is the newest vaporizer device in Aspire series. It comes with 450mAh internal battery, and is charged with USB Type-C port. Aspire Vilter allows you to enjoy the feeling of a cigarette filter with an artificial paper filter drip tip. With auto draw mode, you can enjoy the full taste of your favorite flavors. Aspire Vilter Pod Vaporizer uses premium 1.0ohm mesh coil heads in conjunction with the perfect airflow for an intense and rich flavor experience. (c)

Vilter comes in a compact box. It contains the device, Type C charging cable, manual, the pod with a built in coil, a plastic tip and 2 paper cig-a-like drip tips. (Additional paper tips you can buy separately, they are sold in different colours btw, check here if interested).

Both plastic and paper drip tips are pretty comfortable in my opinion but for smokers who are just starting the switching process the paper filter will be a preferable option I believe - it imitates the cig mouthfeel very well. (A slim cig I have to add)


The pod comes with a magnet lock and holds pretty well.
Refilling process is easy - you lift the plastic part on the bottom of the pod and fill it up to 2ml of e-liquid of your choice. Needle head bottles are preferable as the hole is not too big.

5-10 minutes of waiting time after the first refill and we are ready to go (device came pre-charged from the box).

There are no buttons and screens on the device to make it easy to use for ones who are just switching from smoking I guess + it's a big plus for older people who don't want to check the small numbers on the tiny screens etc.

Auto-draw function works well. I was impressed with the amount of vapor considering the small coil used. Taste wise it is also on the good side in my opinion.
Not sure how long will the coil last, was using mine for about a week and it's still good.

Battery holds for around 2.5 days for me and the charging is pretty fast thanks to Type C connection.
Vilter comes in a range of different colours btw. Check here if interested.

My Final Thoughts on Vilter:

I believe Aspire did a really Good Job here
Vilter kit is not the most powerful, beautiful or revolutionary device on the market but I believe it may and Will help a lot of smokers quit and this is one of the most important things - the initial reason the Vapes were created for!
If you have relatives or friends who wants/tried to quit (and failed) I can surely recommend you trying this simple device in order to help them quit.

Keep vaping and Stay Safe guys

Dear valued customer,

Hope you are doing well!

Halloween 2021 is just around the coner! Healthcabin Halloween Sale with 5 vape deals is ready, to celebrate the season in safe, fun, unexpected ways! Come join us and save more on your favorite products!

A. Sign in to Get Member VIP Price

• Old customers – Please sign in to get your member VIP price, which is about 30% cheaper than regular price. Regular price is the price before login.
• New customers – Please create a new account to get the same member VIP price.

Note: For all E-liquid products & DOVPO products, the member VIP price is the same with regular price, but we are offering better discounts, let’s chck them out.

B. Whole Order Extra 15% OFF
We also created an extra 15% OFF discount coupon code, which is available for all items in our store, so you can save more on everything you need! Take the chance!

Details below:

• Coupon: HW2021
• Date: 23rd – 31st OCT, 2021(-0600 GMT)
• $1 Flash Sale products excluded

C. E-liquid 25% OFF or More
We have also created a coupon code which is available for all e-liquids in our store, you will get 25% when you check-out your order, except those products listed in this sales page, whose prices are ultralow already. For more details, plz feel free to click here.

Details below:

• Coupon: ECS
• Date: 15th – 31st Oct, 2021(-0600 GMT)
• Sales Products excluded

D. Giveaway – Free New Vapes
We are now giving away Voopoo brand new Drag Nano 2 Pod Kit with 10 winners in total, ends on 31st. If you don’t want to buy right now, why not try your luck and win free vapes? Click here to join and win!

E. Vape Deal Links
Here are some other useful links where you can find our best deals:

• Weekly Sale – Best price for new hot vapes with 17% OFF Coupon: WSHC
• $1 Flash Sale – Ultimate cheap vapes
• Clearance – Extremely cheap vapes!

Please view the 5 Halloween Vape Deals here.

Say hi to DRAG NANO 2, a new member of drag series. Are you ready to welcome it?


DRAG NANO 2 continues the classic and stylish Drag design,with the materials of zinc alloy, bringing you ultimate metallic hand feeling. We bring 8 colors this time, 3 colors with PC decorative pieces with single grain and single plating ,and the other 5 colors shape the perfect combination of soft leather and hard mental.you can always find your love.


Apart from the gorgeous colors, DRAG NANO 2 adopts the new top-filling and leak-resistant pod system. It only takes one step to fill the e-juice，just remove the clamshell from the top, and then you can fill the E-juice conveniently. With visible cartridge,there is no need to worry about the out of juice and burnt taste. Let you enjoy every vape moment.

Drag 2 Nano is equipped with two pods of 0.8 Ω and 1.2 Ω, which makes flavor in various layers from original taste and nicotine experience. What’s more, Drag Nano 2 gives Plan B for your, which is also compatible with VINCI Pod cartridge.

With 3 color LED light, DRAG NANO 2 show the output power and battery smartly, so you will never miss any information while you are vaping.


How do do you think about it? Comment below.