Aga-t7

[propofokgov]

@hilljack92, are you flooding while filling? I've noticed that when filling the tank you have to hold it sideways otherwise you'll force juice through the wick holes, causing flooding. I'll fill mine sideways, then tilt the whole thing back up with the juice bottle tip still in the fill hole, allowing it to suck air through the wick holes. Haven't flooded once since filling this way.

@VaPreis, 3 or 4 days... about 4 or 5 tanks.

 

[hilljack92]

Thanks for the info propofokgov. I'll give it a try. I'm dieing to test this thing out

 

[ForeverDiving]

thanks for the info bro. i'll be to pick one up tomarrow. that was the only thing I could think of changing, the way I fill it

Jack, 16ga needles are not usually found in general drugstores. I get mine (20 to 14) from a vet pharmacy.

PS, Kidney Puncher has blunt tip needles 20~14ga and Luer lock syringes.

Any tips for a drip tip for the Aga T7? I'd like something that fits and looks the part, polished SS, straight lines with a few grooves.

 

[PaulBHC]

hilljack if you have a Tractor Supply store near you, they have needles and syringes cheap for animal use. Also pg by the gallon.

 

[ForeverDiving]

hilljack if you have a Tractor Supply store near you, they have needles and syringes cheap for animal use. Also pg by the gallon.

KP has them too... Found them while looking for a suitable drip tip that looks good.

 

[hilljack92]

Any tips for a drip tip for the Aga T7? I'd like something that fits and looks the part, polished SS, straight lines with a few grooves.[/QUOTE]

I've seen soon on eBay that would look beastly

 

[hilljack92]

hilljack if you have a Tractor Supply store near you, they have needles and syringes cheap for animal use. Also pg by the gallon.

Headed there after work. Got one right down the road

 

[ForeverDiving]

Links please!

 

[ForeverDiving]

New Aga-T7 build tip: just rebuilt it as per the UD video, crossed coils, twin twisted silica in each one cut at the edge of the base. Juiced and tucked them down; they barely touch the channels. Assembled. No gurgling at all. Then I started gaining on the wicks (I'm a chain vaper) and intentionally flodded them by covering the airholes momentarily with my fingers and pulling; the juice dripped to the lower chamber and started coming out. Then I remember a tip for the Kayfun 31 from another thread: a juice trap. Just a bed of cotton on the lower chamber. Working beautifully!

 

[hilljack92]

So I got me a syringe. Put a 26g .43 ohm build on it. Finally filled the tank(about 3.5 ml) without flooding. Man this thing is great. Thanks for all the help guys

 

[ForeverDiving]

So I got me a syringe. Put a 26g .43 ohm build on it. Finally filled the tank(about 3.5 ml) without flooding. Man this thing is great.

Terrific! I'm traveling and —stupidly– left my syringe home. Getting one is no problem although I don't think I'll be able to find a blunt tipped needle. Anyway, just a few minutes ago I filled my T⁷ using an ordinary needle tipped bottle (the one of my juice was too thick). Forgot to close the air vents... What a horrible mess!!! My biggest gripe was not the cleaning but having lost about half a tank of NET.com Balkan. These juices are made when you order them.

 

[hilljack92]

That sux. What does closing the air holes do?

 

[ForeverDiving]

Vacuum. I need to find a way to assemble the thing so the fill hole faces 12:00 and the air vents 3 & 9. That way I believe the gravity migration to the lower chamber and subsequent spillage can be minimized.

Tapatalk Pro / Samsung Galaxy 4

 

[etchie]

If I were to recommend an rba to a newbie, I'd have then avoid gennys. Drippers or maybe a kayfun would be what I'd recommend.

Yeah, I'm an RDA guy myself.

 

[Aesop]

It is a great atty, aside from the fill problem.

I went with dual vertical coils instead of the crossover horizontal coils.

It vapes as well as most dual coil drippers I have, and no leaks or dry hits while vaping. If only filling it wasn't such a mess. I close the air intake and fill sideways with a syringe...and still get a little leaking.

Many say it's ugly, but the look of it has kinda grown on me

 

[Kemosabe]

It is a great atty, aside from the fill problem.

I went with dual vertical coils instead of the crossover horizontal coils.

It vapes as well as most dual coil drippers I have, and no leaks or dry hits while vaping. If only filling it wasn't such a mess. I close the air intake and fill sideways with a syringe...and still get a little leaking.

Many say it's ugly, but the look of it has kinda grown on me

Looks great with that pharoah drip tip. That mod ain't too shabby lookin either. Which mod is that?

 

[JustB'nMe]

I'm interested in this topper but it looks pretty big. So, I'm wondering, since it says it can be used as a dripper has anyone tried it? If so, what does it look like in that form and how do you like it?

Live well, Love hard, Laugh often & Vape on!

 

[Aesop]

@Kemosabe, it's the Copper Black Stingray (Clone) from FastTech with a GunMetal Nemi (also clone) switch. I do like that DT better than the one that came with the mod.

Here's a better pic:

@mzvgonly, I'm not sure how it would work as a dripper, since the top cap and firing chamber are both female threaded. I did vape directly off the chimney with the tank removed while I was trying to finish off the juice on the cotton in the firing chamber. I'm cheap like that

 

[Kemosabe]

@Kemosabe, it's the Copper Black Stingray (Clone) from FastTech with a GunMetal Nemi (also clone) switch. I do like that DT better than the one that came with the mod.

Here's a better pic:

@mzvgonly, I'm not sure how it would work as a dripper, since the top cap and firing chamber are both female threaded. I did vape directly off the chimney with the tank removed while I was trying to finish off the juice on the cotton in the firing chamber. I'm cheap like that

That is great to know that the stingray and nemmy switches are interchangeable. Looks great.
So do you have a nemmy hybrid adapter on that mod too, or does it just appear so?

 

[Aesop]

No hybrid adapter, the SS ring on the very bottom is the Stingray top cap.

The Nemi has odd threading 20.5 x 0.5 mm (top) and 18.5 x 0.5 (bottom). The Stingray has 20 x 0.5 mm (top) and 19 x 0.5 mm (bottom). It's close enough that the switch is usually interchangeable (on the clones at least), but not the top or extension tubes.

On the plus side, you can hybrid the Aqua on the Stingray and for pure silliness use the Origin top cap or extension tubes.