I have a few problems with some Dvarw clones I received and wanted to consult with another experienced vaper. Please PM me, and we can organize.
I live thousands of miles away, but I've been using Dvarw atomizers since 2019. I'm not sure what issues you're encountering, but generally, they require only a few adjustments. The design between the MTL and DL models doesn't vary much: for both, what's crucial is to completely cover the cotton wicking slots, otherwise, it will flood.
Remember to properly lubricate the O-rings of the movable chamber and always make sure to insert the final cap. If you're using second-hand Dvarw atomizers, I'd recommend replacing all the O-rings. If they don't seal properly, you'll run into flooding and the draw won't be silent.
Remember to properly lubricate the O-rings of the movable chamber and always make sure to insert the final cap. If you're using second-hand Dvarw atomizers, I'd recommend replacing all the O-rings. If they don't seal properly, you'll run into flooding and the draw won't be silent.
I have 3 clones here. No coil is placed inside. I place eliquid in the container (upside down), and tighten the Dvarw shut. I place it upright, and in a few minutes it will leak from the bottom rectangle.
I will take pics later. The top portion that attaches to the glass, does that have an oring? Mine do not.
I will take pics later. The top portion that attaches to the glass, does that have an oring? Mine do not.
The times i did place a coil inside with cotton, and then vaped, the tank spat up liquid immediately, then started leaking down the bottom.
The plastic tank is held by an o-ring at the top and bottom, so two o-rings. If one is missing, it will leak. This is the modder's website KHW mods with several photos to help you figure out if you're missing any o-rings
I don't know which Dvarw you have, this is the FL (Peek chimney, steel chimney cap) DL version released in 2020, but the same applies to both the first one and the CL released in 2023:
The arrow points to the chimney cap: if you forget this] or don't close it properly, it will 100% leak.
In the red circle, you can see the hole from which, when you wick [your coil], it must be COMPLETELY filled with cotton, or here too, if it's not well covered, it will leak.
There are many ways to wick the Dvarw, from passing the cotton through the coil and then feeding the wicks/tails into the chimney the Peek part in the pic), or wicking the coil, folding the wicks/tails into the deck, and only then inserting the chimney. The important thing is that when you arrange the cotton and look at the hole I circled, you see it totally covered with cotton.
A video in Italian, which you can very well mute, where from minute 3:50 you can see the simplest and fastest way to arrange the cotton on a Dvarw.
WOW. I am doing it all wrong ...I am nowhere near putting enough cotton in. Also I had no idea the exterior holes had to face the cotton. By the way, I live in Florida for 40 years, but I am Roman "So de Roma!", so i understood the video. Let me try to rewick and I will let you know
IT WORKS!!!! mannagia la miseria. I was using hardly any cotton, and not blocking the holes.
Thank you so much!!!
Thank you so much!!!
I live about 30 km from Rome; I never would've thought I'd find a fellow countryman on an American vaping site.
I'm glad you managed to get it working; the Dvarw is considered a great atomizer here.
Ammazza-o, troppo forte!
Thank you so much. I lived for many years on the Via Appia Pignatelli, on the corner of the Via Appia Antica, when I was a child, but then my parents moved around. I still speak "Romanaccio", but here in Florida very few speak it.
The Dvarw is fantastic, it's very similar to the Kayfun GTR clone. I also have a Brunhilde MTL, Bishop V2, Ares 2. They are all great. Ancore grazie e a presto!
Thank you so much. I lived for many years on the Via Appia Pignatelli, on the corner of the Via Appia Antica, when I was a child, but then my parents moved around. I still speak "Romanaccio", but here in Florida very few speak it.
The Dvarw is fantastic, it's very similar to the Kayfun GTR clone. I also have a Brunhilde MTL, Bishop V2, Ares 2. They are all great. Ancore grazie e a presto!
My family (I Papa) all live in Rome. Apparently it's difficult to find e-liquid in italy?
No, everything can still be found, but the problem lies with the various legislations and bans. They've gone as far as taxing flavorings (those to be diluted at 10%) at €1.10 per 10 ml, making it illegal to purchase them from shops without a tax warehouse or from abroad. They've also banned the online sale of nicotine from January 1, 2025, even when buying from Italian shops. This means that for 10 ml of nicotine at a maximum of 20 mg, each shopkeeper can charge anywhere from €4 to €10. The disposables you have in America were almost immediately blocked here; the maximum allowed are 2 ml disposables with a maximum of 20 mg of nicotine. So, the more time passes, the more expensive it gets, By organizing a bit, it still costs less than smoking, even when using nicotine.
make sure to proudly carry romanaccio into the world and introduce it to as many Americans as possible
If you have any other questions about other RTAs, feel free to tag me
What a nightmare with nicotine. Here in Florida I mix my own liquids. I buy gallons of VG and PG, and let different teas seep in the liquids, then after a few weeks, add flavors (Mint, lime, ginger etc). The nicotine is added last. Here we can find 100% nicotine but it is expensive. Many e-cig stores have closed, and it's becoming harder and harder to find good tobacco flavors. I have been vaping since 2007, and back in the day we used to order Dekang liquids directly from china, but all that has gone now. Here 500 ml of liquid nicotine costs about $70. There are two good chinese sites that sell equipment (3FVAPE, and sourcemore. I am sure you use those too.
Similar threads
- Locked
