Can someone who has both the Cthulhu v2 and Aromamizer chime in on flavor? I like the restrictive lung hits that are very heavy on flavor -- clouds are inconsequential. Trying to decide whether to jump in on the Smog deal, or just wait until the inevitable v2 is released (and sidesteps the need for those bands).
Aromamizer RDTA by Steam Crave
- Thread starter roxynoodle
- Start date
- th_trl_thread_readers 0
- Status
I just enough flavor out of the Aromamizer. Maybe it's because I have been using the Velocity exclusively for the past month or so. I have been using dual claptons on them both. It's probably something I'm not doing right on the Aromamizer. Still a good tank though.
Sent from my VS986 using Tapatalk
Sent from my VS986 using Tapatalk
It's here! 3ml with velocity deck. And pre-ordered Radius....best Tuesday ever! Can't wait to go home and build it....
Mine is NOT here waaaaaaaaah. Still marked as scheduled for delivery today, but no sign in tracking that it's escaped what is apparently the postal Bermuda triangle on Long Island.
WHYYYYYYYYYYYYYYYYY.
On the plus side my Angelecigs package got here, hilariously packaged. Like every little thing was in its own padded envelope inside another padded envelope inside a bigger padded envelope....just spring for a single box guys and save yourselves the trouble lmao.
But the Goblin Mini oh my god it's so sexy. So tiny and solid feeling. Can't wait to try it.
But not as much as I can't wait to try my Aromamizer
WHYYYYYYYYYYYYYYYYY.
On the plus side my Angelecigs package got here, hilariously packaged. Like every little thing was in its own padded envelope inside another padded envelope inside a bigger padded envelope....just spring for a single box guys and save yourselves the trouble lmao.
But the Goblin Mini oh my god it's so sexy. So tiny and solid feeling. Can't wait to try it.
But not as much as I can't wait to try my Aromamizer
Last edited:
So, I'm torn on how to build this thing. ATM, I'm using Ti and I have never built a dual coil with it. I don't want to pulse it before hand, could that be a problem with duals? If I build it as a single, is there something special I need to do with the wicking and airflow?
If you want to do a single, some have blocked the juice holes on one side with toothpicks or something. But I agree, just use spaced coils.
HHmm...maybe it was a mistake rolling 3mm ID coils (9 wraps)....I'm afraid to put the chamber on, it looks like it might cause a short.
It seems to have a bit of a learning curve...I just had about a ml of scalding hot liquid leak out of an air-hole as I vaped. I thought I stuffed it with cotton...
My build came out to 0.21 Ohms (26G Ti, 9 wraps, 3mm ID).
My build came out to 0.21 Ohms (26G Ti, 9 wraps, 3mm ID).
I'm finding it difficult to dial in a good vape. I'm getting very little vapor with no taste except 'hotness'. So far, I have tried it between 40-80J, and I lowered my temp to 350F ( I usually keep it between 400-420 in my other tanks). I'm not used to vaping at this range (and not used to dual-coils). I have gone as low as 0.3 on my Lemos and Crown, and they were awesome vapes, even though I normally prefer a bit higher resistance. I want to love this tank (love the form factor and ease of building), and I respect the opinions of people in this thread, so I will keep at it. Any advice would be greatly appreciated.
Zombo, I can't imagine why it would be hot with the airflow this thing has.
Could you have a hot leg?
What deck did you use?
What mod are you using? In ti mode or ni200 mode or using manual tcr?
Could you have a hot leg?
What deck did you use?
What mod are you using? In ti mode or ni200 mode or using manual tcr?
Have you blocked the two extra holes? Just keep open the holes that are closest to your coils. If I vape with all holes open, I get no flavor and just hot vapor as the air is not going in to cooling coils.
I am really disapointed in the 2-post decks.
First 2 decks had the screw holes drilled trough so my leads were cut very easily when tightening the screws enough to not get any fluctuating resistance.
I got replacement decks with the screw holes not drilled through but they were still too deep and cut my leads.
I filled them with silver wire and leads don´t get cut anymore but the wall is so thin that it has bulged from other side. I hope it wont break.
Screws are also really bad quality, I´ve have used almost all of the spares that came in the package. The heads just give up.
I really like the vape but the 2-post deck is not very well made.
They could have make the posts a bit bigger and maybe with m3 screws.
Also I don´t see the point of having 4 airholes but not a big deal as they are easy to block.
This is not the perfect atty for me but really close.
It wasn't tasting burnt like a hot leg.
Using the velocity deck.
It's on my IPV4S in Ti mode.
I now have it at 90J and 400F, and it's starting to perform well, but it's still a bit hot with muted flavor. I think maybe I just prefer a higher resistance and more mouth-to-lung. I have been using the black band (not crazy about the yellow one they sent me...the black at least matches my IPV). However, I keep the holes only partially open. Maybe that's affecting the performance. I will try to yellow band next.
I will have to find a lighter gauge Ti or maybe even go back to Kanthal so I can get a higher resistance. Or...maybe try a single coil.
The leaking seems to have stopped. Also, I managed to squeeze in my 3mm coils without shorting.
Using the velocity deck.
It's on my IPV4S in Ti mode.
I now have it at 90J and 400F, and it's starting to perform well, but it's still a bit hot with muted flavor. I think maybe I just prefer a higher resistance and more mouth-to-lung. I have been using the black band (not crazy about the yellow one they sent me...the black at least matches my IPV). However, I keep the holes only partially open. Maybe that's affecting the performance. I will try to yellow band next.
I will have to find a lighter gauge Ti or maybe even go back to Kanthal so I can get a higher resistance. Or...maybe try a single coil.
The leaking seems to have stopped. Also, I managed to squeeze in my 3mm coils without shorting.
I have been keeping them partially open (black band)....maybe that's my mistake.
Is the black band the 4 hole? How are your airholes lining up? You could try unscrewing the base 1/8 of a turn to let air from all 4 holes cross the deck at diagonals.
Anyone drill out the juice holes at the bottom of the deck? seriously thinking it over.
Yes, the 4 holed one. I got a feeling the 0.2 is just too low for me. It reminds me of the 0.25 non-TC coil they included with my Crown...it opened up at 80W but was way too hot (and airy) for me.
Honestly can't tell how my airholes are lining up...my eyesight isn't what it used to be...even with reading glasses.
tip from a derringer is perfect imo.
think i will get another tank with the v deck and a spare tri deck and experiment on the tri deck i have now. im a little bummed at how large the post holes are on vaping bogans deck, mine are tiny, no way i can get dual 22ga in there.
- Status
