Aromamizer RDTA by Steam Crave
- Thread starter roxynoodle
- Start date
- th_trl_thread_readers 0
- Status
Beautiful work. Thanks. What's the spec. on the LIPO?
Do you post your work elsewhere on this site?
You can get a better look inside here: https://drive.google.com/open?id=0ByJGOatX48BAU0RYcUNQM2l4MkU
Its a work in progress and not quite complete yet.
The battery is a Turnigy Nanotech 1300mAh, 25C, 3S and the Escribe Battery analyzer clocked it in at 14.83 Watt Hours.
Other Battery Results can be viewed here: https://goo.gl/b33IPB Select the Battery tab at the bottom. It is new so there arent a lot of entries yet.https://goo.gl/b33IPB
You can see some of my other stuff here:
https://www.e-cigarette-forum.com/forum/threads/mike-n-tibs-dna-mods.542055/
And frequently in the Co-op section.
How are you building single coils on this tank? I'm curious. The ones I built weren't worth a darn, so I went back to duals.
I put 26-32 claptons with 6 wraps in this thing and she is purring at 60 watts. 6 wraps each, 2mm ID, kanthal. This tank was wigging out on my x cube whenever i loosened the build deck from the base even slightly so i am liking it better in watts mode. It was fine on my evic vt but ohms jumped all over on the x cube.
hi mark !
I have 3 of them going different sizes , different gages , horizontal and vertical . so trying different builds .
the last one I used twisted 30 gage on 3 mm form on the v deck and upped the wattage to 23 .
the important thing is the placement of the coil usuely raised up a bit to center the coil and then sideways by backing up about one eights.
so you want the air centered on the coil.
but don't forget ...what I like might be totally different than yours.
I have 3 of them going different sizes , different gages , horizontal and vertical . so trying different builds .
the last one I used twisted 30 gage on 3 mm form on the v deck and upped the wattage to 23 .
the important thing is the placement of the coil usuely raised up a bit to center the coil and then sideways by backing up about one eights.
so you want the air centered on the coil.
but don't forget ...what I like might be totally different than yours.
Rolf, I made a bit of smaller Clapton wire tonight. Apparently I should use my reading glasses more often though. I thought I made 28/34, but its 28/32, lol! I'll try it of course and let you know how that goes.
thanks roxynoodle looking forward for finding out how they work.
I did order some 34 g 100 feet so if you don't have 34 let me know .
I did order some 34 g 100 feet so if you don't have 34 let me know .
I definitely think this is worth a shot. Thank you for the tip.
Sent from my VS986 using Tapatalk
Hey gang, anyone of you guys tried using the OCC Ni200 - 0.15ohm single coil head in TC mode? Feed back interested. TY
011364
Dammm! this thing is good!
i normally vape on a mech around 0.08-0.15 around the 95w-180w range depending on atty used.
my build etc:
Dual 24g A1Kanthal
5wraps
2.5mm id
0.2ohms
horizontal coils on the velocity deck
6ml tank
2 indirect holes blocked
using the driptip that came with it
60watts on the sigelei is plenty
i went with the high coils
i went with the coils slightly higher rather than face on with the airholes
the rubber seals have a little give in them so its real easy to get the coils lined up with the airholes, it doesnt get any easier than this.
i give it 10/10 for everything
Dammm! this thing is good!
i normally vape on a mech around 0.08-0.15 around the 95w-180w range depending on atty used.
my build etc:
Dual 24g A1Kanthal
5wraps
2.5mm id
0.2ohms
horizontal coils on the velocity deck
6ml tank
2 indirect holes blocked
using the driptip that came with it
60watts on the sigelei is plenty
i went with the high coils
i went with the coils slightly higher rather than face on with the airholes
the rubber seals have a little give in them so its real easy to get the coils lined up with the airholes, it doesnt get any easier than this.
i give it 10/10 for everything
011364
Dammm! this thing is good!
i normally vape on a mech around 0.08-0.15 around the 95w-180w range depending on atty used.
my build etc:
Dual 24g A1Kanthal
5wraps
2.5mm id
0.2ohms
horizontal coils on the velocity deck
6ml tank
2 indirect holes blocked
using the driptip that came with it
60watts on the sigelei is plenty
i went with the high coils
i went with the coils slightly higher rather than face on with the airholes
the rubber seals have a little give in them so its real easy to get the coils lined up with the airholes, it doesnt get any easier than this.
i give it 10/10 for everything
Have you tried doing vertical coils like this?
Thats what my plan was for when it arrived But i was a bit pushed for time so whipped them in as is
have you tried both ways?i have lots of juice already made for my rda's at between 3-6mg i've had to vape half a tank off and add neat vg as the flavour is to strong and the nic made me feel sick as hell earlier lol not good! .... good for the pocket
What is "Fiber Freak Core"?
Vertical twisted nickel with kgd cotton and fiber freak core. Damn this is insane.
- Status
