Atmistique Atomizers

[mrpumuki]

^ I can only agree with that!

 

[tmcase]

The ohm output has nothing to do with the NR. It's all up to the amount of R you're using e.g. 4.4cm of .20mm A1 kanthal will come out at approximately 2 ohm regardless of how many wraps you make. Hope this helps

What I meant was I didn't wrap all the R wire around the wick so I would have enough leg to stuff in the ceramic post hole where the pin goes. My nr-r-nr wire was 2.2 ohms. It came out 2.2 ohms even after cutting off the one NR wire and using fewer wraps. Had I left the NR wire on, then I could have had more wraps and still had a long enough leg to stuff in the ceramic post hole. Might even get more vapor but it's putting out quite a bit now.

Man this thing is noisy?

 

[tmcase]

tmcase: as mrpumuki correct note you definitely need both edge of nr wire for the reasons he explained. Also the second o-ring is for better sealing

Hope you enjoy your new Diver

Thank Kon. Next build will be nr-r-nr.

 

[tmcase]

Should work with one o-ring, but you know whom to PM if you want more... I don't have the blue ones, though, so you will be stuck in Uncool Cat Territory with me if you get my pedestrian black o-rings.

I think you might have already sent me a few for my Diver V1. I'll have to check but thanks for the offer. I'll let you know. So far I'm not seeing even a drop of juice on my connector pin.

 

[tmcase]

The NR leads on any ready wire will definitely be too long, and they will need to be trimmed down. The ready wires I have probably lose about 80% of their length when trimmed down. Are the NR leads too wide gauge to go through the holes? I have a LOT of ready wires I will never use, I can send you a pack so you can compare, if you tell me which resistance you prefer.

My ready wires go through the holes just fine but I would never turn down some free ones if they aren't being used. Anything over 2 ohms.

 

[tmcase]

I think you are the nicest person on the whole internet.

Ditto that.

 

[Konstantinos]

One of the reasons i always love forums...volunteering

 

[Wmmeese]

Konstantinos, got the BilletBridge and it works great. What is the chance you will make a version comparable with the Nautius Heads as they are way better than the rgular Aspire BDC heads.

 

[Konstantinos]

I wish we could but they are too long to fit.

 

[mrpumuki]

Little pic of my beautiful sets.

 

[Konstantinos]

You must have a big tank collection

 

[Kataphraktos]

Little pic of my beautiful sets.

You are ahead of me by one - unless you count my v2 Grail.

 

[Konstantinos]

If we think Grail like a spare diver tube

 

[mrpumuki]

You must have a big tank collection

Not even. Just two BilletBox tank and two Bayou. Want to find a tripolis from kir franis but they have been out of stock for a long time now.

 

[qorax]

What is Eviva?

 

[StrikeIII]

What is Eviva?

Yes, Please share.

 

[Kataphraktos]

There's a couple of pics up on the Atmistique site, and some more on FB. I'll leave it to K to make the Grand Reveal.

 

[qorax]

There's a couple of pics up on the Atmistique site, and some more on FB. I'll leave it to K to make the Grand Reveal.

Oh! Hitting the Atmistique page then

 

[qorax]

Nope, didn't understand a thing except that there are two Evivas ~ Eviva-T and Eviva-D. Obviously one is for Dripping and the other is a Tank system. But that's about it.

Calling Konstantinos pls!

 

[Konstantinos]

In Greece, during our celebrations and feasts, when we clink our glasses, we say “ygeia” (“health”) or “eviva” which is the modern version of the ancient Bacchus-Dionysian exclamation “ευοί-ευάν” (evi-evan!). So we named our new repairable atomizer “Eviva”, because we want every draw to feel like a party!

Its main body is made from AISI 304L food grade stainless steel, while the pole is adjustable and brass for better conductivity. The insulated part of the base is made of Ketron® food grade peek, a material that can withstand extremely high temperatures (249 °C continuous – 310°C over short periods of time).

The main part of the atomizer hosts a classic CE2 ceramic cup to ensure its unique superior taste, within which you can set up the coil using ONLY resistance wire, making replacement much more practical and easy. This ceramic cup may also be replaced by an SS replacement, for those who enjoy a cooler vape.

We have retained the same liquid feeding methodology as in Diver; however here we have the advantage of a larger diameter, which provides a larger liquid chamber and enhanced feeding.

The air inlet is adjustable with three holes at clock positions twelve, three and six, allowing you to select the desired draw precisely and it lines up perpendicularly with the coil and then straight to the drip-tip. At the end the precise design of the top cap and the bell minimizes leaks during the process of filling liquid.

With a diameter of 23mm the tank version has a height of 36.5 mm and a capacity of 3ml. Besides of the outer part and the final upper cap, it also includes a bell type 3mm conical tube reaching to the drip-tip for a thicker vape with a smooth-strong throat hit. The dripping version has a height of 28mm and capacity of ~1ml. The two versions share the same base system.

In the package you will find a ready coil, an Allen key and a complete set of spare o-rings.

They will be available also:
Air control ring especially design for Provari
24k Golden plated air control ring
Two new Eviva drip-tips
Κit to transform tank to dripping version and vice versa
A little bit later a clear tube

So… Eviva!