Atmistique Atomizers
- Thread starter billakosgr
- Start date
- th_trl_thread_readers 0
- Status
What I meant was I didn't wrap all the R wire around the wick so I would have enough leg to stuff in the ceramic post hole where the pin goes. My nr-r-nr wire was 2.2 ohms. It came out 2.2 ohms even after cutting off the one NR wire and using fewer wraps. Had I left the NR wire on, then I could have had more wraps and still had a long enough leg to stuff in the ceramic post hole. Might even get more vapor but it's putting out quite a bit now.
Man this thing is noisy?
tmcase: as mrpumuki correct note you definitely need both edge of nr wire for the reasons he explained. Also the second o-ring is for better sealing
Hope you enjoy your new Diver
Thank Kon. Next build will be nr-r-nr.
I think you might have already sent me a few for my Diver V1. I'll have to check but thanks for the offer. I'll let you know. So far I'm not seeing even a drop of juice on my connector pin.
My ready wires go through the holes just fine but I would never turn down some free ones if they aren't being used.
Anything over 2 ohms.
Konstantinos, got the BilletBridge and it works great. What is the chance you will make a version comparable with the Nautius Heads as they are way better than the rgular Aspire BDC heads.
Little pic of my beautiful sets.
You are ahead of me by one - unless you count my v2 Grail.
Not even. Just two BilletBox tank and two Bayou. Want to find a tripolis from kir franis but they have been out of stock for a long time now.
There's a couple of pics up on the Atmistique site, and some more on FB. I'll leave it to K to make the Grand Reveal.
Nope, didn't understand a thing except that there are two Evivas ~ Eviva-T and Eviva-D. Obviously one is for Dripping and the other is a Tank system. But that's about it.
Calling Konstantinos pls!
except that there are two Evivas ~ Eviva-T and Eviva-D. Obviously one is for Dripping and the other is a Tank system. But that's about it.Calling Konstantinos pls!
In Greece, during our celebrations and feasts, when we clink our glasses, we say “ygeia” (“health”) or “eviva” which is the modern version of the ancient Bacchus-Dionysian exclamation “ευοί-ευάν” (evi-evan!). So we named our new repairable atomizer “Eviva”, because we want every draw to feel like a party!
Its main body is made from AISI 304L food grade stainless steel, while the pole is adjustable and brass for better conductivity. The insulated part of the base is made of Ketron® food grade peek, a material that can withstand extremely high temperatures (249 °C continuous – 310°C over short periods of time).
The main part of the atomizer hosts a classic CE2 ceramic cup to ensure its unique superior taste, within which you can set up the coil using ONLY resistance wire, making replacement much more practical and easy. This ceramic cup may also be replaced by an SS replacement, for those who enjoy a cooler vape.
We have retained the same liquid feeding methodology as in Diver; however here we have the advantage of a larger diameter, which provides a larger liquid chamber and enhanced feeding.
The air inlet is adjustable with three holes at clock positions twelve, three and six, allowing you to select the desired draw precisely and it lines up perpendicularly with the coil and then straight to the drip-tip. At the end the precise design of the top cap and the bell minimizes leaks during the process of filling liquid.
With a diameter of 23mm the tank version has a height of 36.5 mm and a capacity of 3ml. Besides of the outer part and the final upper cap, it also includes a bell type 3mm conical tube reaching to the drip-tip for a thicker vape with a smooth-strong throat hit. The dripping version has a height of 28mm and capacity of ~1ml. The two versions share the same base system.
In the package you will find a ready coil, an Allen key and a complete set of spare o-rings.
They will be available also:
Air control ring especially design for Provari
24k Golden plated air control ring
Two new Eviva drip-tips
Κit to transform tank to dripping version and vice versa
A little bit later a clear tube
So… Eviva!
Its main body is made from AISI 304L food grade stainless steel, while the pole is adjustable and brass for better conductivity. The insulated part of the base is made of Ketron® food grade peek, a material that can withstand extremely high temperatures (249 °C continuous – 310°C over short periods of time).
The main part of the atomizer hosts a classic CE2 ceramic cup to ensure its unique superior taste, within which you can set up the coil using ONLY resistance wire, making replacement much more practical and easy. This ceramic cup may also be replaced by an SS replacement, for those who enjoy a cooler vape.
We have retained the same liquid feeding methodology as in Diver; however here we have the advantage of a larger diameter, which provides a larger liquid chamber and enhanced feeding.
The air inlet is adjustable with three holes at clock positions twelve, three and six, allowing you to select the desired draw precisely and it lines up perpendicularly with the coil and then straight to the drip-tip. At the end the precise design of the top cap and the bell minimizes leaks during the process of filling liquid.
With a diameter of 23mm the tank version has a height of 36.5 mm and a capacity of 3ml. Besides of the outer part and the final upper cap, it also includes a bell type 3mm conical tube reaching to the drip-tip for a thicker vape with a smooth-strong throat hit. The dripping version has a height of 28mm and capacity of ~1ml. The two versions share the same base system.
In the package you will find a ready coil, an Allen key and a complete set of spare o-rings.
They will be available also:
Air control ring especially design for Provari
24k Golden plated air control ring
Two new Eviva drip-tips
Κit to transform tank to dripping version and vice versa
A little bit later a clear tube
So… Eviva!
- Status
Similar threads
- Locked
