The last week of June Eviva atomizer will be available again together with the clear tube and the AFC 23 to 22mm
Atmistique Atomizers
- Thread starter billakosgr
- Start date
- th_trl_thread_readers 0
- Status
Hi All, I have a couple of diver questions.
How far down into the ceramic cup should the coil/wick be for optimal function. I use cotton and it tends to sink down below the notches as I make the connections. Also,should it be turned in a Billet Box tank any particular way for optimal function?
How far down into the ceramic cup should the coil/wick be for optimal function. I use cotton and it tends to sink down below the notches as I make the connections. Also,should it be turned in a Billet Box tank any particular way for optimal function?
There isn't a special position. Just remember the coil must leave enough space for air to pass (otherwise if the air cant pass free you may have leakage).
The higher you put your coil in the ceramic, you will have more air draw and also a little bit cooler result.
About the BB my only suggestion is to avoid screw the BB ring too tight.
Also as Kat wrote: "with the BB tank, if you have a tiny hex set, tighten down all the screws holding the clear front plate to the white plastic body. Also, after you fill through the rubber ball, press down on the clear faceplate with your thumb a few times, to make sure that rubber ball pops back in to place and seals the tank"
The higher you put your coil in the ceramic, you will have more air draw and also a little bit cooler result.
About the BB my only suggestion is to avoid screw the BB ring too tight.
Also as Kat wrote: "with the BB tank, if you have a tiny hex set, tighten down all the screws holding the clear front plate to the white plastic body. Also, after you fill through the rubber ball, press down on the clear faceplate with your thumb a few times, to make sure that rubber ball pops back in to place and seals the tank"
As petemoss mentioned in the BB thread as well - I put quite a bit of cotton in mine, but I make sure the cotton is flattened out where it meets the slots, so it isn't completely blocking them up.
I have run it with coil all the way inside the cup and sitting 100% on top of the cup with no problems. Make sure the cotton isn't getting jammed into the cup notches, too, as it could get choked off and not wick. I tend to build the coil above the cup in all my Divers, just so the cotton is completely unimpeded by the slots in the cup.
Had this in regular rotation since review and still amazed how well it wicks with that litle hole 
Had this in regular rotation since review and still amazed how well it wicks with that litle hole
Wick it with Cellucotton. I chain vaped it for like 2 minutes (zero nic juice) and every hit was awesome.
And I'm going to say this, and I don't care who gets ticked off: Eviva is more leakproof than my Spheroids.
For those of you who use the use plain 30 gauge resistance wire for your micro coils in the diver,
how many wraps are you using?
how many wraps are you using?
For the BB, I try to hit 2.3 ohms or so, I believe that is 8 or 9. But I use R/NR - I assume by plain, you mean R-only?
Hello there
Inner 9*1.5mm out 10*1mm
If you need them please put a note in your next order and I will take care
Inner 9*1.5mm out 10*1mm
If you need them please put a note in your next order and I will take care
Thank you!!!
I dont need them now, but you know, I feel better with spare parts
I dont need them now, but you know, I feel better with spare parts
Hello Konstantinos, I didn't knew you had your own topic, so I will post the problems I have with the Diver V2 also here below, maybe you know a solution for this problems, but to be honest, I'am done with the Diver V2 as it seems to be a useless device.
Earlier posted:
I can go along with Tbev, atomizers of KF or TF and devices like that don't fail, there performances are great, anyway this topic is about the Rebuildable carto's for tanks and I took a Diver V2 for my just ordered Phini and arrives hopefully soon but I wanted the best Atomizer for my Phini because I think Phini deserves it.
Just trying the Diver V2 for 2 days now and can't say I'am positive about it, the leaking problems of the center pin Atmistique fixed with the 2 O-rings, a poor solution but it works, but now its leaking from the little hole into the center pin and a lot.
I have been informed by advanced that the Diver is very sensitive when it comes to pressure build-up and pressure differences, in short the Diver often if not all the time gives problems with, I think you can imagine that I wasn't happy to hear this at all *sad face*
The problem of leaking all your liquid out of tank when installing the Diver into it, this can be solved by hold the Diver between 2 fingers by the top of the Diver and to the center pin following by pressing really hard at both sides and you ready to bring your cap closer to the tank and place it.
I will not give it up that quickly, so i will make a new setup for this device and hopefully i will find a solution for the leaking problem center pin. I think it's pity wasn't working well for now bc the taste of e-liquid i really was surprised about this little device brought me, it is amazing good.
Earlier posted:
I can go along with Tbev, atomizers of KF or TF and devices like that don't fail, there performances are great, anyway this topic is about the Rebuildable carto's for tanks and I took a Diver V2 for my just ordered Phini and arrives hopefully soon but I wanted the best Atomizer for my Phini because I think Phini deserves it.
Just trying the Diver V2 for 2 days now and can't say I'am positive about it, the leaking problems of the center pin Atmistique fixed with the 2 O-rings, a poor solution but it works, but now its leaking from the little hole into the center pin and a lot.
I have been informed by advanced that the Diver is very sensitive when it comes to pressure build-up and pressure differences, in short the Diver often if not all the time gives problems with, I think you can imagine that I wasn't happy to hear this at all *sad face*
The problem of leaking all your liquid out of tank when installing the Diver into it, this can be solved by hold the Diver between 2 fingers by the top of the Diver and to the center pin following by pressing really hard at both sides and you ready to bring your cap closer to the tank and place it.
I will not give it up that quickly, so i will make a new setup for this device and hopefully i will find a solution for the leaking problem center pin. I think it's pity wasn't working well for now bc the taste of e-liquid i really was surprised about this little device brought me, it is amazing good.
Good afternoon
The problem is the way you try to fill your tank. And it's a problem because it's very easy to broke your glass tube and also because it's impossible not to have leakage while you try to put the tank top-cap.
Please try the usual by pulling the Diver down until you see the side holes, fill your tank and then return the Diver inside the tank (with the end-caps always on the tank).
At first please try these suggestion and you will see that Diver isn't a "useless device" and also doesn't "all the time gives problems with" maybe because it works to many other people.
It useless to say that if you still have any problem you can always use our thread here and also our email info@atmistique.gr.
Waiting your news
The problem is the way you try to fill your tank. And it's a problem because it's very easy to broke your glass tube and also because it's impossible not to have leakage while you try to put the tank top-cap.
Please try the usual by pulling the Diver down until you see the side holes, fill your tank and then return the Diver inside the tank (with the end-caps always on the tank).
At first please try these suggestion and you will see that Diver isn't a "useless device" and also doesn't "all the time gives problems with" maybe because it works to many other people.
It useless to say that if you still have any problem you can always use our thread here and also our email info@atmistique.gr.
Waiting your news
Hello Konstantinos, while you were making your post, at page 68 or something 
in this topic, I already was reading about and immediately tried this setup and YES It,s working fine now!
I did spoiled a few drips of liquid this way but far not that much like before and is acceptable, after it was still leaking and gurgling... "Oh No not again!", but this was just a few times and all still fine now!
I still do like the "wick out of Diver" method, but unfortunately I think that's not possible bc the Wick needs to pass the cap for filling the tank, anyway it's something I can live with
The tank filler I can use now also, which is also not possible with the "wicks out of Diver" method.
After all I'am really happy vaping works fine now and that's all about, but if you do have a solution for the "wick out of Diver" method, please let me know but don't worries if we have to forget this method.
Sorry I was so impatient Konstantinos, you have saved my day and specialy the poster at that page 68!... Thank you all!
in this topic, I already was reading about and immediately tried this setup and YES It,s working fine now! I did spoiled a few drips of liquid this way but far not that much like before and is acceptable, after it was still leaking and gurgling... "Oh No not again!", but this was just a few times and all still fine now!
I still do like the "wick out of Diver" method, but unfortunately I think that's not possible bc the Wick needs to pass the cap for filling the tank, anyway it's something I can live with
The tank filler I can use now also, which is also not possible with the "wicks out of Diver" method.
After all I'am really happy vaping works fine now and that's all about, but if you do have a solution for the "wick out of Diver" method, please let me know but don't worries if we have to forget this method.
Sorry I was so impatient Konstantinos, you have saved my day and specialy the poster at that page 68!... Thank you all!
Last edited:
- Status
Similar threads
- Locked
