My tracking has not updated since yesterday morning. Its supposed to be here today.
Attack of the Hana Modz Clone. Let's wait together!
- Thread starter Fathomrock
- Start date
- th_trl_thread_readers 0
- Status
OK so one more time I want to see what people think of this. Going to really make this simple.
My daily vape is one of my Provari's and a kayfun.
1.2 ohm coil, 3.8v setting which is 12.03 Watts and pulls 3.16 amps.
Will the Cana mod be able to do this or because setting it at 12 watts will put it just under 4V and not be regulated properly?
Worst case I could rebuild to like 1.5 ohms, set it for 12 watts and it would do 4.24V at 2.82 amps. I could just up the voltage on the Provari to 4.2 and they should be about the same, no?
My daily vape is one of my Provari's and a kayfun.
1.2 ohm coil, 3.8v setting which is 12.03 Watts and pulls 3.16 amps.
Will the Cana mod be able to do this or because setting it at 12 watts will put it just under 4V and not be regulated properly?
Worst case I could rebuild to like 1.5 ohms, set it for 12 watts and it would do 4.24V at 2.82 amps. I could just up the voltage on the Provari to 4.2 and they should be about the same, no?
No worries about that. Its happened to me numerous times. Its just the carrier not doing their job. I've had a ProVari show Washington state until delivery.
Mine arrived at the local post office about 3AM...hopefully that switches to "out for delivery" this today.
Has anyone rec'd a blue unit yet from any of the vendors on pre-order?
I've seen a couple variations of the color and maybe this is due to lighting or color mixture, not sure.
I really like that dark blue ....just wondering if anyone that has rec'd one if they could post up a pic and vendor you used.
Also, are the units being sold from 101 and Elev8 both from Clouper and working properly? Sorry, this may of been mentioned but wasn't interested in reading over 300 pages to get an answer.
Many thanks
~Mike~
I've seen a couple variations of the color and maybe this is due to lighting or color mixture, not sure.
I really like that dark blue ....just wondering if anyone that has rec'd one if they could post up a pic and vendor you used.
Also, are the units being sold from 101 and Elev8 both from Clouper and working properly? Sorry, this may of been mentioned but wasn't interested in reading over 300 pages to get an answer.
Many thanks
~Mike~
Morning coffee and a vape....morning Classy.....
I'll try to answer your question....
The Cana advertising says the minimum output is 4 volts (just as does the spec sheet of the real dna). Therefore trying to get to a voltage of 3.8 is just at the border of possibility. If the Cana is like the real dna chip it is set to regulate starting at 4 volts..Really depends on the tolerance of the chip if it starts regulating at exactly 4 volts.. As far as upping to a 1.5 ohm coil and still setting at 12 watts on the clone should work. The Cana then should operate within it's reported specs...
As far as setting the Provari and cana at 12 watts with a 1.5 coil yes they should be the same if both devices are functioning within specs...
Hope this helps...
EDIT: just a thought....upping the wattage to 13.4 with a 1.2 coil puts you at 4 volts on the canna and tho the vape quality will be different it MAY/MAY NOT give you a good vape??? That depends on what you desire....l
Last edited:
$56.00 HANA MODZ Pack DNA 30 Style Mod - built-in 2*600mAh Li-Po / 7W-30W at FastTech - Worldwide Free Shipping
The 30's are at FT now but w/ li-po
Green only right now, all others including 18650 should soon follow.
*disclaimer, I ain't sell'n nutt'n
The 30's are at FT now but w/ li-po
Green only right now, all others including 18650 should soon follow.
*disclaimer, I ain't sell'n nutt'n
Last edited:
Yeah if I go from 3.8v to 4.1 on the Provari this juice starts to burn. So well see. I've got a bunch of Kayfuns so I'll rebuild one tonight to 1.5 and try it out on the Provari with the voltage upped a bit and just compare the two. If that works I'll be happy.
You have helped me a lot, I appreciate it man.
Your welcome.... oh I failed to mention.... from the real dna spec sheet:
Too low power setting: The DNA 30D puts out a minimum of 4 volts. With low power settings (7 to 8 watts) and low resistance atomizers (below 2 ohms) the DNA will sometimes be unable to provide a low enough power output to be power regulating. If this is the case, the Ohms display will be flashing. The device will still operate.
By that info it will dump battery voltage... unregulated....
Last edited:
The Russian handles 30 watts quite well, know it can handle whatever the Provari can dish out. P was my first regulated, the Russian it's first rba. Sold the Provari and bought a futura30. So I am confident the kayfun can handle P.
Mine is out for delivery. *stalking mailman*. Ordered from 101. As I said earlier in this thread, they were the safe bet for me.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Good, mine from 101 is showing out for delivery also. Glad it made it before the holiday.
Mine from wetvape mailed Thursday still showing it departed Rochester yesterday morning.
Sent from my Nexus 5 using Tapatalk
Sent from my Nexus 5 using Tapatalk
Found something else...my led screen doesn't turn red or green when charging/charged.
Does anyone else's?
Sent from my SM-N9005 using Tapatalk
Does anyone else's?
Sent from my SM-N9005 using Tapatalk
I also ordered from 101. I got green tho, so seems I'll be waiting on it for a minute. I used 101 only because they've been around for a while and I've used them before with no problems. So far from this pre order i got exactly what I expected from 101. On their disclaimer it said approx arrival was mid may. Mid may rolled around and they updated accordingly. A lot of people started harassing venders a good 2 weeks before the expected ship date. Sort of like the kids hollering "are we there yet." I didn't really expect any updates until mid may going into this. 101 is a good reputable vendor, and as I've said before, if all goes to the crapper, I am very comfortabe that I will at least be refunded my money.
Last edited:
I've used my real Hana with my Russian 91%, Kayfun Lite+, Fogger v4, and my Taifun GT. Since in reality the clone is identical in construction I would say you were in the clear. The weight is nicely distributed and has a much more stable footprint than any tube mod and better than the MVP since it is CNC'd instead of having cast end caps. The more defined edges of the base make it less likely to tip over if bumped. On a similar note, RDA/RBA's with long 510 connectors and short threading like the Paradigm Magma seem to be very secure and fit flush without issues and my Taifun GT despite being 23mm does have room inside the machined recess.
Even with the real DNA30 you can feel that saggy lack of power feeling when the battery is next to dead and its plugged into the USB port. Even a USB 3.0 'charge port' can only supply 2A, will obviously not be able to keep up with my .4ohm dual coil'd TOBH @ 26.5w.
Since I have a regular printed J-Wrap on my MVP and a clear carbon fiber VaporSkinz on my Hana it's apples to oranges. The carbon fiber textured vinyl is MUCH thicker that the J-Wraps standard printed stuff. I don't know if the J-Wraps carbon fiber is textured or just printed to look like CF, so maybe someone else can answer that. The J-Wraps shows their Hana skinz as being a '2 piece" design and the Vapor Skinz is actually 6 die cut pieces.
For box mods - Parish leather cases
Amazon.com: Heavy Duty Oversize Large Vertical Smart Phone Case / Pouch / Holster with Belt Loop, Clip, Velcro 5.50 x 3 x 0.75: Cell Phones & Accessories
Amazon.com: STRONG NYLON VELCRO POUCH CASE DUTY METAL BELT CLIP HOLSTER+RING HOOK for APPLE iPHONE 5S 5C 5 FIT WITH BALLISTIC HARD CORE CASE ON IT (by All_Instore): Cell Phones & Accessories
http://vapers-shop.net/en/home/123-vape-vest-holster.html
It's not the screen that changes color. There is a hole approximately .5mm just to the left of the USB port on the real Hana with a LED behind it that illuminates red when charging and goes off when it is full.
On another note, I have also had a relatively smooth experience with IllVapes. They have answered my emails promptly, and the 'non-mass mailing' emails I have received were unique, professional, and courteous. I would challenge anyone to get hit with that {MODERATED} storm and handle it flawlessly. Sure they were selling a logo'd clone, using Hana's pics etc. But you also need to remember they were the first ones to put up a pre-order. At that time the no-logo version may not have existed to their knowledge or Cloupor may have been using them as guinea pigs to test out the demand for the logo/no logo versions, and there was no other vendor to price against. Why would they have expected to get sued when virtually every vendor sells some 1:1 clone (some that even have the boxes and COA's duplicated)? At least they came out within a day or 2 and made a public statement regarding the lawsuit. Look at Ebay for example. The data breach in February involved 145 million customers and they waited 3 months to lets us know maybe we should change our passwords. {MODERATED}
Last edited by a moderator:
Mine was red when charging and green when charged. There's no hole over the led so its just a faint glow if you check it in the dark.
Sent from my SCH-I535 using Tapatalk
- Status
