Here is the inside of mine. Looks like the buttons and such are epoxied in. The hot glue is just on the red window. Hope this helps ease some worries
Sent from my HTC One_M8 using Tapatalk
Attack of the Hana Modz Clone. Let's wait together!
- Thread starter Fathomrock
- Start date
- th_trl_thread_readers 0
- Status
Here is the inside of mine. Looks like the buttons and such are epoxied in. The hot glue is just on the red window. Hope this helps ease some worries
Sent from my HTC One_M8 using Tapatalk
Just another video review i found hana modz V3 The Perfect Clone? DNA30D: http://youtu.be/efV6V2LTncE
Sent from my SM-N900T using Tapatalk
Sent from my SM-N900T using Tapatalk
I'm sticking it out with illvapes also...for now.
I'm also still trying to find an authentic hana in green, and at this rate I may find it first.
I'm also still trying to find an authentic hana in green, and at this rate I may find it first.
Last edited:
I would say just buy the lipo that the real hana uses i think they go for around 10 or 15 bucks
Sent from my SM-N900T using Tapatalk
From what I figured out so far... it can read a resistance of .3 to 3.3. Less than .3 will show a short. It will regulate between 4v and 8v. So my .6 ohm coil will run unregulated at 10 watts, and run regulated at 30 watts. If you run a coil at roughly 2.2 ohms, the whole 7-30 watts will be regulated.
Sent from my SCH-I545 using Tapatalk
Mine stripped as well. Don't use a screw extractor/easy out because the screws are so cheap they easily come out with a drill. Use a small drill bit and drill the screw head off. It doesnt take much effort so go slow. You will need replacement screws and they are M2 x 10mm that's what worked for me. I also replaced the other screw as well. You can get the screws at Ace Hardware.
Besides the screw issue, I really like the device
Where did he get one with a logo. Hana is going after anyone trying to sell those. Im perfectly happy to have one without the logo. I plan on using it as a project box for future chips. As long as the screens remain the same.
Sent from my SCH-I545 using Tapatalk
I don't know were he got the logo one from but you know when hana finds out they will go after them
Sent from my SM-N900T using Tapatalk
Seems like there are a couple of videos on YouTube today of people with logo units
Sent from my SM-N900T using Tapatalk
Sent from my SM-N900T using Tapatalk
You can get very high quality LiPos for about $5. I'm about to throw in 2 1200mah 30A batteries in parallel (for a single battery of 2400mah 60A) in an SX350 box.
Each one is just under $6.
Either way, I'd rather not have to go through whatever mess of soldering/epoxy they'll use in order to change the batteries out.
What I'm really after is a mini-sized box that has a window for the SX350. I'm using small project boxes now, but I'd love to have a billet aluminum box.
Batteries are charged and it's in the Silver from Wet Vapes. Vaping a 1.4Ω KFL+ v2 (EHPro) at 14W. Very smooth. Buttons are nice and clicky.
The biggest con thus far is that the Silver is a finger print magnet. It's not as bad as polished stainless, but I've only been holding it for a few minutes, and my prints are everywhere. But that's no fault of the MOD, but the material.
Sent from my iPhone using Tapatalk
The biggest con thus far is that the Silver is a finger print magnet. It's not as bad as polished stainless, but I've only been holding it for a few minutes, and my prints are everywhere. But that's no fault of the MOD, but the material.
Sent from my iPhone using Tapatalk
My wife notified me my silver has arrived and is sitting on the kitchen counter. This next hour and a half at work is going to be torture.
The black is a finger print magnet as well
Sent from my HTC One_M8 using Tapatalk
Sent from my HTC One_M8 using Tapatalk
Yes it is, thought it was just me. I ordered the Jwraps black carbon fiber for mine today. I have to constantly clean mine because it gets slippery from the oil in the fingerprints. Hopefully the wrap will solve this.
If you read all 4000 posts you will find that I have stated this approx 4 times, I think I just might make this my sig line
anodization can and will have color variation from batch to batch.
If you read all 4000 posts you will find that I have stated this approx 4 times, I think I just might make this my sig line
anodization can and will have color variation from batch to batch.
If you read all 4,000 posts you would notice that the person who took the pictures said it was just different lighting.
1) in that particular anecdote that may be so.
But it doesn't change my statement. This is nature of the beast esp when mass produced.
Ive seen this for as far back as I can remember in the firearms world, not one off backyard mechanic projects or the like.
2) actual Hanas display variation as well. Care to guess why?
- Status
