Attack of the (Kayfun Mini V3) Clones!
- Thread starter KTMRider
- Start date
- th_trl_thread_readers 0
- Status
If we can get the EXACT sizes of these o-rings, I think that this site, The O-Ring Store LLC, We make getting O-Rings easy! would be a great place to get some good quality o-rings.
I am chatting with them about these o-rings. They are emailing me some information about these o-rings. Be right back...
I will say this about the Mini v3 Plus, it is crazy forgiving for nOObs to RTAs.
All the coils I've rebuilt so far was my Turbo Evods and GS Airs. I accidentally wound my first mini v3 coil with 32 gauge Kanthal. Oops. 3.2 ohms. What the heck I thought, lets see what happens. At first I had a pretty massive juice leak, I think out of the air holes but I guess that was nOOb operator error. I cleaned it up and all is ok now. I prefer a cooler vape and even with this way too high coil it still vapes pretty well.
I've already got another coil wound from the thickest I have 30 gauge at 7 wraps at 2mm. That will probably ready higher than my 1.5 preferred but if the 3.2 vapes this good even a 1.8-2.0 ohm should do pretty well too.
I will say that capturing the coil legs is At Least as fiddly as rebuilding the GS Air coils though.
I would appreciate it very much if someone who has cut capture grooves into the deck would show a pic of them. I assume that's a Dremel job, right?
Bruce in Ocala, Fl
All the coils I've rebuilt so far was my Turbo Evods and GS Airs. I accidentally wound my first mini v3 coil with 32 gauge Kanthal. Oops. 3.2 ohms. What the heck I thought, lets see what happens. At first I had a pretty massive juice leak, I think out of the air holes but I guess that was nOOb operator error. I cleaned it up and all is ok now. I prefer a cooler vape and even with this way too high coil it still vapes pretty well.
I've already got another coil wound from the thickest I have 30 gauge at 7 wraps at 2mm. That will probably ready higher than my 1.5 preferred but if the 3.2 vapes this good even a 1.8-2.0 ohm should do pretty well too.
I will say that capturing the coil legs is At Least as fiddly as rebuilding the GS Air coils though.
I would appreciate it very much if someone who has cut capture grooves into the deck would show a pic of them. I assume that's a Dremel job, right?
Bruce in Ocala, Fl
I Definitely notice the Stouter nic dose delivery of the RTA over my GS Airs.
I was already considering dropping my nic from 12 to 6 and the KF may actually help a lot with that. I can use the GS Airs under normal stress situations and go to the KF when I need a little bump back up in nic dosing.
Bruce in Ocala, Fl
I was already considering dropping my nic from 12 to 6 and the KF may actually help a lot with that. I can use the GS Airs under normal stress situations and go to the KF when I need a little bump back up in nic dosing.
Bruce in Ocala, Fl
So which one fits the bottom of the base? I am thinking it might be 1mm x 7mm, or else 1.5mm x 7mm
There are 4 of each tho... and $6 shipping
. I don't even need these. I was just trying to help whoever needs them.
Ya did good Ricks!!!There are 4 of each tho... and $6 shipping
I just think that, the authentics would be a much better value for all who may have Kayfun Mini V3 O-Ring issues.
Jim
KFM3 with KF4 chimney extension, and a spare glass tube I had lying around for my EHPro Buddha Mini, walls are a little thick @ 1.5mm but work fine. Unfortunately the glass is very hard to source. Glass is 35mm tall 18mm od, 15mm id.What IS that?
with the following two items you'll end up with a longer higher capacity glass tanked KFM3.
IBTanked has custom cuts 18mm with 1.2mm walls any length from 10-40mm minimum 3 pieces which will cost $21 plus shipping.
18.0mm x 1.2mm Custom Cut Tubes
$4.59 Replacement Tank Set for Kayfun V4 RTA Atomizer - stainless steel + glass at FastTech - Worldwide Free Shipping
Last edited:
Oh didn't know we were in the presence of a mechanical genius. 
Very cool. How much liquid does it hold?
Very cool. How much liquid does it hold?
- Status
