Boro Mod's, Tanks, Attys And More

[Pigs]

You did a really nice job T.

Thanks J!

Awesome job, T.
You can be proud of the end result, simply delicious!!!
Inner panel on the one on the right, I really liked it, do you have a link to share on that part?

Thanks Tor!
This is the one, Looks like they're sold out at 3f now.

 

[BillW50]

Since we were on the subject of grounding, I borrowed some tips from @Steamer861 for you to enjoy.

 

[BillW50]

I guess I should have added this footnote a few days ago. I thought about it, really! But I believe I should mention this for the time capsule. As the San AIO was released on 20 DEC 2023.

We're still waiting on the Pulse AIO v2 and the Aspire Raga. Hopefully they will be released soon.

 

[Pigs]

Since we were on the subject of grounding, I borrowed some tips from @Steamer861 for you to enjoy.

View attachment 1005531

I'm over mucking around with the small stuff.

 

[crss]

Wired up my new camo frame this morning.
View attachment 1005509

View attachment 1005511View attachment 1005512View attachment 1005513View attachment 1005514

Did you install up/down switch & ground wire to frame & then solder to dna60 board? I solder all to dna board (Last step ATTY OUT) wire, dna propped up in frame to solder. Flashing 2 dna boards tonight. ATTY out wire glued into red/purple frame.

 

[crss]

 

[Pigs]

Did you install up/down switch & ground wire to frame & then solder to dna60 board? I solder all to DNA board (Last step ATTY OUT) wire, DNA propped up in frame to solder. Flashing 2 dna boards tonight. ATTY out wire glued into red/purple frame.

I installed/sealed atty positive (with its wire) in frame, then battery positive assembly (with its wire) in frame, then up/down pcb (with its 3 wires and used double-sided tape to hold in position on frame), then 2x ground wires screwed in to frame.
Then I soldered all wires to DNA board. Last step I put the screen in position and connected to board.

I think one of the trickiest things is how long to cut the 2 x ground wires so you have enough room to work, but also can push the board into place and screw down with the inner plate. If the wires are too short, you can't manoeuvre, but if the wires are too long the board springs up and you can't close it properly.

Vaping with Qbix now

 

[crss]

Beautiful Pigs

 

[crss]

One hour with a dremel, got a perfect fit. Yes a usb port on Rainbow round button plate set.

round_rainbow+USB

 

[crss]

I solder all to DNA 60, leaving hot wire to atty as last solder.

 

[Pigs]

One hour with a dremel, got a perfect fit. Yes a usb port on Rainbow round button plate set.View attachment 1005563View attachment 1005564View attachment 1005565round_rainbow+USB

Looks amazing!

 

[badinfluence357]

Merry Christmas to all.... A little something to get me get through the holiday's.
For some reason this Christmas didn't feel so festive but I did enjoy the grandkids shredding through wrapping paper. Then I became Bob the builder at four o'clock in the morning!!! Astro and Orbit, Tycoon and Droid

View attachment 1005745

 

[badinfluence357]

Wired up my new camo frame this morning.
View attachment 1005509

View attachment 1005511View attachment 1005512View attachment 1005513View attachment 1005514

@Pigs, Can you send me a close up picture of that paper wiring diagram of the Dna 60...

 

[ShowMeTwice]

DNA 60 wiring.......

Taken from Evolv's DNA 60 spec sheet - PDF attached below.

 

[ShowMeTwice]

 

[Pigs]

@Pigs, Can you send me a close up picture of that paper wiring diagram of the Dna 60...

SMT posted both the wiring diagrams I used . The common ground on the up/down button wiring is one to keep in mind

 

[Tor R]

I solder all to DNA 60, leaving hot wire to atty as last solder.View attachment 1005566

What type USB card is that, crss?

SMT posted both the wiring diagrams I used . The common ground on the up/down button wiring is one to keep in mind

Questions about switch connections to the chipset, do you need to use the - points on the chipset, or should - and + to fire switches?

 

[Pigs]

What type USB card is that, T?


Questions about switch connections to the chipset, do you need to use the - points on the chipset, or should - and + to fire switches?

Sorry Tor - a bit confused about that post. Looks like the usb card that @crss showed there might be an evolv unit but not sure. I have one but decided to use my floating usb dongle instead - basically a lazy soldering

 

[Pigs]

Pulse AIO V2 has shipped

 

[Tor R]

Sorry Tor - a bit confused about that post. Looks like the usb card that @crss showed there might be an evolv unit but not sure. I have one but decided to use my floating usb dongle instead - basically a lazy soldering

Hehehe I wrote very chaotically. Have been corrected to crss.
It is not a standard Evolv USB since the port is at 90 degrees to the solder points for the wire.

chipset to switch, do you have to use + and - from pcb, or can it be done as we do on dicodes and take from - battery to switch then to chipset?