I'm looking to pickup this guy and was curious about the negative experiences anyone has had With it. The site selling it has tons of food reviews but I'd like to hear of any potential downfalls before I drop 70-80 bucks on a rba. I'd like a bottom fed style setup mostly I know using my vivi Nova ATM is fine but not perfect . And the only other one that caught my eye was the "Pali v4" although it has no feedback from what I could see
Bullismoker A2-T vs ??
- Thread starter sacricide
- Start date
- th_trl_thread_readers 0
-
- Tags
- litecigusa vamo
- Status
Oh no, I think a leak would be a deal killer at its price for me. Where does it leak from the mouth peice tank???
sacricide:8354737 said:
If you have used Ego C before, you will know what kind of leak i am talking about.
The liquid leaks from the spike hole, and got sucked into the air path and eventually to your mouth. So i keep sucking juice in my mouth.
I also very upset by this, because of the leaking of Ego C, but i really like the system. So i bought Bulli, hoping that i will not leak, but i was wrong
oh wow, i understand...thats annoying. have you tried to exchange it maybe yours is defective???
i might have to try a different RBA, but theres not many that have bottom fed coils.
Hi sacricide, Im looking at that Bulli also. All I can tell you is My Joyetech ego-c never leaked, but sooner or later anything can leak.
Im thinking, made in Germany, is usually good quality. Never tryed a RBA yet, and when i do, i would like to get a good one.
Where are you seeing the Bulli? I see it at VaporCigzz.com
yes vaporcigzz is the only USA site i can find it at. i may still try it out. its a hard decision because this PALI V4 is also bottom coil, and its less than 20 bucks. Pali V4 Stainless Steel R/A Tank
Cuecig.com has the Bulli and offers a 200% price match if you find it cheaper just got a vamo from him and it arrived in 3 days he is in Atlanta wich is a major postal hub
Bully V3 Rebuildable Atomizer Mod - Cuecig.com
Bully V3 Rebuildable Atomizer Mod - Cuecig.com
Hi Cid78, I dont know why i had such good luck with the Joyetech ego-c. I bought from Litecigusa and the tanks came with holes already punched. I read that lots of people have had to punch holes? In any case, I quit smoking with it in June and only used it for 2 months before moving on to clearomizers. I believe that this same tank fits the Bulli and your probably right that the tank is not made in Germany.
The A2-T takes Joyetech type A tanks according to Vaporcigzz. I can't find for sure what tank for the A2-TM, maybe type B?
Judgement, yes the A2-TM is using the Ego C / T tybe B tank.. I chose Type B because of bigger tank..
Anyway, i tried another tank, and today it has not been leaking. Possibly last leak was because of the tank... Will use it for several days and observe..
And also will try to built with SS mesh wick to see whether the flavor get better with SS mesh wick..
you need to take out middle plastic seperator from the type b tank and type a cardrige, put a needle in take the first tip out take second out and put the first one back in. Otherwise it creates too much suction and that is why it leaks. Hope it helps
Hi bydus,
You might be right, I always did remove one or the other for better draw.....both didn't seem to change anything for me.
Hope you have better luck Cid.....no leaks.
Please do keep us informed on the Bulli-TM. I for one am interested in anything you have to say.
I keep the one at the end cause once you vape vapor leaves some juice inside the tank but not in your mouth- in short I just took the middle one out and kept the tip one. I have no problems. I just made a amazing setup of 3 strands of silica wrapped 3 times with twisted 0.15 wire comes out to be 1.5ohm and its amazing on ego, I have no leaks now at all I will post pics if you like. Im using an oxidised mesh for wicking juice onto the coil (with no wick inside) I've read about this method somewhere on the ukvapers forum (i would have to look for the link for you)
May I ask whay juice do you vape? Is it 100% pg ? if so it might be to wattery and therefore you have leaks (I use 50/50 pg/vg) I've also noticed that if you are quire low res like I am and heat up atty too much (chain vape for 5 min) then it sometimes leaks. I don't do that often but noticed it happens.
When I first got bulli i made a good wick at first go but then I changed the mesh for wicking and strands and couldnt get a good setup since, i got sick of it and sold it and bought a new one again once I've read about 3 strand method. Now I think its best vape i've had in a while as draw is amazing on these and I always liked type b atomizers. In summary it can be setup properly but needs some try and error. Also I've also noticed that new coil takes some time to break in (few hours) but after that it gives you more vapor and flavor. If you have any questions let me know
Hi Bydus,
Very good information, thanks mate... I just figure it out that the first tank got leaking poblem because the hole is not align with the spike wick, 2nd tank work better. But i still got leak because of over wicking, so the juice flooded the coil, not so good..
Made another wick, so far so good, not leaking.. My juice is 100% VG from Vigin Vapor, although it is 100% VG, but it is thinned, so the viscosity is quite low, similar to PG based liquid.
By the way, what do you mean by 3 strands method?
Very good information, thanks mate... I just figure it out that the first tank got leaking poblem because the hole is not align with the spike wick, 2nd tank work better. But i still got leak because of over wicking, so the juice flooded the coil, not so good..
Made another wick, so far so good, not leaking.. My juice is 100% VG from Vigin Vapor, although it is 100% VG, but it is thinned, so the viscosity is quite low, similar to PG based liquid.
By the way, what do you mean by 3 strands method?
- Status
Similar threads
- Locked
- Locked
