Catfish Atty Mods the next Chapter

[Tbev]

Anyone open up the flow on an omerta? It's a pretty tight draw yeah?

 

[Henry Etta]

Can anyone post builds of their Manta? Kinda struggling to find the flavor. Ive got a 27g dual coil build at .4 or so. Sort of meh. Should i go lower? Thanks

Jeebus, how the hell do you make these pics smaller??
This is a pic of a build I had in mine, twisted 29g @ .55ohms.
This didn't work that well for me, though... sure seemed like it should've. When I opened the airflow up it (2 or 3 holes) it was great. Just didn't work so well for 1/2 a hole...

 

[Henry Etta]

Anyone open up the flow on an omerta? It's a pretty tight draw yeah?

Top air, yes, but side can get kinda airy. I could still do a very restricted lung hit with both top holes opened all the way.

 

[Rule62]

Are there authentic Rogues still? If so, I'll take one. Should I send separate shipping, or can it go in the same box as the Manta I sent payment for earlier?

 

[Magaro]

Friday night entertainment:

Talos Mod by Cigreen

Cigreen: Life two steps beyond the edge of the cliff.

 

[kingdal]

Thanks Rule and Henry. Looks like i should be raising my coils so they're closer to the top airholes. I also see from Henry's pics there's room to move them out from the posts a little. Will give that a try

 

[inspects]

Catfish....finally got your Derringer coiled today....damn...its really an incredible atty.....

 

[LittleBird]

Catfish....finally got your Derringer coiled today....damn...its really an incredible atty.....

Whoa! May be an incredible atty, but that mod is gorgois!

 

[Steelgirl]

Hi, Rogue I got from Tom is really nice, but I need atty with more airflow and better clouds. Derringer and Troll non bf at approx. .7 ohm have nice thick vapor...was expecting the same with Rogue. Whats in stock ? Any suggestions? Or do I just need to lower the ohm build? I really like keeping it at around .7 and for sure nothing lower then .5 Maybe Hellboy? A couple weeks ago I wasn't sure about Hellboy, but the more I look at it, the more it's growing on me. Or maybe a Derringer if any in stock. I love the Derringer too ! Not heard of the Lancia I saw a couple posts about it above my post. Thanks.

 

[Henry Etta]

Thanks Rule and Henry. Looks like i should be raising my coils so they're closer to the top airholes. I also see from Henry's pics there's room to move them out from the posts a little. Will give that a try

As others have mentioned, be real careful about moving them out too much... not a whole lot of space in there. Just be sure to check with a meter before firing! I think mine were as close as they could be.

 

[havok333]

Hi, Rogue I got from Tom is really nice, but I need atty with more airflow and better clouds. Derringer and Troll non bf at approx. .7 ohm have nice thick vapor...was expecting the same with Rogue. Whats in stock ? Any suggestions? Or do I just need to lower the ohm build? I really like keeping it at around .7 and for sure nothing lower then .5 Maybe Hellboy? A couple weeks ago I wasn't sure about Hellboy, but the more I look at it, the more it's growing on me. Or maybe a Derringer if any in stock. I love the Derringer too ! Not heard of the Lancia I saw a couple posts about it above my post. Thanks.

Sorry Steelgirl, thought the Rogue would be roughly equivalent in air to the Derringer for you. Sounds like you need badazz airflow! [emoji16]

I can confirm the REMatty has more air than a Rogue could hope for, and is tiny like a Derringer but with top air.

 

[Steelgirl]

I'm not sold on top air attys like Rogue and REMatty. The Rogue is very nice, no doubt. But not much in the cloud factory.

 

[havok333]

I'm not sold on top air attys like Rogue and REMatty. The Rogue is very nice, no doubt. But not much in the cloud factory.

I admit the Rogue is not much a cloud atty, but it does pretty good if you build the coils high, close to the air. That's what I always did.

I'm such a slacker I haven't even built my Bonsai or Haze yet, but the former SHOULD be similar to a Derringer for airflow. The latter a bit more.

 

[Nautilusfan]

Are you on the CAM-M list? If so you might want to wait on your tool acquisition. Just saying.pretty much every atty I touch that uses grubs can be serviced with the following:

.035" cyclones, other 14mm attys
.050" Derringer, Remm with alternate grub screws, most Murican attys.
1.5mm pretty much all the others with hex grubs.
4mm flat blade screwdriver CH Rogue
3mm Phillips screwdriver most clones and odins.

Tom has given me lots of great advice but this tool list is best money I've spent for vape accessories!! I went all out and bought Hudy Drivers. Seems kind of pricey on first look but like I said a great investment.

 

[Steelgirl]

Hopefully Tom will chime in soon and rescue me once again Havok, how many attys do you have anyway? a hundred or so ?

 

[Rule62]

Tom has given me lots of great advice but this tool list is best money I've spent for vape accessories!! I went all out and bought Hudy Drivers. Seems kind of pricey on first look but like I said a great investment.

I have a set of Wera hex drivers. Love them. Great investment. Lots better than fooling around with 'L' hex keys.

 

[Nautilusfan]

Only a 100 Havok? You're falling behind

 

[havok333]

Hopefully Tom will chime in soon and rescue me once again Havok, how many attys do you have anyway? a hundred or so ?

LOL, wife might agree with that assessment! Maybe 25 if I'm lucky, haha.

I can say, Henry Paul Band is awesome. Wife and I have them jammin tonight. "Grey Ghost" he wrote for Ronnie Van Zant after the plane crash, and now is lead vocals for The Outlaws band.

 

[distortoblotto]

E-mail and funds sent for the Manta and Rogue...

 

[jbmcdan]

pp and email sent for hornet -- thanks, Tom!