Thank you, Tom. The Rogue that you sent my way has been absolutely great, so there was no doubt that I'd be back. As I said, the only reason I'm back on the market is due to cramped deckspace, and a bit of a spin on the center post now that I'm working with heavier wire. I was originally looking for something similar to the CLT V2 or Mutation X V2. Sloth and RuDawg are both impressed by the Vector, and after looking into it, It does appear to have a little more room to work with and a sturdier build. Do you happen to have any of those on hand? If so, which version do you stock? I've seen versions with and without heat sink rings.
Catfish Atty Mods the next Chapter
- Thread starter Chowderhead1972
- Start date
- th_trl_thread_readers 0
-
- Tags
- bottom feeder
- Status
I'd be interested in hearing about the 510 as well. I haven't found any fault in my Cam-M except for the firing button being a little janky. I ended up using some nolax out of desperation & it's been fine since I did it over the weekend. Not the most responsive fire button as you have to know exactly where to push to make it fire but it's working. Other than that it hit's like a bag of hammer's, really makes me a fan of dual 18650 squonking.
I also like my Cam-M! I do have to tear it down a little too often for cleaning. I've got a strange leak and was wondering if anyone else has this issue. The inside of the mod is dry, where the bottle and batteries are. The top of the mod is dry. I get juice inside the top piece and the button contact is wet and in between the copper positive top piece and that white delrin sheet gets saturated. Where can that leak be coming from and how do I correct it?
Sent from my HTC Desire Eye using Tapatalk
Sent from my HTC Desire Eye using Tapatalk
I notice a little seaping in that area as well, not bad but definitely there. I wonder if that's the 510 issue Tom mentioned?
Well, I am the lucky SOB that got a hold of the prototype LBC 
This is my first LIPO and DNA200 device.. I will post a more detailed review tomorrow
But first impressions are holy s***... This thing is awesome...Running a Kennedy 22 on it with dual claptons coming in at .3 Ohms.. These two are made for each other....
This is my first LIPO and DNA200 device.. I will post a more detailed review tomorrow
But first impressions are holy s***... This thing is awesome...Running a Kennedy 22 on it with dual claptons coming in at .3 Ohms.. These two are made for each other....
Well, I am the lucky SOB that got a hold of the prototype LBC
This is my first LIPO and DNA200 device.. I will post a more detailed review tomorrow
But first impressions are holy s***... This thing is awesome...Running a Kennedy 22 on it with dual claptons coming in at .3 Ohms.. These two are made for each other....
Very nice! Be sure to download EScribe and start playing with everything the DNA200 can do!
Will do... Just looking at Evolve's site now
It's probably time for a new bushing. Tom sent a length of tubing with the mod. That's for the bushing in the 510. If you remove the pin in the 510, you'll see it. Pull that one off and install a new piece of tubing. Slide the tubing up to the head of the pin leaving 3 or 4 threads protruding out from the bottom. That should work with most attys.
I'll give it a try. It's actually done that since I first got it. Maybe it was slightly damaged from the git go. I don't know. I'll try that and see if it helps. Thanks!
Too small a piece of tubing or too big a piece (causing it to squash) will result in leaking.I'll give it a try. It's actually done that since I first got it. Maybe it was slightly damaged from the git go. I don't know. I'll try that and see if it helps. Thanks!
It's done. The old insulator was a little raggedy looking and probably wasn't making a good seal. I'll see how it does now. Thanks for the help!
Anyone have the link to McMaster Carr for the high temp tubing for the cam-m? I have the first run cam-m that came with the regular tube. Was looking to get some more because you know... Zombies.
Well, I am the lucky SOB that got a hold of the prototype LBC
This is my first LIPO and DNA200 device.. I will post a more detailed review tomorrow
But first impressions are holy s***... This thing is awesome...Running a Kennedy 22 on it with dual claptons coming in at .3 Ohms.. These two are made for each other....
Question... does the new 22 Kennedy air hole design keep it from leaking like the previous Kennedy atties?
Kentastic
No leaking as the internal air pipes are fairly tall, but with the softer bottle I had to make sure I didn't over squonk
Nice glad to hear I've got an extra Kennedy in waiting for the cam rWell, I am the lucky SOB that got a hold of the prototype LBC
This is my first LIPO and DNA200 device.. I will post a more detailed review tomorrow
But first impressions are holy s***... This thing is awesome...Running a Kennedy 22 on it with dual claptons coming in at .3 Ohms.. These two are made for each other....
Sent from my LGL33L using Tapatalk
- Status
Similar threads
