Confusion about Aug 8
- Thread starter smokin95
- Start date
- th_trl_thread_readers 0
- Status
Although I agree that Efest are not of the same quality as AW, the Efest red IMR batteries have performed well in my ProVari 2.5's. The ProVari 2.5 doesn't require a extremely high amperage battery as they don't support subohm vaping and the Efests meet their requirements. Although Efest has been known to exaggerate their battery specs in some cases, all their IMR's exceed the required amps of the ProVari 2.5.
If they are abused yes they will blow up ot vent.
The problem they lie about their batteries and you don't know you are stressing the batteries until you have a problem.
Do you know where to get the parts state side? I was thinking about buying a couple of those tanks from Mr E if they still have them in stock, since they are cheap and in my home state, for my housemate to use after she destroys all the nautilus bases or runs out of coils.
There's a blog with sizes and sources for screws and O-rings for Kayfun Lite and 3.1.
https://www.e-cigarette-forum.com/forum/blog-entry/kayfun-replacement-o-rings-and-screws.6169/
Kidney Puncher has the insulators in packs of 5.
Mad Vape has plastic tank sections for $1.50, you have to do age verification and they don't sell to some states. You can get them from FT, pack of 3 for $1.60.
EVCigarettes sell screws and orings and other parts individually, a little expensive and some of them are out of stock.
Lightning Vapes have some parts.
https://www.e-cigarette-forum.com/forum/blog-entry/kayfun-replacement-o-rings-and-screws.6169/
Kidney Puncher has the insulators in packs of 5.
Mad Vape has plastic tank sections for $1.50, you have to do age verification and they don't sell to some states. You can get them from FT, pack of 3 for $1.60.
EVCigarettes sell screws and orings and other parts individually, a little expensive and some of them are out of stock.
Lightning Vapes have some parts.
Another thought on Kayfun parts. The KFL is on sale for $10 now. They come with spare screws and O-rings. Plus you get the insulators and all the other parts on the tank itself. If you add up the cost of all the parts you get with a tank I'm sure it would come to more than $10. The only stuff I got separately was insulators and plastic tank sections since you only get one of each with a tank. You can get the screws and O-rings from non-vaping sources.
I think that most things will be available after 8/8. The retailers just need to restock. It's down the road that we may have problems. 8/8 is the beginning of the end if we do not overturn the Deeming Regs.
mister e has them also but my transaction/card was declined for some unknown reason even though the funds were placed on hold/pending according to my card website.
I am afraid we are going to be seeing a lot of this while the bugs are worked out of the verification process
had the same thing happen at viper-vape. I am done shopping (just placed a few small orders (mostly diy stuff, and a couple STM clones) in addition to those 2 that didn't go thru properly). I have a few more carts loaded with mods and rda's from state side vendors I have bought from before but those will have to wait a month or two until I get my CC's back under control.I am afraid we are going to be seeing a lot of this while the bugs are worked out of the verification process
OriginVape site shipped immediately. They do if they have the item in stock - and it tells you at order time on their website if they have it.
Looks like they don't have any clones, little pricy for a noob :/
And vapor range does offer priority shipping. Might try my luck with madvapes they do have the clone
- Status
Similar threads
- Locked
- Locked
- Locked
- Locked
