confusion on my new ingulgence

[WillyB]

HeHe yup di there 3.2v at 1000mah

I got fed up with the cap fading color. so I took off the paint from the cap.
aluminum/copper hehe. So now I have a copper colored cap with titanium body.
Hopefully When the paint shop gets time I will clean this up & get it painted some off the wall color.

But 6v is actually 6.4v I popped my very first atty that was a yr old.got about a 1s hit hehe. down to 1 401 Awaiting more.

That's a tough call, in loaded tests using the standard 3V Tenergy LiPO's with a Joye 510 atty will give you about 5.18V while actually vaping.

Tenergy LiFePO4 RCR123A 3.0V 750mAh Rechargeable Battery

It's hard to say if these EM LiPO's will perform the same.

 

[Di]

Has anyone triad if their 3.2v 1000mah LifeP04 work with cartomizer???

mine worked for about 30 seconds with vapornine turbo cartos. they have a reading of 3.1ohm's.. then it seems as though the pcb kicked in, because they stopped working, but placing the carto on 3.7v it was back to working.

That's a tough call, in loaded tests using the standard 3V Tenergy LiPO's with a Joye 510 atty will give you about 5.18V while actually vaping.

Tenergy LiFePO4 RCR123A 3.0V 750mAh Rechargeable Battery

It's hard to say if these EM LiPO's will perform the same.

ok,

mine will not work with 510 regular atty nor with regular carto

but it works just fine with regular 801 and regular 901

hahahahahahha

go figure !!!!!!!!!

 

[Kuya Dave]

Wow Di you finally tried it.
mine work with every atty I have thrown at it.
401 510 808 801 at 6.4v

 

[Di]

Wow Di you finally tried it.
mine work with every atty I have thrown at it.
401 510 808 801 at 6.4v

I just got it last night
so I couldnt try it before--

I have had Indulgence for ages,

but not the 6Volts extended cup and 2 x 3volts batteries---

so I just got these last night,

I tried it all today

and this is what I found-------

combination of 2 x 3v battys in extended cup +510 reg atty
NO Worky

combination of 2 x 3v battys in extended cup +DPV9 carty reg atty
NO Worky

combination of 2 x 3v battys in extended cup +401 reg atty
NO Worky


combination of 2 x 3v battys in extended cup +801 reg atty
Worky Good


combination of 2 x 3v battys in extended cup +901 reg atty
Worky Good

 

[ricardofmf]

my 901 regular atty not work @6v , i dont have the 401 or 801 atty to try .

 

[Di]

my 901 regular atty not work @6v , i dont have the 401 or 801 atty to try .

more and more

interesting, -- veeeeery interesting


I am sure the engineers will come up with an answer soon ----

 

[Kuya Dave]

hmm i like my 901 at 6v
best it actually has been.
just found it yesterday LOL..
but i think i will include it into my 401 801 then 901-6v
great vapor & decent taste at 6v Regular atty

 

[Apatel]

I love the regular 801, 901, and 510 with the 6v extended cups, but so far I killed all three attys at 6v, they only lasted for about 30 minutes and then died. I kept them as wet as possible....what gives? Besides the fact that they are 3.7v attys.

 

[Di]

I love the regular 801, 901, and 510 with the 6v extended cups, but so far I killed all three attys at 6v, they only lasted for about 30 minutes and then died. I kept them as wet as possible....what gives? Besides the fact that they are 3.7v attys.

nothing gives,


3.7v attys are not sposed to run at 6V -- they will blow

thats why the HV attys are made.

some peeps are lucky and manage to run them at 6V but it is lucky if it works for any length of time.

 

[Kuya Dave]

well I ran a 901 yesterday for the full length of the batteries.
2x 3.2v freshly charged. now there 2.78 lol put them on charger today
the 901 is 3.7v atty I finally found it on my messy desk.
OMG the flavor finally from it & vapor was good.
after the battery died I tried at 3.7 and no go to light for me.

Couldn't find my 401 that I dropped. So went back to my normal

Good luck all
Im taking a minor break.
My shoulder is killing me bad enough

 

[mudmanc4]

Well yes of course they died , as di said, you should use the HV atomizers with anything over 3.7 v

I use standard atomizers at 6 v, but I "tap" the power button, I never just hold it, I learned that by doing exactly what you did. No standard atomizer should be expected to take 6 volts and live.

rick

I love the regular 801, 901, and 510 with the 6v extended cups, but so far I killed all three attys at 6v, they only lasted for about 30 minutes and then died. I kept them as wet as possible....what gives? Besides the fact that they are 3.7v attys.

 

[Apatel]

Oh, but it's so good while it lasts

 

[jcamacho]

Same thing here,regular atty at 6 volt will not work, HV atty from EM works fine. Is it because EM wants us to buy HV attys from them? I also tried reg 901 atty at 3.7 volt and it didn't work, then I used a 901 LR atty and it fired right up. None of my other mods do this, I can use reg atties at 6volt all day everyday without problems but they won't work on this unit, this kind of sucks!

 

[doots]

Has this issue not been solved?

 

[jcamacho]

Not for me.

 

[doots]

maybe they should stop selling them until an answer is posted..

 

[Apatel]

This may be OT, but I was wondering if we can use the HV atomizers with 2 of the 3.7V batteries in the extended cup?

 

[jcamacho]

HV atties seem to work at 6 volt, looking for other HV's can't seem to find as I only had a couple and they got mixed up with my other atties. I normally just use normal atties for my hv vaping, don't take long hits just short 1 or 2 sec hits. They seem to work out alright with all my other mods including 5 volt mod boxes. When I tried a normal atty on the Indulgence tonight-nothing. I thought maybe I had blown it at first but then I tried it on another mod at 6 volt and it worked just fine. An HV atty came with the kit I just bought and I tried that and it worked fine. I then tried a normal 901 at 3.7 volt and nothing again. I tried an LR 901 that I just got from Altsmoke and it works! I don't know what the problem is, this is the first mod I've had that works this way.

 

[Di]

This is the answer we got from the engineer ---------

the regular 510 atomizer ohm is 2.1 , too low,
and so the PCB inside shuts down the power automatically for protection --------

that is why if we put the other normal atomizer which is from 2.7 to 3.3.,( 801 901 401 )

and the HV attys which are designed for this HV -(6V) vaping -----
they work just fine.

it is a safety protection mechanism,-- in the PCB .

 

[Kuya Dave]

hmm thats what I stated basically.
PCB
But my 510 901 401 801 808 all work at 6v on the indulgence hehe.
I must have got lucky with all this stuff.
901 at 6v I like. almost as much as my 401 at 3.7v lol