- Status
Move over Stealthy - a smaller guy is in town... well, just an unch.
Tera - aluminum case; 65mm x 32mm x 25mm; 1200mAh, 25C lipo
Stealthy - 69mm x 33mm x 22mm; 1200mAh, 25C lipo
WONDERFULL mod MAMU....might I ask for a link to the enclosure?
Neat and tidy.
Ive read that the e juice will eventually route its way through epoxy and hot glue on the puck mod site, he advises using a certain epoxy.
I am eventually wanting to make a mini mod such as the plastic 9v box mod but was unsure because of that. Your new box mod solved that fundamental read and non-ignore..
woot
I was at nivels site listened in on your radio interview cannot believe you do not hold a masters in electronics. Then you said software designer as its kissin cuzzin woot again, your mods and helpfuls are liquid Mamu... Slang for awesome, drink it up, I am...
Ive read that the e juice will eventually route its way through epoxy and hot glue on the puck mod site, he advises using a certain epoxy.
I am eventually wanting to make a mini mod such as the plastic 9v box mod but was unsure because of that. Your new box mod solved that fundamental read and non-ignore..
woot
I was at nivels site listened in on your radio interview cannot believe you do not hold a masters in electronics. Then you said software designer as its kissin cuzzin woot again, your mods and helpfuls are liquid Mamu... Slang for awesome, drink it up, I am...
The case is from that site that must not be mentioned - you know the one.
google AE-060-BE1 and it will come right up. I was going by memory on the size, it's actually 66mm x 30mm x 27mm.
Had to do some creative packing to get everything to fit with that shorter length and width. Also had to dremel off some of the PCB ridges inside the case.
THX..... found it .....The case is from that site that must not be mentioned - you know the one.
google AE-060-BE1 and it will come right up. I was going by memory on the size, it's actually 66mm x 30mm x 27mm.
Had to do some creative packing to get everything to fit with that shorter length and width. Also had to dremel off some of the PCB ridges inside the case.
Last edited:
It is possible to do a flush 510 connector for these mods? Would it fit so the atty looks flush with the top? Also wondering it its possible to see the inside of the blue aluminium one Mamu? Its an awesome looking mod.
Seriously I really need a Mamu DNA20
Get to building mate! With all of the information and support from the forum it is doable for most everyone.
Plus, you will have great satisfaction vaping on a mod that you built with your own hands. I haven't put mine down since I finished mine.
Get to building mate! With all of the information and support from the forum it is doable for most everyone.
Plus, you will have great satisfaction vaping on a mod that you built with your own hands. I haven't put mine down since I finished mine.
Yup, probably will try...but I still need one Mamu Dna20 for keepsake
Dam those stealth dna20s looks crazy nice!
Was wondering on the wires. Does the colour mean anything? Is it ok if i don't follow the milo colour build? And just use black and red for all the wires?
Also, i went to a few shops in my country. They don't seem to understand the 20/24 gauge measurements. How else can i pick the size if they don't know the size?
R these wires copper wiring inside?
sorry for noob questions. Working on my first build.
Was wondering on the wires. Does the colour mean anything? Is it ok if i don't follow the milo colour build? And just use black and red for all the wires?
Also, i went to a few shops in my country. They don't seem to understand the 20/24 gauge measurements. How else can i pick the size if they don't know the size?
R these wires copper wiring inside?
sorry for noob questions. Working on my first build.
Possible to see a picture of the inside to see how the atty connector fits inside? is everything dropped lower to fit it in?
Yep you can mount the atty connector flush without a drip well.....
The wire color is not important. It's just easier to see what goes where.
You should use copper wire.
You can google an American Wire Gauge conversion tool to find the metric equivalents to 20/24AWG.
It is a "tight fit" to get it all in there.....planning and test fitting is advisable.....sorry for the poor picture quality...and note that the fire button on the 20d must be removed in order for everything to fit.... in these pictures the carto in the tank sticks down below the tank, ya can slide the tank down to where the tank sets almost flat against the device case...
Last edited:
I have a question. I have built one VV mod from scratch before (nothing as nice as these)... I'm using only mechs right now, but am wondering how low of a resistance you can use for a coil on one of these bad boys? When does the circuit protection kick in? I just gotta figure out where to buy one now...
The specs on the DNA20d says minimum of 1 ohm.....ya can go just a tad lower but it doesn't regulate the wattage at a certain point , nor is it supposed to...IMO sub-ohm coils are not necessary when using regulated devices....
I realize this, but I'd like to stick as near 1 ohm as possible, as in my (fairly limited) experience with regulated mods, higher resistance + higher voltage does not = lower resistance with lower voltage.... Just wondering. Thanks for the info! Now I gotta FIND one...
As you get more experience you will realize that it's similar in most ways, and superior in some.
To answer your question you can go to .6 to .7 on the DNA20.
- Status
