Eleaf Lemo Drop. I want one!
- Thread starter Nuclear Cowboy
- Start date
- th_trl_thread_readers 0
- Status
Though that is an excellent idea...one that many would love to take advantage of...the chimney and take would most likely cost about as much as buying the whole tank!!!
How bout wrapping a coil for one of these? Looks like you need to bend the legs back to go thru post holes, if you know what I mean.
I'm experienced at wrapping coils, but for my RDA's for my Reos, and these look a little more tricky.
Would you get a good vape with a 1.2 -1.4Ω single coil? I would use this on an unregulated mech. device.
I'm experienced at wrapping coils, but for my RDA's for my Reos, and these look a little more tricky.
Would you get a good vape with a 1.2 -1.4Ω single coil? I would use this on an unregulated mech. device.
Last edited:
And a clone to boot
Half the clones are made at the same factory. And half the clones are better then original.
Ok, after watching a couple build videos I see you don't have to bend the wires like I thought. I like the look of these, and the apparently easy build. Now if I can just get over the fact that the Lemo is slightly bigger in dia. than my mods I can see getting one.
Mine came pre-built with a 1.0 coil and pre-wicked and it hits like a madman!
I'm afraid to rebuild it cuz it's working so good!
Hahahaha.....just order up about a dozen cases of them.....vape and toss!!!
I just got a Lemo drop yesterday and it really shines between 21 and 23 watts. I have a 1.12 ohm coil in it and it's too weak on a mech. I think you should build it to .8, maybe .9 at the highest or .7 at the lowest if you want a good strong lung hittin vape on a mech.
also I had no problems with going through the post holes. I just pre bent the leads and cut them to size. Kept the screwdriver in the coil while I positioned it and screwed down the screws. I just made sure to flip the coil over from how I build my Kayfun, so the leads are comin down from the top of the coil, not comin off the bottom. So it is more like an arch than a cursive "e" if the makes sense.
Last edited:
Yours came wicked already? That's odd, none that I've seen had the wick installed just the coil. Anyway, I'd never use a wick installed in a device I bought. Don't you wash your gear when you get it before vaping it?
Mine was precoiled and prewicked also and I ran the coil that came with it till a few days ago. I've found my sweet spot after a few builds at a 26g 6 wrap 3mm ID macro coil. The flavor and vapor is spot on at .9 ohms and 32.5 watts with my current juice. 
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Last edited:
When I rec'd mine all I had to do was add juice & vape. I haven't cleaned anything I've bought prior to using it.
Yes I usually clean them but I smelled this one real good and couldn't detect even the slightest hint of oil or anything and figured if they wicked it it must be clean and ready to go. When I vaped it I couldn't taste anything strange at all so I just kept going.
I've bought other tanks and could smell oil the second I took them out of the box but with this one nothing.
Back when I got some things from Fasttech this was also my thought. It came wicked- must be ready to go.
So, I'd add juice then immediately have my eyes pop out my head- the vape was so bad.
{IMO} It's ridiculous to send something pre-wicked that needs to be cleaned.
I no longer buy from Fasttech only cause I prefer immediate gratification & waiting forever + a day sucks.
Everything I've bought stateside I haven't cleaned prior to use.
- Status
