Maybe I am wrong, but Isn,t it the o ring wich keeps the button inside Esterigon?!
Esterigon official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
I'm chasing airplanes today. As soon as I'm back in Dallas Ill see what I've got. I think a small Delrin & an o-ring? Not sure right now.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Yes Stan but if you unscrew the pin from the button you can see this plastic piece that electraglide says.
This pin must be tighten enough on the button not to cause these issues.
(if it's not... it may cause a short circuit)
thx stelioss but the problem was not a short....
like i said- it is the o ring wich keeps the button inside Esterigon
...its not the plastic, its the o-ring. The o-ring keeps the button in place.
The plastic cant be worn, except you damage its threads by crossthreading button pin inside it
lool
Maybe this is something everyone already know, but figured I would mention it.
When screwing the tube, push it "up" (towards the button) while turning it. This will make the tube threading smoother since the spring is staying compressed and tube threads aren't grinding each other.
When screwing the tube, push it "up" (towards the button) while turning it. This will make the tube threading smoother since the spring is staying compressed and tube threads aren't grinding each other.
thats true zero. We have to screw the tubes while pushing them at the same time
electra, no worries, its not the plastic, its the o-ring. The o-ring keeps the button in place.
The plastic cant be worn, except you damage its threads by crossthreading button pin inside it
Just got back to town. Will take apart and clean it up and see what happens. I did take it apart and reassemble a few days ago and it wouldn't stay in. May need to get new O-ring.
Sent from my iPhone using Tapatalk
got my esterigon yesterday guys.
wonderful and awesome device as all the imeo's product.
I was wondering am i safe using my esterigon with a 0.25 ohm coil with my zenith? i'm afraid that it will be some problems expecially cause scott boner in his vid doesn't suggeto to go super low coil on it
wonderful and awesome device as all the imeo's product.
I was wondering am i safe using my esterigon with a 0.25 ohm coil with my zenith? i'm afraid that it will be some problems expecially cause scott boner in his vid doesn't suggeto to go super low coil on it
I dont know why Scott suggested something like this but you can use any ohm you like Lan
Those are quite fat and strong springs in esterigon, no way they will colapse at any known setup
Thanks imeo And Thanks zuTman. I'm gonna pump My Zenith with tris wonderfull art piece!
Those are quite fat and strong springs in esterigon, no way they will colapse at any known setup
Also they are very strong. So even with hand it's hard I don't think current will make it collapse at all.
Sorry... not so excited about my esterigons. At first very impressed about the design and performance, now disappointed about the button. A button only fixed by one o-ring ist not good for daily use outside home. Lost (and found ) the button three times. Okay, have my iAttys again sit on my GGTS's...
Gesendet von iPad mit Tapatalk
) the button three times. Okay, have my iAttys again sit on my GGTS's...Gesendet von iPad mit Tapatalk
Sorry... not so excited about my esterigons. At first very impressed about the design and performance, now disappointed about the button. A button only fixed by one o-ring ist not good for daily use outside home. Lost (and found
Gesendet von iPad mit Tapatalk
Do not be disappointed, maybe is just a matter of installing a thicker o-ring.
On my Esterigons, when installing the button, you have to press the button assembly until it feels that the o-ring has passed through, and to uninstall it, I have to pull hard the button assembly, I mean, is not that easy like it will come off by itself, or by carrying it in the pockets, but easy enough to take it off without using any tool, just the perfect balance.
blue, the button needs a lot of force to come out. What is happening is that o-ring is damaged because of the assembling from your seller or because of your assembling. Maybe you didnt put vaseline to your o-ring.
My o-ring is on my esterigon for 3 months and its more than ok. So keep the good impressions for your esterigon because its only a metter of assembling mistake
My o-ring is on my esterigon for 3 months and its more than ok. So keep the good impressions for your esterigon because its only a metter of assembling mistake
Sorry... not so excited about my esterigons. At first very impressed about the design and performance, now disappointed about the button. A button only fixed by one o-ring ist not good for daily use outside home. Lost (and found
Gesendet von iPad mit Tapatalk
Imeo, both esterigon's were not assembled by me and I took the button never out by myself. It just happend. Let's see, I ordered new o-rings by ESG. But I think, I prefer screwed buttons... Would be nice, if esterigon doesn't disappoint me; it's a wonderful combination with iAtty and - I hope soon - Tilemahos
Gesendet von iPad mit Tapatalk
Gesendet von iPad mit Tapatalk
esterigon is made after a lot of deep thoughts blue. I ensure you that you will not have any issues with it with your new o-rings. NO WAY!
- Status
