eVic-VT mini?

[pufZeppelin]

notice the ‘locking lug’

wish there was a corresponding one inside the cast cavity
that resides inside the body, but there is not…

seems just a ‘little’ more thinking would have made it close to foolproof…

 

[aldenf]

notice the ‘locking lug’

wish there was a corresponding one inside the cast cavity
that resides inside the body, but there is not…

seems just a ‘little’ more thinking would have made it close to foolproof…

View attachment 512391

View attachment 512392

Thanks, pufZeppelin! That makes me feel better. But, as you say, a little extra effort could have made it foolproof.

 

[Rayburn_]

have read the whole thread but any1 else have a lose 510 and tanks not sitting flush

Had that same issue with one of my subtanks, the other one sat fine oddly enough.... I used the black plastic circle that sits on the top of batteries and sat it around the 510.. Works perfect and has stuck in place for more than a month

 

[ariffza]

I just noticed that my 510 pin is also stuck inside the black plastic sleeve. Its is no longer a spring loaded pin anymore Tried to pry it out using one of my micro screw driver but wasn't successful. Did anyone experienced this problem able to fix this without disassembling the whole board?

 

[vincom]

Had that same issue with one of my subtanks, the other one sat fine oddly enough.... I used the black plastic circle that sits on the top of batteries and sat it around the 510.. Works perfect and has stuck in place for more than a month

cant tell by the pic but is it on top of the mod casing , exactly what plastic circle from the battery

 

[vincom]

notice the ‘locking lug’

wish there was a corresponding one inside the cast cavity
that resides inside the body, but there is not…

seems just a ‘little’ more thinking would have made it close to foolproof…

View attachment 512391

View attachment 512392

i have a fat daddy 510 i used to fix my mvp2, one day im going to see if i can mod it into the evic mini

 

[Rayburn_]

cant tell by the pic but is it on top of the mod casing , exactly what plastic circle from the battery

Yea it just stuck to the mod around the 510, the circle is from 18650/18350s and sits around the positive top... I used a old battery, just unpeel the wrapper and it is held on by a little glue..

 

[aldenf]

Has anyone had any success with SS yet? Grade, gauge, build? Thanks!

 

[louiesquared]

Has anyone had any success with SS yet? Grade, gauge, build? Thanks!

I am having great success with 0.25 Crown stock coils. 470-500 degrees at 60 watts. Nice warm dense vape that is very consistent.

 

[zeus01]

Sent from my AMOI N820 using Tapatalk

 

[vitorchapas]

Sent from my AMOI N820 using Tapatalk

Hmm... Used a hex editor?

 

[cindycated]

i have a fat daddy 510 i used to fix my mvp2, one day im going to see if i can mod it into the evic mini

That would be a neat thing to do - let us know if you get that to work. It's starting to sound like a janky 510 i some of the units might be the issue with this mod.

 

[vincom]

That would be a neat thing to do - let us know if you get that to work. It's starting to sound like a janky 510 i some of the units might be the issue with this mod.

well i took it apart, 1st problem is hole on top is too small for the fatdaddy so would need to widen it.
main problem is the lenght of fatdaddy is too long and will most likely hit the board but might be resolved by putting spacers between fatdaddy and mod body.
the metal cradle holding the 510 might be in the way.

 

[Diyguy]

Has anyone had any success with SS yet? Grade, gauge, build? Thanks!

I'm using SS 304 dual coils of 26ga wrapped on 2.5mm, at 0.28 ohms total. Resistance is holding and TC performing well, much better than Ti was for me.

 

[Jim_ MDP]

Hmm... Used a hex editor?

Was thinking the same thing... or Shooped

I'd keep the wire type in there though.
Yes... they cycle in the same order, but I'd have to keep checking.

 

[Tpat591]

well i took it apart, 1st problem is hole on top is too small for the fatdaddy so would need to widen it.
main problem is the lenght of fatdaddy is too long and will most likely hit the board but might be resolved by putting spacers between fatdaddy and mod body.
the metal cradle holding the 510 might be in the way.

FD V3 Shorty would probably be your only possibility there. Let us know how it goes. May solve a multitude of sins.

 

[vincom]

FD V3 Shorty would probably be your only possibility there. Let us know how it goes. May solve a multitude of sins.

for now it works fine my only prob is gap between atomizer and mod body and atomizer is able to slightly wobble, 510 is held in place by a metal cradle which would be almost unbreakable by the wobbling

 

[HDMontana]

I added a 510 heat sink right away, like I do on all my new mods. Protects the 510 threads on the unit. Works fine on the evic, as well as my other mods.

HD

 

[zeus01]

Hmm... Used a hex editor?

yup,,,
wasnt made by me thou

 

[ariffza]

After running on only SS TC since FW 2.0 update with great success, I decided to try Ni mode again, just to see whether FW 2.0 has made any improvement with regards to the weak vape issue. Although at first it vaped superbly, I'm sad to report that the problem is still not corrected (at least for me). What's worst now is in SS mode, it won't ask me whether I have a new coil or not when changing different SS coil build tanks. I'm not sure whether its because of the stucked 510 pin or because I tried using Ni mode, but this made me want to get another mod. I just want a mod that'll work with Ni and SS reliably everytime.