Before you go inside take some pics & screenshots to send to Erik over at Ecig.com. Not sure what he will do for you but Willy got a replacement pack because he reported his issue. Doubt they will give you a whole device without requiring the old one shipped back, but worth thinking about a conversation with him.
No I didn't put the white battery on the black dx200. At this point I think it's a board issue not a battery issue.
The black battery seems to be ok on the white mod. And if the board inside the dx200 is messed up I don't want to risk damaging the cells of a known good setup. I've used 1 of the white ones for a couple of days, I know it works fine. I bought 5 of these but only "used" 1 (the white one) I was just bored and playing around with the black one.
Now I think I need to use and check each of them.
To skip the taifun gt2 air. Yeah just now... I was supposed to jump on them when I found the airs in China.. Waited.. Now fasttech has them, and emailed focal, they are also getting them. By waiting for fasttech or focal the airs will be cheaper. Because they were about $20 ea + shipping ($35?) from China... So I was going to order several to balance out the shipping... Now I can order 1 or 2 at $22 free shipping.
Now, after getting the kf5 and not being as impressed as I thought I'd be, I'm trying to think about my purchases a little before jumping wallet first.
I may order anither squape x? Focal has one with the single coil deck for $34. It's a juice hog of a tank and its a little bit of a female dog to build on (duals anyway), but the vape is excellent and the air flow is Goldie locks. Not too tight, not too loose... Just right.
Yeah I was thinking that. As I said earlier. I have 5 of these in various colors, I had bought them for the vape apocalypse but now I think I need to open and test and use them all. To be safe.
No I didn't put the white battery on the black dx200. At this point I think it's a board issue not a battery issue.
The black battery seems to be ok on the white mod. And if the board inside the dx200 is messed up I don't want to risk damaging the cells of a known good setup. I've used 1 of the white ones for a couple of days, I know it works fine. I bought 5 of these but only "used" 1 (the white one) I was just bored and playing around with the black one.
Now I think I need to use and check each of them.
I really can't see how it would hurt the battery unless you left it hooked up, worse I've seen them do when the board has a problem is drain a battery below the cutoff. But anyway, you really should email ecig and let them know what it's doing. I went to my receipt email from the purchase and replied to it with my message.
I think you should use a meter and check the JST plug as well as the pack's main....or did you already?No I didn't put the white battery on the black dx200. At this point I think it's a board issue not a battery issue.
The black battery seems to be ok on the white mod. And if the board inside the dx200 is messed up I don't want to risk damaging the cells of a known good setup. I've used 1 of the white ones for a couple of days, I know it works fine. I bought 5 of these but only "used" 1 (the white one) I was just bored and playing around with the black one.
Now I think I need to use and check each of them.
I read some time ago about the pins in the battery's JST connector not making with the boards JST pins.
Well the plot thickens. After using each battery on each of the mods, the troubled black battery and mod have started charging and registering correctly. I'll use the black one tomorrow and see if it was just a glitch during firmware updating....?
I'll check them all over the next couple of days. I've still got 2 from the first round order that are sealed. So I definitely need to check them all after this little episode.
I'll check them all over the next couple of days. I've still got 2 from the first round order that are sealed. So I definitely need to check them all after this little episode.
Sounds like dirty connectors from storage that just needed a little use break-in to improve the connection? Happy it wasn't more serious.
+1 for the Square X Dream
It does have a little more Air Flow than the V5 I'v been pondering a second one my self, Still just a little worried about coating failure.
Mine has worked flawless for over a month now
this is an atty that should be in everyones collection I'v been running mine with a single coil with out the adapter & it's N/P.
IMO that adapter will block half the air flow & it will be a tighter draw than a V5.
Just speculation on my part
The SJMY clone on 3F is excellent
& it's not just me who thinks so, look at the reviews all positive 
I'm kinda interested in the new VT75 Nano.
$99.00 Authentic HCigar VT75 Nano 75W TC VW APV Mod - 1-75W / 100-300C'(200-600F') /1*18650 / zinc alloy at FastTech - Worldwide Free Shipping
$99.00 Authentic HCigar VT75 Nano 75W TC VW APV Mod - 1-75W / 100-300C'(200-600F') /1*18650 / zinc alloy at FastTech - Worldwide Free Shipping
And the pistol grip horn isn't half as bad as I thought it would be.SDNA75 next to an Evolv reference mod. Small.
Ok...question two...all of my 18650s are crap/old...any suggestions for a great battery? Bride is reluctant as she is accustomed to power, though in a large size.
She has been asking for a more pocket friendly mod and I am trying to get her to use this one.
Thinking of these:
MODS BATTERIES & CHARGERS - Sony VTC5 18650 Battery - Vape Super Saver
or
4 LG 18650 HE2 2500mAh Li-Ion 35A High Drain Rechargeable Battery LGDBHE218650
She has been asking for a more pocket friendly mod and I am trying to get her to use this one.
Thinking of these:
MODS BATTERIES & CHARGERS - Sony VTC5 18650 Battery - Vape Super Saver
or
4 LG 18650 HE2 2500mAh Li-Ion 35A High Drain Rechargeable Battery LGDBHE218650
Last edited:
Similar threads
- Locked
