My nickel build. Dual twisted 30g, 9 spaced wraps, 3mm ID came out to .16Ω after settling. Currently vaping at 28w set to 500F.
Flash-e-Vapor V2 rba by Artur Schwarze
- Thread starter dice57
- Start date
- th_trl_thread_readers 0
- Status
This cotton feeder wicks are keeping up fine at 28watts?My nickel build. Dual twisted 30g, 9 spaced wraps, 3mm ID came out to .16Ω after settling. Currently vaping at 28w set to 500F.
Looks great btw, I'm so excited I'll finally have my v3 in a day or two, eeeep
I sent an email to Artur regarding shipping costs and speed through the Contact Form on the website. I encourage others to do the same.
I was very polite and complimentary of his product and offered examples of other EU vendor's shipping prices and speed and made suggestions in a helpful and caring tone.
I was very polite and complimentary of his product and offered examples of other EU vendor's shipping prices and speed and made suggestions in a helpful and caring tone.
I hope you have better luck than I did. I emailed him several times about a cheaper option for shipping but he never replied. Maybe if you wrote in German?
Got a reply a few hours later. Nothing long but said he will try to get better shipping options.
Yup, keeps up just fine. There's a little popping going on but it is a nice warm flavorful vape. You're going to love it.
It arrived!!! Woohoo!!!
The v3 is here!!!
Just gotta clean everything off (got long and short airflow tubes, long tank, 1.6mm air screw, steel center, markalon FeV v3, and repair kit). Oh goodness, pretty stoked right now!!!
The v3 is here!!!
Just gotta clean everything off (got long and short airflow tubes, long tank, 1.6mm air screw, steel center, markalon FeV v3, and repair kit). Oh goodness, pretty stoked right now!!!
Jax, not too long ago, many were using mesh straws to feed. How does the cotton cord compare to mesh?
I don't think he's used mesh feeder wicks yet, the mesh strips from Artur were too small to use.
Hey dems, you got all three sizes of FEV tanks! I'm still not sure whether you need the short top cap along with the "chopped" chimney for the nano setup. Hopefully not
Here's how I trimmed my wicks- just two small pads of rayon over the screws with nothing dangling down to the deck. Seems a long wick siphoned juice from the coil. Have fun with your new flashi! btw I saw you cruising around the ubertoot thread in the uk forum.
Haha, thanks!!! You damn straight I'm in the UTA thread, I'm going to snag one of those puppies come hell or high water!!!Hey dems, you got all three sizes of FEV tanks! I'm still not sure whether you need the short top cap along with the "chopped" chimney for the nano setup. Hopefully not
View attachment 421965
What lengths are your mesh feeders? Size jig? I can't roll sedge's recommended length tight enoughHey dems, you got all three sizes of FEV tanks! I'm still not sure whether you need the short top cap along with the "chopped" chimney for the nano setup. Hopefully not
View attachment 421965
I roll the mesh on a pin or wire about 1mm diameter. Use enough mesh to go around the pin about two and a half times, and roll in one direction (not back and forth). The mesh straw is initially 9-10 mm long. After I drop the straw down the feed hole, it will slide freely until it hits the rayon pad. Then I chop the straw at the top. Depending how fat the rayon pad is, my straw ends up about 8mm long.
Last edited:
No, only about 25 mm wide. I just measured. And it goes 2-3 times around the pin. If the straw is too narrow, you can unroll it a bit.
Sorry, dems I'm giving you the wrong measurements. Guess it depends on how fine the mesh is. I'm using 350 and 400 mesh. You have to play with it until the straw is just tight enough in the hole that it doesn't fall out when you go to screw the base onto the tank.
Last edited:
Ok thanks, I got no idea how I'm going to roll 110 60mm tight enough, sedge is a magician
Yeah that 110 mesh is pretty coarse. Maybe sedge torched it to take out the springyness.
No torching. I believe that once you get it started it's easy. You just got to get that first roll around the drill bit nice and tight
- Status
