Come to think about it: "pushing the wick out of the juice channels" is a good thing in my book because I don't want any of the wick in my juice channels at all
Fogger V4!!
- Thread starter Shofixti
- Start date
- th_trl_thread_readers 0
- Status
Come to think about it: "pushing the wick out of the juice channels" is a good thing in my book because I don't want any of the wick in my juice channels at all
Just an FYI, eciggity have a pre-order for the 26650 fogger, I ordered one in SS, hope it's as good as the V4.33498+++ Rev 8374 ∞ I have right now.
Not a single drop so far. I've been using it for a week now.
I've built my brothers V4.3 the same way and he is very happy too.
@AMDTrucking is there anyway I could pay you to mod my Foggers with fill screws like yours. 
Because those coils were so small I suspect the wicks were too thin to cope. I've just redone it with 2.00mm mandrel, 28 gauge wire, 0.7 ohms (was aiming for 0.8!) and used noncompressed, gently rolled cotton. I tried the chimney method of wicking - fluffed them up, trimmed to the top of the chimney, and gently pushed down in the area of the channels. If this doesn't work, I'll rewick using the conventional method.
When I removed the previous wicks they were burned.
I love the idea of top fill screws, but that's beyond me LOL
I've used 2mm silica with just a mm or two stuck down in the channels on horizontal coils and vertical coils with cotton packed around the base lightly and over the channels but not in the channels - both types of builds with no leaks. The only time it has leaked or flooded is when either silica or cotton wasn't sealing the juice channels in some manner. be sure to wet your build and push around the cotton before screwing the chamber on. I don't see anything that you have missed. But I am running 100% VG.
Could someone provide me with a link in the US where I can buy a none clone fogger v4? thank you guys.
@AMDTrucking is there anyway I could pay you to mod my Foggers with fill screws like yours.
I'll gladly drill yours for you. email me: amdtrucking@gmail.com I'm in Perris, CA 92570
Vapology.com? None on the website. Who makes them anyways? So annoying with all these stupid clones nowadays. A new customer doesn't even know way is what.
The Fogger is NOT a clone of anything else. It is an official product of Chinese company called: Yi Loong.
And, as far as I know - it has not been cloned yet and I don't think it will.
http://www.yiloong.com
Last edited:
So wait a minute! I thought the v4 is the newsest fogger on the market but now I see 4.3 and the like? Which one is the newsest and best performing?
There are several versions of the newest version 4. The latest is version 4.3 - which I have. Not necessarily the best.
So I've vaped another tank of DIY 50/50 juice with my new setup. I'm still getting small leaks out of the airholes, but I don't think the wicks are burning anymore.
It seems whenever I adjust the afc it leaks also - may be my imagination. But it's useless - I'm either going to take it off or just leave it wide open. I tend to chain vape, and the drip tip gets incredibly hot anyway!
I really want to get it leakproof...guess it's time to try a different wicking setup now. I always use cotton nowadays - but I do have some 2mm ekowool I think.
It seems whenever I adjust the afc it leaks also - may be my imagination. But it's useless - I'm either going to take it off or just leave it wide open. I tend to chain vape, and the drip tip gets incredibly hot anyway!
I really want to get it leakproof...guess it's time to try a different wicking setup now. I always use cotton nowadays - but I do have some 2mm ekowool I think.
Yeaaaah I spoke waaaaaay too soon.
Left my foggers on the side table over night and woke up to a mess.
Def need I squish some cotton in the vertical channel, if only just a bit. Sigh
Burping out loud using Tapatalk
Left my foggers on the side table over night and woke up to a mess.
Def need I squish some cotton in the vertical channel, if only just a bit. Sigh
Burping out loud using Tapatalk
Fogger v4.1. I either get dry hits or leaking with most juices. Think I will play with it a little more then try a Taifun GT clone. If that doesn't work, I guess I'm buying some drippers.
Here ya go, the guy I was referring to was the sellers name on eBay, but he is out of them, this is a link to one other seller good price free shipping. The 4.whatever is just referring to the newest version of the same thing, they have made a few changes but not a huge deal, this link is the newest version, it's got a bigger deck and holds less juice but it vapes the same and there's no way to get the older versions besides www.vaporbeast. Com
I bought the 4.2 version there a couple days ago but it was around $45, I paid extra for the maybe 2ml extra capacity.
If you want the newest version here's a link to the eBay page
http://www.ebay.com/itm/Latest-Vers...t=LH_DefaultDomain_0&var=&hash=item4ad5746401
- Status
Similar threads
- Locked
