Fogger V4!!
- Thread starter Shofixti
- Start date
- th_trl_thread_readers 0
- Status
I've got the other side of the coin. I have two TGT's, one I modified and the other not. I want to give it some time to see if I run into some kind of problem in the future. If not - I'm modifying the other one too.
I'm also going to modify my Big Fogger, when it arrives. And my Kayfuns 3.1 as well as AGA-T7 that already has a Top Fill Hole, but only one. I'm adding the other one to it.
P. S: What I like about this modification is not only it is easy and convenient to fill, and it takes more juice. But it is also safer. You see, when you close the Air Intake and the Drip Tip holes, the chamber retains air in it that prevents an e-liquid from entering the chamber no matter what pressure you apply when filling.
That's a huge benefit in Fogger's case and Taifun GT I did it for the extra 2.5 ML
Last edited:
Interesting question...
Everyone runs two parallel coils on Fogger V4+.
Do you mean, more then dual coil?
I guess it is possible, the deck is big enough to do it. I just don't see a reason for it.
Everyone runs two parallel coils on Fogger V4+.
Do you mean, more then dual coil?
I guess it is possible, the deck is big enough to do it. I just don't see a reason for it.
Last edited:
No, sorry I meant 2 wires on each coil, like twisted only, not twisted, parallel, running together.
Sent from my Transformer TF101 using Tapatalk
Sent from my Transformer TF101 using Tapatalk
All the drippers like them, possibly more than twisted wire which is my personal favorite as of current...
Sent from my Transformer TF101 using Tapatalk
Sent from my Transformer TF101 using Tapatalk
Refresh, this is what I was talking about.
Oh, I see.
But it is almost the same as using thicker wire. Like using 22 Gauge instead of 28.
I, personally would hesitate to use anything thicker then 28 Gauge in dual configuration on a Tank. Dripper - Oh yea. Besides, my Fogger V4.3 with dual 28 Gauge 2.5 mm Coils at 0.5 Ohms is producing very satisfying large amount of vapor and flavor that I don't want to go higher. I mean lower resistance that is. For all seriousness, this Fogger V4.3 is on par with my Genesis type tanks and almost as good as my Drippers. Why change it? I feel sorry for my four Kayfuns, two Taifuns GT, Aqua, Ithaka and Flash E-Vapor, they get neglected now. I'm awaiting on AGA-T7 and Big Fogger 10 ML now.
P.S: I will use Flat Ribbon Kanthal on my Foggers, I've used it on the rest of my tanks and it improves their performance a lot. I even built a special Kayfun for my brother to be used on his 11 Watt EVIC using the flat ribbon 0.5 mm and it's performing quite well for a low power crappy mod like EVIC
P.P.S: Nice looking tight micro coil though. I like when people take pride in what they do. Keep up the good work!
Last edited:
I may have spoken too soon about the Squape "working right." It's got a slow, constant leak out of the 510. I didn't realize it was even there because the vape itself was pretty great; no dry hits, no gurgling. And I'm a chain vaper. Then, when I went to take the 26650 battery out to show someone, I saw a sheen of e-liquid all over the top cap. Didn't get down past the cap though, battery and tube were both bone dry.
But something is seriously going on with this Squape. It is a clone of uncertain providence, being that this one came from angelcigs.com. Could be that I just have the coil sitting too low in the channel. I'll work on it some tomorrow and try to remember to take photos of my various attempts a fixing the issue.
I should add, btw, that your advice on the current V4 Fogger has REALLY helped me out. I went back and tweaked the coils so they are more uniform and nudged them back into place directly over the air holes. Short, fairly dense wick, with just a bit laying on the deck and sneaking up towards the channels, but NOT shoved INTO said channels.
The result is hit after saturated hit.
But something is seriously going on with this Squape. It is a clone of uncertain providence, being that this one came from angelcigs.com. Could be that I just have the coil sitting too low in the channel. I'll work on it some tomorrow and try to remember to take photos of my various attempts a fixing the issue.
I should add, btw, that your advice on the current V4 Fogger has REALLY helped me out. I went back and tweaked the coils so they are more uniform and nudged them back into place directly over the air holes. Short, fairly dense wick, with just a bit laying on the deck and sneaking up towards the channels, but NOT shoved INTO said channels.
The result is hit after saturated hit.
I may have spoken too soon about the Squape "working right." It's got a slow, constant leak out of the 510. I didn't realize it was even there because the vape itself was pretty great; no dry hits, no gurgling. And I'm a chain vaper. Then, when I went to take the 26650 battery out to show someone, I saw a sheen of e-liquid all over the top cap. Didn't get down past the cap though, battery and tube were both bone dry.
But something is seriously going on with this Squape. It is a clone of uncertain providence, being that this one came from angelcigs.com. Could be that I just have the coil sitting too low in the channel. I'll work on it some tomorrow and try to remember to take photos of my various attempts a fixing the issue.
I should add, btw, that your advice on the current V4 Fogger has REALLY helped me out. I went back and tweaked the coils so they are more uniform and nudged them back into place directly over the air holes. Short, fairly dense wick, with just a bit laying on the deck and sneaking up towards the channels, but NOT shoved INTO said channels.
The result is hit after saturated hit.
I am very happy I could be of any help.
Fcuk! Just broke my tank anyone know where to buy replacement glass?
Sent from my Transformer TF101 using Tapatalk
Sent from my Transformer TF101 using Tapatalk
Vapercompany.Com $7 shipped out of LA, CA. Oh yeah!
Sent from my Transformer TF101 using Tapatalk
Sent from my Transformer TF101 using Tapatalk
You are not going to believe this people, but as I was machining my Taifun GT modification, I had my 26650 Stingray with Fogger V4.3 standing on my work bench. My wife went by like a hurricane and knocked it down. It fell down on a solid concrete floor from 4 feet high and NOTHING had happened to it. Nothing at all! Not even a scratch! I think I should go buy me a Lottery ticked because my luck has obviously changed for better
Well, thanks to Tbev for the rayon hint- IT WORKS - no more dry hits, no more leaking - this stuff is amazing
Forgive me please, but I am totally unfamiliar with this wicking material.
Could you tell me more?
Thanks.
Mike.
Oh yes - you need some! (I can send you some actually, since I have 500 ft). It's rayon from Sally's Beauty Supply. There's a whole long thread here which I spent last night reading:
http://www.e-cigarette-forum.com/fo...ck-better-flow-flavor-saturation-nic-hit.html
http://www.e-cigarette-forum.com/fo...ck-better-flow-flavor-saturation-nic-hit.html
Probably, as long as it's 100% rayon. But those are really expensive, compared to the Sally's stuff! I'm in the SF Valley - where are you?
Forgot to add, apparently it's the same stuff that is in the top of medicine bottles!
- Status
Similar threads
- Locked
