Scubabatdan - With all your experience regarding attys, etc., is there are particular method (with video) that you prefer for preparing mesh? Applogy offered if you have already spoken to this.
- Status
Nope,big DiD thread on the french forum,they have their own specialists there too you know
Leave to the French to discover an antigravity device.Nope,big DiD thread on the french forum,they have their own specialists there too you know
OK bj, got a question for ya, lol? I got a vivi from a freind, I increased the hole next to the Ground screw and it keeps popping the top section of the wire almost imediately when I fire it? Got a 4 round, a 5 round and a 6 round and it poppes it everytime?
Sounds like a direct short. Did you take a ohms reading? When starting a new coil/wick set the voltage down as low as you can until you are sure there are no shorts.
Was on a EGO-T 18650 mod at 3.4V. When I touched the ends the reading would jump around, but the first reading was 2.0 ohms. Now it quit working all together, lol.
WORD OF WARNING TO MODDERS. THERES A WIRE THATS SOLDERED TO THE SILVER SPACER IN THE MIDDLE OF THIS THING. WHEN TIGHTENING THE MIDDLES SCREW MAKE SURE YOU HAVE A PAIR OF NEEDLE NOSE PLIERS ON THE SPACER. It has a wire between the middle spacer and the pos connection on the bottom of the base. Turn it too many times and it will break. Here's the peices
Theres NOTHING to hold it tight on the top were it goes thru.
WORD OF WARNING TO MODDERS. THERES A WIRE THATS SOLDERED TO THE SILVER SPACER IN THE MIDDLE OF THIS THING. WHEN TIGHTENING THE MIDDLES SCREW MAKE SURE YOU HAVE A PAIR OF NEEDLE NOSE PLIERS ON THE SPACER. It has a wire between the middle spacer and the pos connection on the bottom of the base. Turn it too many times and it will break. Here's the peices
Theres NOTHING to hold it tight on the top were it goes thru.
Last edited:
Here is a video on my channel for the GTUS, the only differance is you will not need to do the 1/8" fold for the bottom, everythng else is the same
Dan
I haven't noticed (not a surprise ) any holding capacity listed for these. How many mLs do they hold? 
) any holding capacity listed for these. How many mLs do they hold?
I haven't noticed (not a surprise
About 2 mls I think!
Really? Only 2mLs, hmmm. About the same as a XL CE2? Dang, was hoping for like something like 3 or 4 at least.
ETA:
OK, did find this at Mountain Oak Vapors listing:
"The Smoktech ViVi Rebuildable Tank is the newest tank setup from Smoktech. This tank is made from polypropylene and holds approximately 4ml. These are threaded with a 510 connection for use on most Ego-style batteries, and other APV's with the 510 connection. End caps are all metal, and the mouthpiece is designed after the popular Ming style. The setup comes wicking and coil already installed. You can replace the wick, and heating coil very easily on these using nichrome or kanthal wire and wick. "
ETA:
OK, did find this at Mountain Oak Vapors listing:
"The Smoktech ViVi Rebuildable Tank is the newest tank setup from Smoktech. This tank is made from polypropylene and holds approximately 4ml. These are threaded with a 510 connection for use on most Ego-style batteries, and other APV's with the 510 connection. End caps are all metal, and the mouthpiece is designed after the popular Ming style. The setup comes wicking and coil already installed. You can replace the wick, and heating coil very easily on these using nichrome or kanthal wire and wick. "
Last edited:
I have seen them advertised as like 5, but I am guessing it is closer to 3. Next time I fill it I will measure if someone else hasn't by then.
EDIT:I am going to say 2.5ml maybe. I just sucked it out and it came to the 2ml graduation, and it was not quite full.
EDIT:I am going to say 2.5ml maybe. I just sucked it out and it came to the 2ml graduation, and it was not quite full.
Last edited:
Thanks for the responses . Mine are finally on their way from China (there was a holdup with another item in the co-op). I was hoping to get at least most of a day's vaping on one fill, and looks like that may be possible. (Although, for some unknown reason, I'm half-way through my second fill of my cotton-wicked XL CE2 now 
)
. Mine are finally on their way from China (there was a holdup with another item in the co-op). I was hoping to get at least most of a day's vaping on one fill, and looks like that may be possible. (Although, for some unknown reason, I'm half-way through my second fill of my cotton-wicked XL CE2 now )
I can get close to 6 hours out of it. Cotton has been working well in it as well.
Hope they don't take too gosh awful long to get to you TC!
Hope they don't take too gosh awful long to get to you TC!
Should have them in-hand early next week. Already got the TBC-2 ('Phoenix-style') RBA (dripper) a week or so ago. But I'm a 'distracted vaper' , already burnt a cotton wick in that by vaping it dry 
, already burnt a cotton wick in that by vaping it dry 
I found that out the hard way. Replaced the wire, but my gloppy solder job was so sloppy I kept shorting it out. Tried to insulate with silicone, and didn't let it cure long enough. Needless to say, silicone fumes are indeed a little flammable.
Well I re soldered it back together but it's still shorting out. I can see that neither post is touching it from the top, but can't figure it out????????????????????
- Status
Similar threads
- Locked
