G-Tank-US-CO-OP Support Thread

[asdaq]

bp, with that pic I can't imagine you are getting dry hits, is your wick reaching to the bottom of the chamber to soak up that excess?

With the gurgle, it seems that it could be your airholes are siphoning liquid from the wick as there is a convenient surface for the juice to travel along but it is hard to tell. There needs to be a gap between the wick and the airholes. A longer piece of that tubing might block the holes, but a shorter piece would not. Or the piece you have isn't stuck in all the way???

 

[bp400]

bp, with that pic I can't imagine you are getting dry hits, is your wick reaching to the bottom of the chamber to soak up that excess?

With the gurgle, it seems that it could be your airholes are siphoning liquid from the wick as there is a convenient surface for the juice to travel along but it is hard to tell. There needs to be a gap between the wick and the airholes. A longer piece of that tubing might block the holes, but a shorter piece would not. Or the piece you have isn't stuck in all the way???

Not sure I understand the bottom of the chamber question, the wick hits the bottom at the coil area.

 

[Murdock Ruml]

My guess is your wick is two loose and flooding while not in use. My guess for the dry hits is that the coil an wick needs to be broken in. I also had both of those problems. The harshness went away after a couple of days.

 

[fender0942]

Yea. I use to get that problem too. Wick is too loose. Use something thicker to roll it. Or cut your mesh a little wider. Sometimes you can fiddle with what's there and get it to stop.

 

[davedrumdude]

Hey Dan any ETA update available?

 

[Killjoy1]

Parts just arrived on Thursday at emachineshop: http://www.e-cigarette-forum.com/fo...-us-co-op-support-thread-216.html#post5133886
Probably be at least a couple more days before there can be any updates beyond that ;-)


Dan, I love the "Ghost Protocol" GTUS setup. I may have to give that a try at some point after I've played around enough to get the hang of using it

 

[pseudus]

I got a little bit of work done on the G-tank-US site. Most of it on the FAQ, check it out here. I'm also trying to post interesting stuff that happens in the Support thread, like the Ghost mods we're seeing.

More feedback please... What do you guys think? Suggestions? Ideas? Complaints? Please put in your

 

[Mudflap]

I got a little bit of work done on the G-Tank-US site. Most of it on the FAQ, check it out here. I'm also trying to post interesting stuff that happens in the Support thread, like the Ghost mods we're seeing.

More feedback please... What do you guys think? Suggestions? Ideas? Complaints? Please put in your

All I can say is that the total package is extremely well done and will be an invaluable resource for me when I finally receive my G-Tank-US. Thank you, sir.

 

[Youssefa]

These things are easy.... but NOT always pretty. Dan just makes it look pretty

Hey Dan, What size polycarb tube for the tank?

 

[Scubabatdan]

These things are easy.... but NOT always pretty. Dan just makes it look pretty

Hey Dan, What size polycarb tube for the tank?

It was a 5/8ID x 3/4OD that I heated and shrunk the ID slightly with a heat gun so it will accept threading.
I have another method I am going to test to see if I can make an eaiser process anyone can do.
Dan

 

[Youssefa]

what size is the tank tube it doesn't look like a syringe

spoken from Inspire 4g

 

[Scubabatdan]

what size is the tank tube it doesn't look like a syringe

spoken from Inspire 4g

The tank is a syringe, it is the ideal instruments 6ml syringe. I just cleaned off the markings. Sorry, missed the work tank in the first question
Dan

 

[Extol]

i been out of the loop for the weekend. Dan are you thinking about ordering 100 tubes?

 

[Scubabatdan]

i been out of the loop for the weekend. Dan are you thinking about ordering 100 tubes?

Atually the hard to get 5/8 x 8.7mm x 3/8 poly end cap for the mouth piece for the ghost mod. Just working on getting a quote to have them made.
Dan

 

[bstedh]

Need a close button on the pictures. When you click on them you can scroll back and forth through them but no way to close back to the web page.

I got a little bit of work done on the G-Tank-US site. Most of it on the FAQ, check it out here. I'm also trying to post interesting stuff that happens in the Support thread, like the Ghost mods we're seeing.

More feedback please... What do you guys think? Suggestions? Ideas? Complaints? Please put in your

 

[Shead]

Ok after crusing the thread again I want the ghost top caps XD that looks sick

 

[bstedh]

I think I will try those brake honers on the covers. Those threads going all the way up cause a lot of premature condensation.....

I think that may be the biggest cause of my taste issues. Once the condensation starts it multiplies on itself cooling the vape even more.

 

[bp400]

Need a close button on the pictures. When you click on them you can scroll back and forth through them but no way to close back to the web page.

I noticed that too, but I clicked where the close "x" normally is in the upper right hand corner and it closed. Still kinda awkward tho and that was before the latest update I think.
ETA: just tried it, still works

 

[pseudus]

Need a close button on the pictures. When you click on them you can scroll back and forth through them but no way to close back to the web page.

Just click the picture again...

I noticed that too, but I clicked where the close "x" normally is in the upper right hand corner and it closed. Still kinda awkward tho and that was before the latest update I think.
ETA: just tried it, still works

Anywhere on the picture....

 

[BJ43]

Best place to buy the B tanks with silicone caps?