Mine gets used a couple times a week with a Rogue or maybe a Cyclone. It will never replace my Reos. I really do like that the logo has been moved.
Most likely from Catfish. I think he still has some in stock, or more on the way........^^^^^^^^^^^^still would like to know where you got your BF Rogue
I have had the same 5x lock, and I believe it has something to do with a short in the atty. the included RDA center post may be loose and needs tightened. My center pin was crooked as well, so when I installed the rda down, it would cause the loose center pin to contact the 510 threading. Tightening the center pin removed that issue for me.I’ve had mine for a few days and so far it’s not bad at all. For the price paid (about $60 – got it at Eciggity when they had their 25% off sale) I’m satisfied. Got it in blue and the fit and finish is decent. Couple of small blips in the finish but you have to look hard to spot them. Screen is centered; logo is just on the bottom.
The only real problem I’ve had is that it has gone into lock mode on its own on two occasions. It goes to sleep and, when I go to fire it, it displays the “click 5x to unlock” message. Clicking it 5x didn’t unlock it, but removing the battery cleared the problem. The two times it happened were on my first day with it. It has not re-appeared since, and I’ve run 3+ full bottles through it. Getting used to the fire delay on wake-up, but it’s still irritating.
I’m enjoying sqonking again! I had a Reo, but sold it about a year or so ago. I just may have to pick up a newer model Reo – the one I had dated back before they had the LP version.
^^^^^^^^^^^^still would like to know where you got your BF Rogue
Angelcigs is sending me a Geyscano to review. From skimming this thread it looks like some of the issues to look out for are the delayed fire from sleep and various board issues. Anything else I should pay close attention to when reviewing it?
I've used mine for a month and really like it. The feeding system works great, tube and connector nozzle has a big enough ID to let even thicker liquids flow easily with little resistance and it hasn't leaked a drop. Corners, especially the front four are pointy due to the door channel, could have been knocked down a bit but it is what it is.
It's been solid and other than the annoying delay coming out of sleep mode I think they did a decent job for the price point. I would have preferred air channels on the connector as I've got some M6 and A7 attys I use for bottom feeding but more and more connectors are coming out without air channels since most rbas and tanks have their own airflow. I even like the atty it came with now that I've got past the awkward design.
QC and the Delay are probably the biggest issues but what can be expected of China QC. Mine had some slight blemishes in the finish and came covered in some kind of slippery oily substance that took forever to get rid of.
Angelcigs is sending me a Geyscano to review. From skimming this thread it looks like some of the issues to look out for are the delayed fire from sleep and various board issues. Anything else I should pay close attention to when reviewing it?
Mine is black and has logo on the bottom. The chip is only 10 amps, I believe, and seems to be underpowered. Lots of folks complaining about battery life. It may be because the chip can't handle battery sag, but I'm no expert. The QC on the ridges that hold the door in place, they are very sharp in the corners.
It definitely does not have the power it should. The Hana clone was the same way. The Hana clone also required an extra click to wake up. Coincidence?Excellent info, thanks. I'll definitely be running it through the gauntlet. We'll see how much power it's really making. The 10A output limit is kind of a drag. It's advertised as being able to fire down to 0.2ohm but that will far exceed the board's amp output limit at 50W. 0.5ohm is the low threshold to stay under the 10A limit at 50W. Maybe I've missed it in this thread... are the board's specs known? I can't find any detailed specs, even on Yiloong's site.
Depending on max output voltage, the ideal build will probably fall somewhere around 0.8ohm to 1.0ohm when running max power.
Excellent info, thanks. I'll definitely be running it through the gauntlet. We'll see how much power it's really making. The 10A output limit is kind of a drag. It's advertised as being able to fire down to 0.2ohm but that will far exceed the board's amp output limit at 50W. 0.5ohm is the low threshold to stay under the 10A limit at 50W. Maybe I've missed it in this thread... are the board's specs known? I can't find any detailed specs, even on Yiloong's site.
Depending on max output voltage, the ideal build will probably fall somewhere around 0.8ohm to 1.0ohm when running max power.