Okay. Thanks. As long as it holds liquid, I don't really care.
Thats what im saying this drippin and then the dripping thru the crack sucks
- Status
Thats what im saying this drippin and then the dripping thru the crack sucks
Works for me, I would just make sure my jet is on its lowest setting, just in case....
You have a cracked tank? Or is your tank leaking around the o-rings?
that's no fun.....I take a lot of long hard drags off my zenesi 
To all of you "whistlers"...it's not beer in that tank....so don't try to suck the guts out of it!
Nice easy smooth drags is all it takes. Too hard of a pull can actually pull too much air across the coil over cooling it, which will reduce the vapor because the coil isn't being allowed to get hot enough to burn the juice.
yep....i used scotchbrite pads, made a 'v' outta it, put the tip 0-ring section in the V and twisted the hell out of it for a few seconds, checked the fit, and it worked.... some may take longer, as the siam mods driptips arent the greatest when tolerance is concerned
I really love my 30min drive to and from work now that I have my zenesis. Nothing better then chain vaping my standard to the point the vapor rolls out of the car when I get where I am going. Got a couple weird looks from the gate guard when I rolled my window down. A huge cloud rolled out the window, I see him take a few sniffs to see if he smells anything illegal. Seeing the puzzled look on his face when he smells licorice as he says " thank you, have a nice day!" is priceless.
Last edited:
Ill get to play in the boat with yall tomorrow.. Tracking says Zene at post office right now.. wish the post office stayed open later i would have picked it up today.. yay
Yes, use a torch. Start with butane. Propane and map work great but until you know exactly what you are doing, I would stay away from those because the get alot hotter than butane and you can overdo things with those
Remember...oxidize, not melt
chip eventually became a crack :/
dont really want 6' of it but i may have to order some nobody within 30 miles has anything I drove all over the other day
dont really want 6' of it but i may have to order some nobody within 30 miles has anything I drove all over the other day
@ ob - The correct tubing is 5/8 ID X 3/4 OD. I had to change mine out a long time ago and that is the correct size for the Zenesis. I was lucky enough to have som laying around (leftover from a previous modding project
I just figured that out the hard way today!
@ ob - The correct tubing is 5/8 ID X 3/4 OD. I had to change mine out a long time ago and that is the correct size for the Zenesis. I was lucky enough to have som laying around (leftover from a previous modding project
I just figured that out the hard way today!
Sorry, been away for most of the day, been very busy and didn't notice people wondering what the right size was for poly tubing to replace tanks with.
I see it says your in FL. Do you live down south? If so, you have any more tubing?
Sorry, been away for most of the day, been very busy and didn't notice people wondering what the right size was for poly tubing to replace tanks with.
I am about to ask one of those annoying questions that I am sure has been answered, but
I have a standard with a new button and am using a aw IMR 2000. Is it supposed to rattle around in there?
I have a standard with a new button and am using a aw IMR 2000. Is it supposed to rattle around in there?
well I did it again. broke a device.
I snapped a coil somehow.
I tried to get the wick out but it was really stuck. It broke inside. Now the plastic thing that the wick goes in is all messed up.
zen PM coming. Did not really even get to use it all that much.
I snapped a coil somehow.
I tried to get the wick out but it was really stuck. It broke inside. Now the plastic thing that the wick goes in is all messed up.
zen PM coming. Did not really even get to use it all that much.
Those of us still stuck here in the ding toolies want updates about vape bash and all of the cool things you are going to see!!
Good thing Zen got the vape lounge all set up before he takes off.
Get a good rest have a beer for me and thanks for getting the shirts made and shipped in such short order! Don't stay locked in your hotel room with your zenesis all weekend!! Most of all have fun!!
And make sure to put in a good word for me as a reviewer. I need things to review. LOL!
The correct tubing size is 3/4 ID and 7/8 0D
I hate tap plastics, by the way... For you... Tanks are a buck a pop... For me... 4.35 ea and six weeks lead time...
I hate tap plastics, by the way... For you... Tanks are a buck a pop... For me... 4.35 ea and six weeks lead time...
- Status
Similar threads
- Locked
