Hello guys guide on how to make a Dual Coil on Iatty. I beg your pardon for English, I hope you understand that the guide.
First you need to change the ceramic cup, I used a dremer and gradually I extended the two side slots so as to easily get one over the other 2 wick.
After that we take our non-resistive and resistive wire and cut 2 pieces of wick of about 5cm. I chose the size of the wire to be able to do 0.13 for 2 3/3.2 ohm resistors, but you can use the wire you want. Cut the wires and we get the right size 2-wire resistive, 2 long and 2 non-resistive resistive short.
Now you must proceed as you normally would to make the resistance, but instead of making it are making it a 2, using a 2-wire resistive and using long and short. Now you put them on top of each other and add the resistive wires.
At this point enter the 2 resistors in the cup and reinsert the 2 o-rings underneath the ceramic glass, then put it in the first plastic part.
Connect the two wires resistive as always, and trimmed the wick 2, those of about 2.5cm let them down while the upper end bicchierino.Per let them flush with the upper glass screw the adjustment for the liquid you're using (the densest = more unscrewed and vice versa)
Now you can screw the main body of iatty, the top cap and mouthpiece ......
The first time I did this mod I used the wire I 2 0.16 and 3.0 ohm resistors, I do not know why but I had problems with flooding, and the second time using the wire from 0.13 and everything went very well ....
My first impressions are: Smoke good, very good heat, aroma and sensational hit, I tried it on Provari that made me push up to 4.5v without absolutely no flavor of wick and burned, while the maximum is of course GGTS was up 4.2 down to 3.7V ..... what else to say guys I am really happy with this mod is the first time I hear so well with the aromas iatty. As mentioned earlier, the first time I had problems of flooding, I do not know what caused it, but I think it depends on how you put their wick as putting too wide apart, and spends too much liquid is flooded .. ....
Well guys I have shown how to make, of course I did not presume to say that is a perfect and infallible, and I wish each of you after trying to tell me his impressions as well as suggestions for improving it.
Greetings to all
):
First you need to change the ceramic cup, I used a dremer and gradually I extended the two side slots so as to easily get one over the other 2 wick.
After that we take our non-resistive and resistive wire and cut 2 pieces of wick of about 5cm. I chose the size of the wire to be able to do 0.13 for 2 3/3.2 ohm resistors, but you can use the wire you want. Cut the wires and we get the right size 2-wire resistive, 2 long and 2 non-resistive resistive short.
Now you must proceed as you normally would to make the resistance, but instead of making it are making it a 2, using a 2-wire resistive and using long and short. Now you put them on top of each other and add the resistive wires.
At this point enter the 2 resistors in the cup and reinsert the 2 o-rings underneath the ceramic glass, then put it in the first plastic part.
Connect the two wires resistive as always, and trimmed the wick 2, those of about 2.5cm let them down while the upper end bicchierino.Per let them flush with the upper glass screw the adjustment for the liquid you're using (the densest = more unscrewed and vice versa)
Now you can screw the main body of iatty, the top cap and mouthpiece ......
The first time I did this mod I used the wire I 2 0.16 and 3.0 ohm resistors, I do not know why but I had problems with flooding, and the second time using the wire from 0.13 and everything went very well ....
My first impressions are: Smoke good, very good heat, aroma and sensational hit, I tried it on Provari that made me push up to 4.5v without absolutely no flavor of wick and burned, while the maximum is of course GGTS was up 4.2 down to 3.7V ..... what else to say guys I am really happy with this mod is the first time I hear so well with the aromas iatty. As mentioned earlier, the first time I had problems of flooding, I do not know what caused it, but I think it depends on how you put their wick as putting too wide apart, and spends too much liquid is flooded .. ....
Well guys I have shown how to make, of course I did not presume to say that is a perfect and infallible, and I wish each of you after trying to tell me his impressions as well as suggestions for improving it.
Greetings to all
):
..........
