Indulgence Mt-Rta

[haleysdadda]

Ok, Ok, I know. But I couldn't stand it. The new screws will have to wait for the next rebuild. I ran dual parallel (thanks to @MMW for reminding me why I like them) 28ga, 6/5 wrap on a 3mm mandrel for .4 ohms. I measured out at .38 ohms when I got it built. When I test fired it, I got one of the prettiest center-to-ends burns I've ever seen. I wicked it up, but I may have left one of the channels a bit shy. I'm still watching it to see if it's gonna leak. Not yet, though. Does she vape? Lord love a duck! She's a cloud chucker and no mistake. I love how the tank breathes; it's nearly unobstructed. Tested it at 30 watts, it was great. Ran it up to 35, it was better. Tried 40, seemed to burn the juice a tad. Backed off to 38 and she's just a steamthrower, is all I can say. I'm vaping it now, although I intended it for my car mod and it's loaded with the DIY Cinnamon Red Hots I use for my ADV. Partly because I want to watch for leaks, and partly because I want to vape it past the rayon break in to taste the juice a bit better and play with the wattage some. Thank you, one and all, for talking me into buying it. I've been looking for this tank for some time. Years, actually

View attachment 512320 View attachment 512324 View attachment 512325 View attachment 512326 View attachment 512327

More wick! More wick! The new screws will be awesome but not worth waiting for! Welcome to vaping nirvana!

 

[suprtrkr]

More wick! More wick! The new screws will be awesome but not worth waiting for! Welcome to vaping nirvana!

I dunno how I'm gonna get more wick in it, it was already tough pulling it through a 3mm coil. Hhhmmm... Perhaps a rayon strip on the deck.

 

[suprtrkr]

Query: Does this beast have the standard top-fill tank complaint of puke a few drops when you put the lid on? It's not leaking when I stand it up, at all. But it puked a few drops down into the air channel-- gotta love a tank with air channels big enough to see this-- when I laid it down in the case after I refilled and (I thought) prepared it to go out in the morning. Yes, more wick indeed. I love it all to pieces already, but I'd actually like it better if I could lock the air ring in place. I run it wide open, I guess I could just leave it off.

 

[roxynoodle]

Did you invert it for that half turn of the top cap? Mine haven't puked.

 

[kushpancake]

Yep! Just tap it back together! No harm no foul!

That's exactly what i did. Chuckin' like a champ on some Holy Grail Strawberry Fields 6mg - 26g ka - 8/9 wrap - 2.8mm - 33.3w - .5 ohms

 

[kushpancake]

Anyone know a good build with either 24 or 26g that would be hot and be good on a sigelei 50w?

sent from my dirty shamu

 

[suprtrkr]

Did you invert it for that half turn of the top cap? Mine haven't puked.

no. But I will in the future.

 

[haleysdadda]

I dunno how I'm gonna get more wick in it, it was already tough pulling it through a 3mm coil. Hhhmmm... Perhaps a rayon strip on the deck.

Leave your tails longer. I don't trim mine until after I put the chimney on.

 

[Adam harris]

I wish I could get used to the stock drip tip that comes on the tank..
If only it was a little longer..

 

[Bman123]

Put a different one on there

Sent from my Nexus 6 using Tapatalk

 

[suprtrkr]

Leave your tails longer. I don't trim mine until after I put the chimney on.

I did. But I will leave them longer in the future. Rayon is cheap, lol. Those are some fearsome big juice channels, for a fact. It's not leaking, so WTF. I can't complain. I need a better juice bottle, though. I've been using the Ucan, but it doesn't hold/pour fast enough for the way this thing drinks juice.

My, oh my, do I like this thing. I vaped a tankful this morning, then switched back to a Fogger V6 I had filled and included in the kit, in case the MT decided to develop a problem, and it's practically nonexistent in comparison.

 

[roxynoodle]

I wish I could get used to the stock drip tip that comes on the tank..
If only it was a little longer..

The Crius ones suit the MT better. And the MT ones aren't bad on the Crius.

 

[Adam harris]

The Crius ones suit the MT better. And the MT ones aren't bad on the Crius.

I heard the crius tank isn't that good.

 

[Adam harris]

Put a different one on there

Sent from my Nexus 6 using Tapatalk

I did.

 

[Bman123]

I did.

I did too, I put a really wide bore one on mine

Sent from my Nexus 6 using Tapatalk

 

[roxynoodle]

I heard the crius tank isn't that good.

I could live without them. But, I've spent too much money on them since I bought v2s and then bought v3 decks so I'm keeping them.

 

[Adam harris]

I could live without them. But, I've spent too much money on them since I bought v2s and then bought v3 decks so I'm keeping them.

I realized I spent almost 200 dollars last month on vaping stuff so I'm done buying.

200 dollars in a month made me want to puke.

But I have 2 gallons of VG and a gallon of pg...a liter of nicotine..an istick100 and plenty of tanks and drippers and 2 mech mods so I'm going to just use the diy flavors I have left and go from there..

 

[suprtrkr]

I tried the inversion thing when I refilled. 'Pears to have worked. It didn't puke much if any.

 

[Adam harris]

I did too, I put a really wide bore one on mine

Sent from my Nexus 6 using Tapatalk

If you have a goblin try the tip from the mt on it..It looks good on mine. The regular goblin..not the mini

 

[Bman123]

I realized I spent almost 200 dollars last month on vaping stuff so I'm done buying.

200 dollars in a month made me want to puke.

But I have 2 gallons of VG and a gallon of pg...a liter of nicotine..an istick100 and plenty of tanks and drippers and 2 mech mods so I'm going to just use the diy flavors I have left and go from there..

I spent a little more then that last month but it was for 4 Gallons of VG a litre of Nicotine and 100 30ml unicorn bottles

Sent from my Nexus 6 using Tapatalk