Indulgence Mt-Rta
- Thread starter 98ruby
- Start date
- th_trl_thread_readers 0
- Status
Just got my MT rta. Usually a pre-built coil man, but decided to go this way. Semi-wishing that I waited for a Mutank to come in stock but then I know I would just be lazy and use the pre-built heads. This is my first RTA. Anyone have any tips for building/wicking outside of really packing the channels with cotton?
Make sure your coil is as wide as the air hole, my first Clapton coil wasn't as wide and I got a lot of leaking. Like the juice was falling off the cotton and going down the airholes.
Sent from my Nexus 6 using Tapatalk
My local Vape shop is really good about getting new stuff asap and they have them already for $40.
I don't want to spend $5 a coil every other week when I can spend $15 on a roll of Clapton wire and a pack of cotton pads and build coils for 6 months in my rta and rda
Sent from my Nexus 6 using Tapatalk
The ratio varies as the diameter of wires: (Base Wire Diameter x Pi) of the small wire per each (Wrap Wire Diameter) length of base wire. 28/32, the wrap is about 4.6 times the length of the base wire. I haven't yet calculated the cost. Substantially less than $9 for 15 feet, I feel sure.
What wire and mod are you using? There's quite a few pics in this thread.
Here is my build that I have been pulling on for a week.
Indulgence Mt-Rta
Mine is presently set up at .3 ohms, 28ga parallels, 5/4 wrap on a 3.5mm mandrel, that currently being the largest mandrel I have. I am considering getting a 4mm drill bit to get more wick in it. In any event, it hits like a cannon.
Sounds good. I buy my kanthal direct, but I use LV's Nickel200. They're good people.
Thanks everyone for the feedback. And thanks MMW for the link back in the thread, those pictures are extremely helpful. In response to your question about mod/wire:
The MT will be going on a DNA200 device. I use my Boxer DNA133 and Reuleaux the most. As far as wire, I have some spider silk titanium 26 gauge, but I wasn't able to get that going quite right on my Opus and Velocity as I am pretty much new to building so that wasn't the best place to start. I think I might just start this time with some 20 or 22 gauge (more likey the latter) kanthal to learn how to build first before trying to do NiFe or spaced titanium coils. At some point I may order some of the Youde clapton wire as well but I feel like the kanthal is a good place to start for me.
The MT will be going on a DNA200 device. I use my Boxer DNA133 and Reuleaux the most. As far as wire, I have some spider silk titanium 26 gauge, but I wasn't able to get that going quite right on my Opus and Velocity as I am pretty much new to building so that wasn't the best place to start. I think I might just start this time with some 20 or 22 gauge (more likey the latter) kanthal to learn how to build first before trying to do NiFe or spaced titanium coils. At some point I may order some of the Youde clapton wire as well but I feel like the kanthal is a good place to start for me.
Right on. I'm a straight kanthal fella myself. I will be trying Ss soon though. Throw in a simple build and wick it up! We will be here if you have any issues.
Haha yes I am. Will let ya know for sure. Hope the griffin is nice. Wicking on it looks like the mt just the wick holes do not go all the way through. But looks super easyYou're becoming an RTA ....! Nicely done sir! I'm waiting for your assessment of that crius clone. Is it the Griffin?
@haleysdadda are you sure that m2.5x4mm is the right size? these new screws are tiny compared to other grub screws i have for my derringer and freakshow mini rdas. I guess the only way to tell is by trying it out right? haha I was just waiting to finish my tank of juice before i did. Will post an update shortly.
Update: they fit like a charm and screw down nice and tight. HIGHLY recommend this to everyone with this RTA.
Update: they fit like a charm and screw down nice and tight. HIGHLY recommend this to everyone with this RTA.
Last edited:
Looks like they fit! Kool! My only concern is the screws you bought are steel & may rust! Keep an eye on them!!@haleysdadda are you sure that m2.5x4mm is the right size? these new screws are tiny compared to other grub screws i have for my derringer and freakshow mini rdas. I guess the only way to tell is by trying it out right? haha I was just waiting to finish my tank of juice before i did. Will post an update shortly.
Update: they fit like a charm and screw down nice and tight. HIGHLY recommend this to everyone with this RTA.
Pretty build! I love the way those screws look!
Was gonna order my mt today from vapordna but u guys got me wanting it MEOW. Gonna call around to vape shops within a 25 mile radius and see if I can pick one up today
I made the mistake of ordering it. The wait for vapemail was unusually painful.Was gonna order my mt today from vapordna but u guys got me wanting it MEOW. Gonna call around to vape shops within a 25 mile radius and see if I can pick one up today
I'm vaping it now on my SX Mini.- Status
