Indulgence Mt-Rta

[MMW]

Me too.

 

[haleysdadda]

The hex ones?

No, I hate the grub screws.

Sent from my Nexus 6 using Tapatalk

Me too.

And I humbly ask a newbe why?

 

[Bman123]

I don't like them because the ones that come with rda's most of the time are junk and the hex key they give you is almost guaranteed to be a turd. I'd rather use a Phillips head screwdriver

Sent from my Nexus 6 using Tapatalk

 

[ThunderDan]

Kool! Cuz Lowes & Home Depot didn't have them!

I got mine at Grainger. Mainly because I don't have an Ace, or True Value, or a real hardware store near me.

 

[haleysdadda]

I don't like them because the ones that come with rda's most of the time are junk and the hex key they give you is almost guaranteed to be a turd. I'd rather use a Phillips head screwdriver

Sent from my Nexus 6 using Tapatalk

The first Atty I ever bought with them in it they really sucked http://tkovapor.com/atomizers-cartomizers/authentic-rda/tko-vapefuel-rdta.html Kinda a cross between a big dripper a Mutation like x2 I believe. More of a novelty than a serious RDTA!). But you haven't tried store boughts with a real allen wrench?

 

[Jvincent516]

Hey everybody thanks for the suggestions, I just tried a basic 24g 8 wrap dual coil at .36 and I can't believe the flavor I'm getting off this thing. I think I'm in love lol. I need to mess with the wicking the first tank was perfect but got a little leaking when I filled it back up. I can't wait to try different builds.

 

[arh32]

What I found best for wicking was for coils that are 3mm wide, I cut a strip of KGD that is about twice the width of my coils, take the outer skins off (no clue if this does anything, its just my method to my madness), and gently roll it on my pants to make it a loose log. thread through the coil... Now here is where its different from MOST rda's, I have to have the cotton kinda tight in the coil.... then I wet the wick in the coil and about 3/4 inch past it both ways. using a bent paperclip I poke and prod the wet wick into the juice slots until they stay and I can thread the top on over the Deck. Snip the wicks about 1/16th or just a smidgen longer from the juice wells and then gently poke them back so they are flush with the edges of the holes. screw on the glass portion and fill it up. Haven't had a leak or dry hit when doing it this way.

There are lots of ways to wick this thing. This is one of the best I have tried. Its so easy and get this, I have small air bubbles from every wick hole now!!! 24ga 5wrap .3id at .28 ohms and this thing is wicking like a champ. I find that i dont need lots of watts with this sep up for some reason i am happy at 30w atm. Edit just went to 65w no problem, went down to 20w and still has plenty of vapor and flavor!!! Loving this setup

 

[haleysdadda]

JUST BOUGHT THESE! 10 STAINLESS STEEL 2.5mm x 4mm Socket Set Screws Grub Cup Point + 1.3 Hex Key
WILL LET YOU GUYS KNOW! NOT YELLING! JUST EVERYTHING AT WORK ALL CAPS!

 

[haleysdadda]

Hey everybody thanks for the suggestions, I just tried a basic 24g 8 wrap dual coil at .36 and I can't believe the flavor I'm getting off this thing. I think I'm in love lol. I need to mess with the wicking the first tank was perfect but got a little leaking when I filled it back up. I can't wait to try different builds.

You have the same rig I do except mine is stainless tank! May have to divorce the wife and marry mine!LOL!

 

[EverPresentNoob]

@EverPresentNoob, yep! That's pretty much the way I wick it. I don't roll it but everything else is spot on. It's definitely a lot easier to form in the channels when wet. It does like a nice wick!

So, you're digging the output?

Lovin the output. its a little warmer vape than my crown with a .25 head at 75 watts, but running my dual 22g 3mm id 5 wrap coils at 70 watts is the same otherwise. Right now Im thinking its replaced my TFV4. It has better flavor and dosent suck the juice quite as bad. and since I build my own coils in the mutation I dont have to drop 25 bucks or so for 5 new heads. The crown is about damn even with the mutation, but I give the nod to the mutation right now simply for the cost factor, building coils compared to buying heads. Airflow is about the same between the two and I run mine wide open on both.

 

[MMW]

Wooooo! Right on brother!

 

[Afcarmona]

JUST BOUGHT THESE! 10 STAINLESS STEEL 2.5mm x 4mm Socket Set Screws Grub Cup Point + 1.3 Hex Key
WILL LET YOU GUYS KNOW! NOT YELLING! JUST EVERYTHING AT WORK ALL CAPS!

off to fleabay i go...

 

[haleysdadda]

So I've noticed that the "ONLY" time I get "any" leaking is when I "Top off" a tank! Never on an MT (pardon my humor) tank. Anyone?

 

[roxynoodle]

I haven't had any leaking at all. I have had a small bit of condensation spittle come out an airhole twice when I didn't inhale all the vapor. A very, very small amout of mist.

 

[haleysdadda]

I haven't had any leaking at all. I have had a small bit of condensation spittle come out an airhole twice when I didn't inhale all the vapor. A very, very small amout of mist.

I get the spittle too! guess my "perfect" wicking isn't that perfect. Doing a build longevity test right now so I'll have to wait. 1 week so far just refilling nothing else!

 

[roxynoodle]

I get the spittle too! guess my "perfect" wicking isn't that perfect. Doing a build longevity test right now so I'll have to wait. 1 week so far just refilling nothing else!

More like not letting off your fire button soon enough

 

[Jvincent516]

I get leaking when I top off my tank also, but I'm going to put a new build in my tank and try to perfect my wicking, to see if that eliminates the leaking.

 

[arh32]

The link for grub nuts on ebay; m2.5 grub screws in Industrial Supply and MRO Products | eBay. Looking for some USA shippers.

Ordered Thank You for the link!!!!!!!!!!!!

 

[Bman123]

I definitely messed up my last wicking job, she's a leaking lol. Oh well I'll fix it tonight

Sent from my Nexus 6 using Tapatalk

 

[Paul.K]

Finally got my wicking right and no more leaks. This is performing very well on single coil @ 30 watts. Just ordered another one.