IPV3+ Panasonic NCR18650B 3.7V 3400mAh?

[drz400dude]

So I just picked up an IPV3 from a buddy that was getting rid of it for cheap, but he kept his batteries. I got a set of panasonic NCR18650B 3.7V 3400mAh batts. Are these good to use in the IPV3?

Specs of the website:
*Panasonic NCR18650B Super Max 3.7V 3400mAh Rechargeable Li-ion Battery-Green
*Brand Panasonic
*Color Green + black
*Material Lithium
*Quantity 2
*Type Lithium ion
*Model 18650
*Mark Capacity N/A
*Actual Capacity 3400mAh
*Battery Voltage 3.7 V
*Rechargeable Yes
*Rechargeable Times 1000
*PCB Protected Board No
*Application Flashlights and various household electronic products
*Packing List 2 x batteries
*Dimensions: 2.56 in x 0.71 in x 0.71 in (6.5 cm x 1.8 cm x 1.8 cm)
*Weight: 3.21 oz (91 g)

Thanks for the help.

 

[djsvapour]

You can vape with them, but DO NOT use these in high power devices.

Oh.. and Welcome

(I just noticed!)

 

[tj99959]

With only a 2c rating (6.8 amp), it is not an acceptable battery for vaping.

You should use 30 amp batteries in that 150 watt mod.

 

[drz400dude]

The IPV3 is 150W. I read not to go above about 30W with these batteries. I'm running a .6 ohm coil. I am an A&P mechanic and understand Ohms law as it pertains to electrical circuits on aircraft, but I'm not sure how these things work yet. Should I get different batteries just to be safe? If so which would work best? I got them because the 3400mAh looked appealing, and they seem to be lasting a long time.


Thanks for the quick reply and the welcome!

 

[Susan~S]

Not good for your IPV3. Not good for most mods as that battery has a low CDR (continuous discharge rating). Save them for your flashlights.

At the VERY LEAST you need a 20A CDR battery (30A is recommended due to the 150watts). I use the Sony VTC4's when I need 30A's and Samsung 25r's when I only need 20A's. RTD Vapor is my go-to for batteries.

18650 Batteries

1. Orbtronic SX30 2100mah 30A
2. Sony VTC4 2100mah 30A (there are no authentic VTC5's out there)
3. Xtar 2100mah 30A (re-wrapped Sony VTC4)

1. AW 1600mah 24A
2. Orbtronic SX22 2000mah 22A
3. LG HE2 2500mah 20A
4. Samsung 25R 2500mah 20A
5. AW 2200mah 20A (new)

BATTERIES - WHERE TO BUY

Only buy batteries from a reputable supplier (not ebay or Amazon) as there are many counterfeit batteries being sold. Here are several reputable battery suppliers in the US.

* RTD Vapor
* Illumination Supply
* Lighthound
* Orbtronics

 

[drz400dude]

Thanks. Should have done more research before I bought them I guess. I just got a little anxious and excited. One last question, will the panasonics HURT anything if I use them for another week while I wait for other batteries to come in? If I keep the amperage draw below the 6.8A battery spec?

 

[djsvapour]

Thanks. Should have done more research before I bought them I guess. I just got a little anxious and excited. One last question, will the panasonics HURT anything if I use them for another week while I wait for other batteries to come in? If I keep the amperage draw below the 6.8A battery spec?

It uses two x 18650s?

I use these batteries on other 'old' mods and there must be some level at which they are safe. I don't know enough about it to give an honest reply.

 

[Baditude]

Those Panasonic 18650B 3400 mAh batteries were designed for flashlights. Our vaping "hobby" requires a high drain IMR battery with at least 10 amps continuous discharge rate. Those Panny's only have 6 amps.

Don't be fooled by the high capacity 3400 mAh. That only applies for a low draining device like a flashlight. You'll probably only get half that time on a mod, and it won't perform to its optimum standards using them.

 

[drz400dude]

Thanks Baditude, I realize this now.

I'll order some proper ones and just keep the current under 6A for now. I just wanted to make sure they weren't going to blow up in my face or destroy my new toy.

Thanks for the help everyone!

 

[realsis]

When you purchase the IPV3 from the company, they WARN do NOT use lower than 30 amp batteries in the unit. I also have a IPV3. 150. That said, you are aware of the risks at going above the 6.8 amp. In fact if those batteries are rated 6.8 amp I would keep it well below that if possible. You don't want to push them to their maximum rating in my opinion because sometimes ratings can be off a bit. If you can keep in well under that until you receive your batteries you "should" be alright but I'm not going to advise one way or another because their IS a risk and I would hate to have something happen. With that said and the factory warning, I would just play it SAFE and not use them at all. You could easily push them to their maximum limit and it might or might not be alright. That's just my opinion. I play it safe. It's however up to you. Just keep in mind that their MAXIMUM is 6.8 amps. I wouldn't risk it. Ultimately it's your decision. I wish you the best and hope you enjoy your new unit! I know I really enjoy mine! I think you will be happy with it! Best of luck.

 

[EBates]

Welcome aboard
IIRC the IPV3 uses 2 batteries in series, so the batteries should be married (used in pairs). This may not be an issue if you're not pushing the battery current limits. Just an FYI