JonboyUSMC's Lava Tanks
- Thread starter jonboyusmc
- Start date
- th_trl_thread_readers 0
- Status
Me either, but hubby said brass can be sharpened with a file. Don't know how fine a hole it will make.
From what I've read the 1/4" vs 3/8" is the size of the plastic hose the would be attached to the valve. The clamp and punch part we use would be the same.
OK, these have been around for a long time, I'm gonna get one at HD, I think I could remove the pin and carefully spin it while running it on my belt sander to sharpen the pin to a real fine point hopefully, this will work good on a part I'm making, thanks everyone !
interesting... i have the 1/4 in too, but the hole i punched is definitely smaller than the one you pictured.
Yeap, Here is how it look punched with it.
It will punch the hole smaller but if you tighten it in a little more it will open the hole.
Thanks, first pics I've seen of magma with a regular carto in it.Okay, here's the picture of our Magma and Lava's
Black Delrin Magma on a Purple Silver Bullet (not released yet)
Magenta Bliss Lava on a Purple BB
Old Glory Lava on a Silver Bullet
--------------------
Again, another question (anyone?) which has probably been answered in this over 19,000 post thread
but has anyone measured how much juice will fit in the regular and magma tanks (assuming carto in the tank and for re-fill or after prefilling the carto if first fill)? My other standard tanks seem to only take about 1.2 ml (leaves an air-bubble about the size of a small lima bean).My preferred carto is the Boge JCA302 (most often referred to as 801 at Nhaler or fusion at Ikenvape) and it fits my other standard carto tanks (has 510 size tube but adds a base collar flared out to accommodate the 801 threads - also stops other tanks from sliding down). Just want to clarify all info as the new ones are getting close.
Will use on my Darwins, Empire, perhaps GGTB, and future devices(?). 1.2 ml fills require less refilling than just the carto (sans tank) so the magma may be worth the width for the extra capacity and extra tube thickness even if it will overhang the Empire and look a bit funny on Darwins.
I got my 3 amp adjustable voltage regulators from Dimension Engineering today. One of these, some wire, a switch, a 510 connector and two batteries are all you need to make a VV mod. Here is a pic of the top and bottom of them. I put them next to a 16340 battery for scale.
Afternoon all...actually took a nap, trying to shake this cold, but didn't help much...LOL!
Sounds like you have what I and Wolf are just getting over..... up your vitamin C intake....can't hurt. and if it gets into your chest, call a dr....you will need an antibiotic.....
Gawd, this one was a hanger on big time. Just when you start to feel better, it comes back again.....
Sorry you caught it Ty.
Does anyone here mix their own e liquid? I have some TPA flavors like caramel cappucino and kona coffee. Was wondering if anyone had any suggestions on mixing this. If anyone is able to help, thanks in advance. I'm frustrated right now because I am why in the H I got the flavors not knowing how to mix them!!
Thinking about taking a nap myself. Got out of bed this morning at 8 because I couldn't breath through my nose. That's really saying something considering I use a CPAP machine, so have air being forced through my nose.
Okay, here's the new work of art (hopefully, I can snag a work of art to go with it):
If you go to Gormet Vapor you can search on hundreds of recipes. Then download the ejuicemeup calculator and plug in your nic mix and flavor percentages and what percent you want your mix to be and it will tell you how much of everything to add to the bottle. Breakthru has a forum support board also if you need help.
- Status
Similar threads
- Locked
