JonboyUSMC's Lava Tanks
- Thread starter jonboyusmc
- Start date
- th_trl_thread_readers 0
- Status
Good evening everyone. Hopefully someone will make it to VaperCon2 this weekend and be able to report back on the LavaGen (if Dino will give anyone a chance to try it). Hope everyone has a great weekend....I'm going to try and find some time to just relax...
Nice review almighty,good job jonboy keep the wick hole small much better for those to make a hole bigger if airy draw is wanted easy to drill hole bigger but some do want a tighter draw i think that would cater to more of your followers being carto tank users.
A little Lava Tank porn for a Sunday afternoon....
Awesome lava tank porn!!
Good evening lavacorps!!
So I had a chance to try out the LavaGen at Vaporcon that Dino had, and I am telling you all something!! It is definatly a device that will be worth having!! Very nice!! Can't wait to get one, or two, or.....!!!! Thanks for the chance to try one out!!
I have my beta and haven't even had a chance to get a wick rolled up and oxidized yet. I will get to it soon, though, can't wait to try it out. I tried Dino's as well and they do hit great.
Oh, I know it's the wrong thread but I'm really glad Mike took care of your wife, Junky. I may've seemed indifferent at the time but it was only because so much was going on at the time, my attention was totally divided. That sucks someone would do that.
Thank you to the Lava Corp for watching the show last night.
I had a good time running through the Lava Gen set up with you!
I had a good time running through the Lava Gen set up with you!
Here's some instructions on setting up the LavaGen:
Picture of the positive post not extended
Advance the positive post until it protrudes slightly past the bottom of the 510 connecter. This is done by rotating the positive post clockwise.
See the post in the correct position.
Slide on the bottom cap of your Lava Tank or Reactor Tank
Thread the genesis on the mod. Snug....DO NOT OVER TIGHTEN.
Notice the small spacer under the ground screw. Notice the positive connecter. Large spacer on the bottom, small spacer above that, followed by the thumb screw.
Here is a pic of a coil set up in the genesis. Notice the ground lead is connected under the spacer on the ground screw. The positive lead is connected in between the large spacer and the small spacer on the positive post.
Here's another view
Here is another view of it with the wick installed.
Slide your top cap....position the air hole before snapping the tube fully on the bottom cap.
Here is a shot of the inside of the completed setup.
This is the beginning of the setup for using horizontal silica wick. The coil should be wrapped counter clockwise. The negative lead should be on the top of the spacer on the ground screw. The positive lead should be in between the large spacer and the small spacer on the positive post. Wrapping the coil counterclockwise ensure a level setup. Wrapping the coil clockwise will cause the coil to sit crooked.
Another shot showing how the ground lead is connected.
Another shot showing how the positive lead is connected.
Slide one piece of 3mm silica wick....from silica wicks.com....through the wick hole.
Ignore the second wick hole....this is a beta and the final production model will not have that second wick hole.
Take a double 3mm wick, wrap your coil and connect as previously shown.
Ignore the second wick hole....this is a beta and the final production model will not have that second wick hole.
Notice I have cut the excess wick from the ground screw side....this is so there is nothing in the way when the tube is placed on the genesis.
Ignore the second wick hole....this is a beta and the final production model will not have that second wick hole.
Notice I have cut one of the two tails....leave one long to wrap around the back side of the positive post to catch any juice that should happen to come out of the fill hole.
Notice that I have fanned out the top of the piece of silica that is in the wick hole and also that it is touching the coil. This will help the wicking.
Ignore the second wick hole....this is a beta and the final production model will not have that second wick hole.
Here's a shot of the completed silica wick setup.
Complete.
Picture of the positive post not extended
Advance the positive post until it protrudes slightly past the bottom of the 510 connecter. This is done by rotating the positive post clockwise.
See the post in the correct position.
Slide on the bottom cap of your Lava Tank or Reactor Tank
Thread the genesis on the mod. Snug....DO NOT OVER TIGHTEN.
Notice the small spacer under the ground screw. Notice the positive connecter. Large spacer on the bottom, small spacer above that, followed by the thumb screw.
Here is a pic of a coil set up in the genesis. Notice the ground lead is connected under the spacer on the ground screw. The positive lead is connected in between the large spacer and the small spacer on the positive post.
Here's another view
Here is another view of it with the wick installed.
Slide your top cap....position the air hole before snapping the tube fully on the bottom cap.
Here is a shot of the inside of the completed setup.
This is the beginning of the setup for using horizontal silica wick. The coil should be wrapped counter clockwise. The negative lead should be on the top of the spacer on the ground screw. The positive lead should be in between the large spacer and the small spacer on the positive post. Wrapping the coil counterclockwise ensure a level setup. Wrapping the coil clockwise will cause the coil to sit crooked.
Another shot showing how the ground lead is connected.
Another shot showing how the positive lead is connected.
Slide one piece of 3mm silica wick....from silica wicks.com....through the wick hole.
Ignore the second wick hole....this is a beta and the final production model will not have that second wick hole.
Take a double 3mm wick, wrap your coil and connect as previously shown.
Ignore the second wick hole....this is a beta and the final production model will not have that second wick hole.
Notice I have cut the excess wick from the ground screw side....this is so there is nothing in the way when the tube is placed on the genesis.
Ignore the second wick hole....this is a beta and the final production model will not have that second wick hole.
Notice I have cut one of the two tails....leave one long to wrap around the back side of the positive post to catch any juice that should happen to come out of the fill hole.
Notice that I have fanned out the top of the piece of silica that is in the wick hole and also that it is touching the coil. This will help the wicking.
Ignore the second wick hole....this is a beta and the final production model will not have that second wick hole.
Here's a shot of the completed silica wick setup.
Complete.
Hi Pain...Thanks... I have so much fun matching all my Lava Tanks to the lovely Bedazzle tubes
Hope things are going well for you...work is crazy busy, but I have to work to buy all of vaping toys...
Hope things are going well for you...work is crazy busy, but I have to work to buy all of vaping toys...
Yeah…I'm going to have to get one of these when you start selling full kits.
- Status
Similar threads
- Locked
