Oh yeah....aqua clear tanks $12 https://www.ultravaping.com/ProductDetails.asp?ProductCode=H-TA-AQUATUBE
- Status
Keep an eye out, I was looking the other day and there were several places that iirc either had some and were a little more money and/or were expecting them soon.
lol I got the last flash-e V2 from white stag for $50 the day before FT came out with them for less than half
But they are offering a pre-order for the aqua, not sure when they are due in but they responded fairly quickly to my questions when I submitted via the contact on their site.
Aqua clone RBA - White Stag Vapor
Thanks bap the clone does have flow control, right?
I'll be heading to the pet store today for brushes finally…any recommendations? I've watched a 'carding wool' with pet brushes video on youtube and it seems its best to have two brushes?
These are what I got, but neither seem to work as good as I would like and I still end up doing most by hand.
Nice bap, thank you. When you do it by hand do you just pull things apart until the knots go away?
Yeah, or if it's real bad I just pull off what I can and toss the little knotted piece.
sounds good, i'll keep ya'll posted. I've already pulled off some for my trident and nimbus and it worked out fine, stellar performance thus far. I just wanted to see if I could restore some of the texture of the pre wash stuff for packing my vertical coil builds.
throw the stuff back into a water bath - swish it around and pull apart if necessary
carefully scoop it out and let air dry. i got most of the fluff back doing it that (mike's) way 
Have one of them coming, the tank is small, so ya want to know where you are
Yeah plus it's nice to visually see where the flow control is.
I think it looks pretty good as well
Anyone try one of these?
A Rip Tripper quad on an rsst.
My first attempt. Only problem-run out of juice too quick.
28ga. 2 ohm, pluid with hemp wick.
I think I like Pluid on an AO w/ni foam better for flavor.
Maybe just need some break-in time.
A Rip Tripper quad on an rsst.
My first attempt. Only problem-run out of juice too quick.
28ga. 2 ohm, pluid with hemp wick.
I think I like Pluid on an AO w/ni foam better for flavor.
Maybe just need some break-in time.
Last edited:
Built me one last night. Mine comes out to 1.9 but it needs more than even my 18650's can give it without VW. Otherwise, I'm impressed with it.
Black RSST? Richman?
Sent from my ME173X using Tapatalk 2
Just lighting. It's an rsst. Yea, needs 'bout 14 or 15 watts to make it shine.
So i just tried the degummed hemp fiber in the russian 91. I love it. Wicks better than cotton, and i will see how long it last. Only thing i will do next time is clean with oxy and then boil lots. I did a boil for about 30min and can still taste the hemp. Other than that i think i am done with cotton. Thank you all for telling how to clean it. Very Happy!!!!!
I was in the same boat boil didn't do it. What I did was soak it in stabilized clorine dioxide over night, just enough to soak it, and a simple rinse and dry it was pure flavorless. Clo2 is commonly used in specialty mouthwashes like closys.
I've finally got it working for me on my vertical oddy build. I found I needed to use a little more dense wick in the oddy than I was with rayon. Also fill more into the ceramic. Just 2 wicks with some tuft I to the outside gaps. No more core wrap is an easier wick job.
I've finally got it working for me on my vertical oddy build. I found I needed to use a little more dense wick in the oddy than I was with rayon. Also fill more into the ceramic. Just 2 wicks with some tuft I to the outside gaps. No more core wrap is an easier wick job.
Last edited:
- Status
Similar threads
- Locked
