Kanger EVOD
- Thread starter James Tank
- Start date
- th_trl_thread_readers 0
-
- Tags
- evod myvaporstore provari vamo
- Status
Odd, one of my EVODs will gurgle like crazy after only vaping about a quarter of the fluid, then it starts leaking like hell. The other one, perfectly fine. I've taken it apart and tried tightening down the center post to the base, but nothing helps it.
my EVOD hasn't arrived yet, so i cannot give any advice,about your comment CID78, i thought this EVOD still inherit the character of T3 which is working on thicker liquid,....in T3, i already can solve the gargling and leaking issue,...hope soon after my EVOD arrive, i can find what happen and can solve this matter...
CID....when my EVOD comeee????
I had the same leaking, gurgling problem with one I bought. I am a noobie so I thought that it might have been my error or a defective unit...but I just checked and my unit was just loose. I fixed it and it works like a charm!!!
Last edited:
i have had mine 6 days i have put it through its paces works great 2
thumbs up . a few dry hits just re prime and its fine a few gurggles just blow out
and its fine , i have also switched flavor vaped right into next flavor no problem .
thumbs up . a few dry hits just re prime and its fine a few gurggles just blow out
and its fine , i have also switched flavor vaped right into next flavor no problem .
Sun-Vapors and MyVaporStore both have them in multiple colors. MyVaporStore is a few pennies higher priced, but they also have a 10% discount code you can find down in the supplier forum.
Oh ya. That's where I bought two just last week.
I bought a couple more today from Sun-Vapors because iVape is out of black and stainless.
anyone tried to rebuild them ? I had a go at it and I cant seem to make it work. I'm using 2.5mm wick and some wire, when i twist it 4 times its 2.7 ohm and 3 times its also 2.7 ohms what is up with that ? They should be same to rebuild like t3 and nova, why cant i make it work? I think it doesnt' wick properly also
GotVapes just started carrying them.
I still cannot figure out why one of my EVODs leaks so badly now. Two of them are perfect, except for, just like the T3, once the juice gets real low, then it starts to gurgle. But one of mine just starts gurgling after only about 5-10 hits.
I still cannot figure out why one of my EVODs leaks so badly now. Two of them are perfect, except for, just like the T3, once the juice gets real low, then it starts to gurgle. But one of mine just starts gurgling after only about 5-10 hits.
I have been using my new EVOD most of the day today and I'm very impressed. Almost through my second tank and no leaks, gurgles, spitting or cussing LOL. Popped it on my mini eGo and the thing vapes like a champ. I think this will have to replace my 650 with carto tank as my "out and about" setup.
I noticed that at first- took about 3 tanks to break in the coil, but now it wicks great and hits hard. Definitely the best clearo I have owned!
The exactly happen to me also, it was working finely until once the juice got low it started leaking on me =(.
Take it off the battery and give it about 4 primer puffs after i did that no dry hits for a while
After reading the posts in this thread, I ordered four of the Evods with four replacement heads. I've been chain vaping the first one for about three hours straight and so far, nothing but yummy with a ton of vapor. I did make sure the original head was screwed all the way in before filling, then gave it a few primer pulls with all the airholes and the bottom blocked off. Then I let it stand up on the desk for about 5 minutes before use. Hopefully, this will help those who are getting dry hits. I'm really loving this thing so far!
I have been vaping on Evods exclusively for the last couple of weeks and haven not had any trouble out of them so far. I have not experienced any gurgling or leaking. The only thing that I have noticed is that the coil head unscrews from the base sometimes when I remove the base to re-fill. Now I try to check to see if the coil head is tight each time.
I normally test fire my clearos if they have been sitting for a while, like overnight. I listen to how quickly the juice starts to sizzle, if it is slow to sizzle, then I know that the wick is oversaturated and may gurgle if I try to take a drag. If that is the case I fire it a few more times until I hear it sizzling pretty quickly. Then I take a vape. It seems like if the wick is oversaturated and I take a vape the clearo is more likely to flood. This has been my experience with T3's anyway, and I just do it out of habbit now with the Evods as well.
I normally test fire my clearos if they have been sitting for a while, like overnight. I listen to how quickly the juice starts to sizzle, if it is slow to sizzle, then I know that the wick is oversaturated and may gurgle if I try to take a drag. If that is the case I fire it a few more times until I hear it sizzling pretty quickly. Then I take a vape. It seems like if the wick is oversaturated and I take a vape the clearo is more likely to flood. This has been my experience with T3's anyway, and I just do it out of habbit now with the Evods as well.
Iv used one evod for a day and compared it to a Vapeonly BCC. The Evod wins hands down. Then again they are both similar in design and Iv got high hopes for the vapeonly rebuild with SS or less wick filling the holes..
Anyway.. Thumbs up for the Evod. Why mess with Genny's when these are available.
Anyway.. Thumbs up for the Evod. Why mess with Genny's when these are available.
- Status
Similar threads
