Just got two his week and they are amazing. Of course I have to use an adapter with my vamo but haven't had an issue so far. Really do wish I could use a stainless drip tip with it though. My only complaint though.
Kanger T3 -ZOMG
- Thread starter J.R. Bob Dobbs
- Start date
- th_trl_thread_readers 0
- Status
I like the drip tips that come with the T3 so for me that's not a issue.. The down side to the T3 is the connection but the adapter works just fine.. It's well worth it.. The T3 is the best juice holder I've tried..
I purchased a 510-ego adapter to use the MT3 (same connector as the T3) with my Vamo. Unfortunately, the Kanger won't fit on the adapter- the adapter circumference is too small and won't make contact with the kanger threads.
Any suggestions/links to an adapter that would work?
Any suggestions/links to an adapter that would work?
I like 'em, but they seem to be pretty picky, working with some juices much better than others. They also seem to leak terribly once they get really low, again, varying depending on the juice I use.
I have been using T3's for the past several weeks.
I am very happy with them.
They are easy to rebuild...... I have to get out my reading glasses but they are very easy to rebuild.
I am very happy with them.
They are easy to rebuild...... I have to get out my reading glasses but they are very easy to rebuild.
I got my eGo adapter from RTD Vapor... Their website isn't working right now, or I'd post a link.
Works good with the Vamo + T3... Good thing it does too, since that's the only reason I got it
I just got 4 MT3's today (Still T3's with metal tubes)
I do like the flavor I get from them...
Doesn't seem to give me the big plumes of vape I've grown accustomed to from the Vivi Nova's or a Carto/Tank setup. That may be due to the airy draw. I'll try to plug a hole and see if that makes a difference
I do quite like it other than that though. Works great on Vamo and Lavatube v2 with an adapter.
I do like the flavor I get from them...
Doesn't seem to give me the big plumes of vape I've grown accustomed to from the Vivi Nova's or a Carto/Tank setup. That may be due to the airy draw. I'll try to plug a hole and see if that makes a difference
I do quite like it other than that though. Works great on Vamo and Lavatube v2 with an adapter.
Just got one today. Unscrewed the bottom to fill. Filled with Jolly Farmer Green Apple juice. Screwed the bottom back on. Let it set for about 10 minutes. Attached to my eGo Twist set at 3.7 volts. Took a puff. Nasty. Good vapor. Backed off the T3 off of the battery a little. Took a puff. Nasty, still good vapor but with it burning my throat. Unscrewed the bottom of the T3 a tad. Took a puff. Just as nasty. Still great vapor. Let it set for another 10 minutes. Took a puff. Still nasty, with a taste of plastic, burnt motor oil, and yet another burning in my throat. Not impressed. Probably won't use it again. Unscrewed the T3 off of my eGo Twist. Set the T3 on my desk. Grabbed my Mini Vivi Nova filled with Sweet Tart. Screwed the mini onto my eGo Twist, set at 3.7 volts. Took a puff. Flavor off a tad, great vapor. Impressed. Been using the Nova's for about a month now. Will stick with those for a tank.
Last edited:
Did you try the Sweet Tart in the T3? Some say some juices are better than others on them. I've been using a 70/30 pg/vg menthol in my two MT3s and the only problem I run into is the flooding others are seeing when the juice level gets real low. Other than that, I love mine.
FYI: I bought a 510>eGo adapter from Provape.com and my Kanger T3s work great on my 510 threaded Provari.
Have you considered purchasing such an adapter?
What was your ohm rating on the T3 bottom coil unit rated at? An authentic Kanger T3 only comes in 2.5ohms, which comes out to 4.5 volts as a starting point. If you used T3 bottom coil units produced by Vision @ 1.8ohms, the 1.8ohms at 3.7 volts, that sounds about right.
You didn't wash it prior to use. Wash ALL of them prior to use. To prime when freshly filled take a couple of drags without operating the battery or just blow into it. When you see bubbles coming up it's priming ok
I fiddled with it and saw on youtube that there is a flavor wick on these things. The dude was explaining that said that the flavor wick may be preventing the normal wicks from wicking. So I removed the one strand of wicking on the very top of the coil. Haven't had a dry hit yet.
I did wash the tank out before I used it. Ran a little vodka through it, rinsed it out and let it air dry.
The T3 I have is a 1.8ohm. I ended up taking out one strand of flavor wick and haven't had an issue. I am still running it at 3.7, and it's actually ok. Flavor is a tad muted though.
No, I haven't tried the Sweet Tart in it yet. I may empty what I have left and re-rinse it and start over with the Sweet Tart. This is the first time trying the Green Apple, and it's not really all that good.
That's a shame
Being a newbie to this, I saw you say green apple and I thought "hmm, gonna have to write that one down to try".
Last edited:
I used a PG 80% VG 20% blend juice in my Baby T3 and it did flood - I think that blend is just too thin.
Also, I just got juice today and the letter that came with it states:
Please refrain from using the following flavors in plastic tank mods: Licorice, Cinnamon & Citrus Flavors, Mt. Dew, Sweet Tarts, Green Apple, Ginger, Maraschino Cherry, Root Beer, Amaretto, and Lavender.
- Status
Similar threads
